Jenn-Air W10253462A installation instructions Connect Range to Downdraft System

Page 19

2.Attach terminal lugs to line 1 (black), bare (green) ground, and line 2 (red) wires. Loosen (do not remove) the set screw on the front of the terminal lug and insert exposed wire end through bottom of terminal lugs. Securely tighten set screw to torque as shown in the following Bare Wire Torque Specifications chart.

A

B

C D E

A. Terminal lug

B. Set screw

C. Line 1 (black) wire

D. Bare (green) ground wire

E. Line 2 (red) wire

Bare Wire Torque Specifications

Attaching terminal lugs to the terminal block - 20 lbs-in. (2.3 N-m)

Wire Awg

Torque

8 gauge copper

25 lbs-in. (2.8 N-m)

 

 

6 gauge aluminum

35 lbs-in. (4.0 N-m)

 

 

3.Use ³⁄₈" nut driver to connect the bare (green) ground wire to the center terminal block post with one of the 10–32 hex nuts.

F

A

E

B

 

D

 

C

A. 10–32 hex nut

D. Bare (green) ground wire

B. Line 1 (black)

E. Line 2 (red)

C. Ground-link screw

F. Terminal lug

4.Connect line 1 (black) and line 2 (red) wires to the outer terminal block posts with 10-32 hex nuts.

5.Securely tighten hex nuts.

6.Replace terminal block access cover.

Connect Range to Downdraft System

1.Attach flexible vent (provided) to the blower motor inlet using a vent clamp.

2

1

 

A

B

A. Inlet flexible vent

B. Vent clamp

2.Check countertop height to allow range top to clear countertop. Adjusting leveling legs if necessary.

3.Remove access panel by grasping both sides, pulling upward, and lifting out.

4.Move range close to cabinet opening.

5.Plug range into grounded outlet (if using a power supply cord).

6.Plug range electrical connector into the downdraft blower motor.

A

B

A. Power supply cord (on some installations)

B. Range electrical connector to blower motor

7.Remove cardboard or hardboard from under the range. Using

2 or more people, gently move range into its final location.

19

Image 19
Contents Table of Contents/Table des matières Your safety and the safety of others are very important Range SafetyTools and Parts Installation RequirementsLocation Requirements Product Dimensions Cabinet Dimensions Floor Venting Venting RequirementsVenting Methods Wall VentingLeft or Right Side Venting Concrete Slab Installations Exhaust Through WallConcrete Slab Installations Exhaust Through Window Well Calculating Vent System LengthElectrical Connection If connecting to a 4-wire systemElectrical Requirements U.S.A. Only Example vent systemElectrical Requirements Canada Only If connecting to a 3-wire systemCountertop Preparation Unpack Range Installation InstructionsAdjust Leveling Legs Install Anti-Tip BracketDetermine Equivalent Length of Vent System Install Downdraft SystemRear Wall Venting Go to the Electrical Connection section View from Motor Side of Blower Wood spacers Mounting bracket Blower Electrical Connection U.S.A. Only Power Supply CordDirect Wire Style 1 Power supply cord strain reliefStyle 2 Direct wire strain relief Wire connection Power Supply Cord Wire Connection Direct Wire Wire Awg Torque Bare Wire Torque SpecificationsConnect Range to Downdraft System Side Venting left side venting shown Wall Venting Top View Floor VentingMoving the Range Complete InstallationIf you need Assistance or Service For power supply cord-connected rangesFor direct-wired ranges Votre sécurité et celle des autres est très importante Sécurité DE LA CuisinièreExigences d’emplacement Exigences D’INSTALLATIONOutils et pièces Dimensions du produit Dimensions du placardAir d’appoint Installations dans les régions au climat froidExigences concernant l’évacuation Pour obtenir des performances optimalesÉvacuation par la gauche ou par la droite Installations sur dalle de béton Évacuation par le murMéthodes d’évacuation Évacuation par le plancherLongueur maximum = 60 pi 18,3 m Calcul de la longueur effective du circuit d’évacuationExemple de circuit d’évacuation Composant Conduit de diamètre de 15,2 cmPréparation du plan de travail Spécifications électriquesDéballage de la cuisinière Instructions D’INSTALLATIONRéglage des pieds de nivellement Installation du circuit d’évacuation Par le bas Installation de la bride antibasculementDéterminer la longueur équivalente du circuit d’évacuation Vue de dessus Évacuation par le mur arrière22,8 cm Vue du ventilateur côté moteur Placer 2 cales en bois et les fixer au sol Évacuation par le plancher Vue de dessus Évacuation par le mur Vue de dessusSi vous avez besoin d’assistance ou de service Achever l’installationPour les cuisinières avec câblage direct Déplacement de la cuisinièreCuisinières alimentées par cordon d’alimentation Page 2009 All rights reserved W10253462A

W10253462A specifications

The Jenn-Air W10253462A is a highly regarded appliance in the realm of kitchen innovation. This sophisticated range is known for its blend of style, versatility, and cutting-edge technology, making it an essential addition for both cooking enthusiasts and professional chefs alike.

One of the main features of the W10253462A is its powerful induction cooking capabilities. Induction cooking utilizes electromagnetic energy to heat pots and pans directly, resulting in faster cooking times and improved energy efficiency. This technology not only reduces cooking time but also provides precise temperature control, allowing for a seamless cooking experience. Additionally, the smooth surface of the induction cooktop makes it easy to clean, as spills can be wiped away without difficulty.

Another standout characteristic of the W10253462A is its oven performance. This model typically includes a convection oven which circulates hot air for even cooking results. The convection feature ensures that meals are cooked evenly, reducing the chances of hot spots and undercooked areas. Furthermore, with multiple cooking modes, users can roast, bake, or broil with ease, providing versatility for various recipes.

The appliance often includes advanced safety features as well. For example, the induction cooktop generally comes with automatic shut-off functionality, which turns off the burners if no cookware is detected, ensuring peace of mind when cooking. Additionally, child lock settings are available, making this range a safe option for families.

In terms of aesthetics, the Jenn-Air W10253462A typically boasts a sleek, modern design that complements any kitchen decor. The stainless steel finish not only enhances its visual appeal but also contributes to its durability and resistance to smudges and fingerprints.

Moreover, the appliance often incorporates smart technology, allowing users to control their cooking settings remotely through a smartphone app. This innovation not only increases convenience but also enables users to monitor their dishes' progress from anywhere in the house.

The Jenn-Air W10253462A is truly a blend of sophisticated design and advanced technology, suitable for anyone looking to enhance their cooking experience. With its induction cooking, advanced oven features, safety mechanisms, and smart capabilities, this appliance stands out as a top choice for modern kitchens.