Jenn-Air W10394575A installation instructions Reinstall Kick Plate, Complete Installation

Page 12

8.Turn the control knob to LO and using a butane extension lighter, light the burner.

9.Remove the control knob.

10.Use a ¹⁄₈" x 4¼" flat-blade screwdriver to adjust the flame height. Tighten screw to reduce flame height. Loosen screw to increase flame height.

NOTE: When you are converting to LP gas, the screw should be tightened down completely on the single output valves. The dual output valve should not be adjusted.

AB

A. Single flame burner adjustment screw (on right side of valve) B. Dual flame burner adjustment screw (on left side of valve)

11.When finished adjusting the flame height, put a control knob back onto the valve stem and turn off the burner.

12.Remove the control knob.

13.Replace the round gasket.

14.Repeat steps 6 through 13 for any other burners that need adjustment.

15.Lift up on the control console and set it back into place. For a proper fit, the flange of the control console must hook over the lip on the front of the range cooktop.

A

B

A. Control console flange

B. Front lip of range cooktop

16.Check that the control console is flush with the top edge of the range.

A

A. Flush with range top

17.Replace the 2 screws on each side of the control console.

18.Replace the control knobs.

19.Replace burner grates.

20.Test the flame by turning the control from LO to HI, checking the flame at each setting.

Reinstall Kick Plate

1.Align shoulder screw mounting holes with shoulder screws on range.

2.Push kick plate down against front of range until the top screw holes are aligned with the mounting holes on the front of the range.

3.Reattach screws to the top of the kick plate.

B

C

A

D

A. Kick plate

B. Reattach these screws.

C. Top screw hole

D. Shoulder screw mounting hole

Complete Installation

1.Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.

2.Check that you have all of your tools.

3.Dispose of/recycle all packaging materials.

4.For oven use and cleaning, read the Use and Care Guide.

Check Operation of Oven Bake Burner(s)

1.Remove the oven racks and bake burner cover and set them aside on a covered surface.

2.Start a Bake cycle. See the Use and Care Guide for operating instructions.

The oven bake burner should light within 8 seconds. Under certain conditions it may take the burner up to 60 seconds to light.

Electronic igniters are used to light the bake burners.

NOTE: No adjustments can be made to the bake flames.

Check Operation of Oven Broil Burner

1.Remove the oven racks and set them aside on a covered surface.

2.Start a Broil cycle. See the Use and Care Guide for operating instructions.

The oven broil burner should light within 8 seconds. Under certain conditions it may take the burner up to 60 seconds to light.

Electronic igniters are used to light the broil burner.

NOTE: No adjustments can be made to the broil flames.

If you need Assistance or Service:

