Jenn-Air W10253462A installation instructions Wire Connection Direct Wire

Page 17

3-wire connection: Power Supply Cord

 

Direct Wire Installation: Copper or Aluminum Wire

Use this method only if local codes permit connecting chassis ground conductor to neutral wire of power supply cord.

1.Feed the power supply cord through the opening in the cord/ conduit plate on bottom of range. Allow enough slack to easily attach the wiring to the terminal block.

A

B

C

D

A. Terminal block

B.Ground-link screw

C.Cord/conduit plate

D.Power supply cord wires

2.Use ³⁄₈" nut driver to connect the neutral (white) wire to the center terminal block post with one of the 10–32 hex nuts.

A

E

 

B

D

 

C

 

A. 10–32 hex nut

D. Neutral (white) wire

B. Line 1 (black)

E. Line 2 (red)

C.Ground-link screw

3.Connect line 1 (black) and line 2 (red) wires to the outer terminal block posts with 10-32 hex nuts.

4.Securely tighten hex nuts.

NOTE: For power supply cord replacement, only use a power cord rated at 250 volts minimum, 40 amps or 50 amps that is marked for use with nominal 1³⁄₈" (3.5 cm) diameter connection opening, with ring terminals and marked for use with ranges.

5.Replace terminal block access cover.

This range may be connected directly to the fuse disconnect or circuit breaker box. Depending on your electrical supply, make the required 3-wire or 4-wire connection.

1.Strip outer covering back 3" (7.6 cm) to expose wires. Strip the insulation back 1" (2.5 cm) from the end of each wire.

1"

(2.5 cm)

3"

(7.6 cm)

2.Allow enough slack in the wire to easily attach the wiring terminal block.

3.Complete electrical connection according to your type of electrical supply (4-wire or 3-wire connection).

4-wire Connection: Direct Wire

Use this method for:

■New branch-circuit installations (1996 NEC)

■Mobile homes

■Recreational vehicles

■In an area where local codes prohibit grounding through the neutral

1.Part of metal ground strap must be cut out and removed.

A

B

C

A. Metal ground strap

B.Discard

C.Ground-link screw

2.Use Phillips screwdriver to remove the ground-link screw from the back of the range. Save the ground-link screw and the end of the ground-link under the screw.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Table of Contents/Table des matières Your safety and the safety of others are very important Range SafetyLocation Requirements Installation RequirementsTools and Parts Product Dimensions Cabinet Dimensions Venting Methods Venting RequirementsWall Venting Floor VentingConcrete Slab Installations Exhaust Through Window Well Concrete Slab Installations Exhaust Through WallCalculating Vent System Length Left or Right Side VentingElectrical Requirements U.S.A. Only If connecting to a 4-wire systemExample vent system Electrical ConnectionCountertop Preparation If connecting to a 3-wire systemElectrical Requirements Canada Only Adjust Leveling Legs Installation InstructionsInstall Anti-Tip Bracket Unpack RangeRear Wall Venting Install Downdraft SystemDetermine Equivalent Length of Vent System Go to the Electrical Connection section View from Motor Side of Blower Wood spacers Mounting bracket Blower Direct Wire Power Supply CordStyle 1 Power supply cord strain relief Electrical Connection U.S.A. OnlyStyle 2 Direct wire strain relief Wire connection Power Supply Cord Wire Connection Direct Wire Wire Awg Torque Bare Wire Torque SpecificationsConnect Range to Downdraft System Side Venting left side venting shown Wall Venting Top View Floor VentingIf you need Assistance or Service Complete InstallationFor power supply cord-connected ranges Moving the RangeFor direct-wired ranges Votre sécurité et celle des autres est très importante Sécurité DE LA CuisinièreOutils et pièces Exigences D’INSTALLATIONExigences d’emplacement Dimensions du produit Dimensions du placardExigences concernant l’évacuation Installations dans les régions au climat froidPour obtenir des performances optimales Air d’appointMéthodes d’évacuation Installations sur dalle de béton Évacuation par le murÉvacuation par le plancher Évacuation par la gauche ou par la droiteExemple de circuit d’évacuation Calcul de la longueur effective du circuit d’évacuationComposant Conduit de diamètre de 15,2 cm Longueur maximum = 60 pi 18,3 mPréparation du plan de travail Spécifications électriquesRéglage des pieds de nivellement Instructions D’INSTALLATIONDéballage de la cuisinière Déterminer la longueur équivalente du circuit d’évacuation Installation de la bride antibasculementInstallation du circuit d’évacuation Par le bas Vue de dessus Évacuation par le mur arrière22,8 cm Vue du ventilateur côté moteur Placer 2 cales en bois et les fixer au sol Évacuation par le plancher Vue de dessus Évacuation par le mur Vue de dessusSi vous avez besoin d’assistance ou de service Achever l’installationCuisinières alimentées par cordon d’alimentation Déplacement de la cuisinièrePour les cuisinières avec câblage direct Page 2009 All rights reserved W10253462A

W10253462A specifications

The Jenn-Air W10253462A is a highly regarded appliance in the realm of kitchen innovation. This sophisticated range is known for its blend of style, versatility, and cutting-edge technology, making it an essential addition for both cooking enthusiasts and professional chefs alike.

One of the main features of the W10253462A is its powerful induction cooking capabilities. Induction cooking utilizes electromagnetic energy to heat pots and pans directly, resulting in faster cooking times and improved energy efficiency. This technology not only reduces cooking time but also provides precise temperature control, allowing for a seamless cooking experience. Additionally, the smooth surface of the induction cooktop makes it easy to clean, as spills can be wiped away without difficulty.

Another standout characteristic of the W10253462A is its oven performance. This model typically includes a convection oven which circulates hot air for even cooking results. The convection feature ensures that meals are cooked evenly, reducing the chances of hot spots and undercooked areas. Furthermore, with multiple cooking modes, users can roast, bake, or broil with ease, providing versatility for various recipes.

The appliance often includes advanced safety features as well. For example, the induction cooktop generally comes with automatic shut-off functionality, which turns off the burners if no cookware is detected, ensuring peace of mind when cooking. Additionally, child lock settings are available, making this range a safe option for families.

In terms of aesthetics, the Jenn-Air W10253462A typically boasts a sleek, modern design that complements any kitchen decor. The stainless steel finish not only enhances its visual appeal but also contributes to its durability and resistance to smudges and fingerprints.

Moreover, the appliance often incorporates smart technology, allowing users to control their cooking settings remotely through a smartphone app. This innovation not only increases convenience but also enables users to monitor their dishes' progress from anywhere in the house.

The Jenn-Air W10253462A is truly a blend of sophisticated design and advanced technology, suitable for anyone looking to enhance their cooking experience. With its induction cooking, advanced oven features, safety mechanisms, and smart capabilities, this appliance stands out as a top choice for modern kitchens.
Top Page Image Contents