Please reference the “Assistance or Service” section of the Use and Care Guide or contact the dealer from whom you purchased your range.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Installation Instructions Range Safety Your safety and the safety of others are very importantInstallation Requirements Tools and PartsMobile Home Additional Installation Requirements Product Dimensions 30 76.2 cm modelsMobile home installations require Location RequirementsCabinet Dimensions 48 121.9 cm modelsElectrical Requirements Gas Supply RequirementsType of Gas Natural GasGas Supply Pressure Testing Gas Supply LineGas Pressure Regulator Burner Input Rating AltitudeInstallation Instructions Install Anti-Tip BracketUnpack Range Measurement BMake Gas Connection Floor MountingWall Mounting Install Griddle Verify Anti-Tip Bracket LocationLevel Range Complete ConnectionElectronic Ignition System Reinstall Kick Plate Complete InstallationIf you need Assistance or Service Check Operation of Oven Bake BurnersGAS Conversions LP Gas ConversionTo Convert Gas Pressure Regulator Gas Supply Pressure Testing Pull electrode out of bracket Replace Oven Bake Burner Cover ABBAB C Pull electrode out of bracket To Convert Surface Burners Burner orifice spudComplete Installation Natural Gas Conversion Line pressure testing above ½ psi gauge 14 WCP Pull electrode out of bracket Replace Oven Bake Burner Cover AB C Pull electrode out of bracket 000 BTU 01 mm Small burners 15,000 BTU 75 mm Wiring Diagrams Atlas48 121.9 cm Oven Schematic for JGRP548 Model User Interface UI HMI KeyboardBurner Cooktop Schematic Strip CircuitsSW1 Sécurité DE LA Cuisinière Votre sécurité et celle des autres est très importanteExigences Dinstallation Outils et piècesExigences d’emplacement Dimensions du produit Modèles de 30 76,2 cmModèles de 36 91,4 cm Dimensions du placard Revêtement de hotte au-dessus de la cuisinière, suivre lesSpécifications électriques Spécifications de lalimentation en gazType de gaz Canalisation de gaz DétendeurDébit thermique des brûleurs Altitude Test de pressurisation de la canalisation de gazInstructions D’INSTALLATION Installation de la bride antibasculementDéballage de la cuisinière Mesure BRaccordement au gaz Montage au plancherMontage au mur Vérification de lemplacement de la bride Antibasculement Installation de la plaque à frireRéglage de laplomb de la cuisinière Achever le raccordementSystème dallumage électronique Réinstallation du garde-pieds Réinstaller les vis au sommet du garde-piedsAchever l’installation Conversions Pour Changement DE GAZConversion pour lalimentation au propane Conversion du détendeur Test de pressurisation de la canalisation de gazCouvercle du brûleur de cuisson au four Dégager lélectrode du support Réinstaller le couvercle du brûleur de cuisson au four AB C Dégager lélectrode du support Conversion des brûleurs de surface Gicleur de brûleurAchever l’installation Conversion pour lalimentation au gaz naturel Déflecteur du four Écrous du déflecteur du four Lame plate puis retirer lélectrode Réinstaller le couvercle du brûleur de cuisson au four AB C Dégager lélectrode du support Réinstaller le couvercle du brûleur de cuisson au four 15 000 BTU 75 mm Schémas de câblage RemarquesSchéma du four de 48 121,9 cm pour modèle JGRP548 Interface Utilisateur IUSchémas des circuits Schéma de la table de cuisson à 4 brûleursSW2 Schéma de la table de cuisson à 6 brûleursW10394575A

W10394575A specifications

The Jenn-Air W10394575A is a premium kitchen appliance that embodies the fusion of design, functionality, and cutting-edge technology, elevating the cooking experience for culinary enthusiasts and home chefs alike. This product is designed to offer superior performance while enhancing the aesthetic appeal of modern kitchen spaces.

One of the standout features of the Jenn-Air W10394575A is its high-efficiency performance, which is driven by innovative technology that ensures consistent heating and cooking results. The appliance is equipped with powerful heating elements that provide quick responsiveness, reducing overall cooking time. With its precise temperature control, users can expect impeccable results in every dish, from delicate pastries to hearty casseroles.

A key characteristic of the Jenn-Air W10394575A is its elegant design, tailored to fit seamlessly into contemporary kitchen interiors. The sleek lines and high-quality materials used in its construction not only create a visually stunning appliance but also ensure durability and long-term reliability. The surface is designed for easy cleaning, allowing users to maintain its pristine appearance with minimal effort.

In addition to its aesthetic appeal, the Jenn-Air W10394575A also incorporates user-friendly features that enhance the cooking experience. Its intuitive interface includes a digital display and straightforward controls, making it easy for users to select their desired settings. The appliance offers multiple cooking modes, catering to various culinary techniques such as baking, broiling, and warming, which provides versatility for different cooking styles.

Safety is another priority in the design of the Jenn-Air W10394575A. The appliance comes equipped with advanced safety features, including automatic shut-off and cool-touch surfaces, ensuring a secure cooking environment. This attention to safety allows users—regardless of expertise—to cook with confidence.

Overall, the Jenn-Air W10394575A is a remarkable addition to any kitchen, combining stylish design, advanced technology, and practical features. It is ideal for anyone who appreciates quality and performance, transforming everyday cooking into a refined culinary experience. Whether you're preparing a casual family meal or hosting a dinner party, this appliance is designed to meet and exceed the needs of modern homeowners.
Top Page Image Contents