Jenn-Air W10526003A installation instructions Type of Gas, Gas Supply Line, Gas Pressure Regulator

Page 7

Type of Gas

Natural Gas:

This cooktop is design-certified by CSA International for use with Natural gas or, after proper conversion, for use with LP gas.

■This cooktop is factory set for use with Natural gas. If converting to LP gas, see the “LP Gas Conversion” instructions provided in the package containing literature. The model/serial rating plate located on the underside of the cooktop base has information on the types of gas that can be used. If the types of gas listed do not include the type of gas available, check with the local gas supplier.

LP Gas Conversion:

Conversion must be done by a qualified service technician.

No attempt shall be made to convert the cooktop from the gas specified on the model/serial rating plate for use with a different gas without consulting the serving gas supplier. To convert to LP gas, use the LP gas conversion kit provided with the cooktop and see the “Gas Conversions” section.

Gas Supply Line

■Provide a gas supply line of ³⁄₄" (1.9 cm) rigid pipe to the cooktop location. A smaller size pipe on longer runs may result in insufficient gas supply. Pipe-joint compounds that resist the action of LP gas must be used. Do not use TEFLON®† tape. With LP gas, piping or tubing size should be ½" minimum. Usually, LP gas suppliers determine the size and materials used in the system.

Flexible metal appliance connector:

■If local codes permit, use a ¹⁄₂" or ³⁄₄" I.D. flexible stainless steel tubing gas connector, designed by CSA to connect the cooktop to the rigid gas supply line.

■Must include a shutoff valve:

The supply line must be equipped with a manual shutoff valve. This valve should be located in the same room but external to the cooktop opening, such as an adjacent cabinet. It must be accessible without removing the cooktop, and it should be in a location that allows ease of opening and closing. Do not block access to shutoff valve. The valve is for turning on or shutting off gas to the cooktop.

B

A

C

A. Gas supply line

B. Shutoff valve “open” position

C. To cooktop

Gas Pressure Regulator

The gas pressure regulator supplied with this cooktop must be used. The inlet pressure to the regulator should be as follows for proper operation:

Natural Gas:

Minimum pressure: 5" (12.7 cm) WCP

Maximum pressure: 7" to 14" (17.8 cm to 35.5 cm) WCP

LP Gas:

Minimum pressure: 10" (25.4 cm) WCP

Maximum pressure: 14" (35.5 cm) WCP

Contact local gas supplier if you are not sure about the inlet pressure.

■A ½" male pipe thread is needed for connection to the female pipe threads of the inlet to the cooktop pressure regulator.

■Do not kink or damage the flexible metal tubing when moving the cooktop.

Rigid pipe connection:

The rigid pipe connection requires a combination of pipe fittings to obtain an in-line connection to the cooktop. The rigid pipe must be level with the cooktop connection. All strains must be removed from the supply and fuel lines so cooktop will be level and in line.

Burner Input Requirements

Input ratings shown on the model/serial rating plate are for elevations up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings should be reduced at a rate of 4% for each 1,000 ft (304.8 m) above sea level (not applicable for Canada).

Gas Supply Pressure Testing

Gas supply pressure for testing regulator must be at least

1" water column pressure above the manifold pressure shown on the model/serial rating plate.

Line pressure testing above ½ psi gauge (14" WCP)

The cooktop and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of ½ psi (3.5 kPa).

Line pressure testing at ½ psi gauge (14" WCP) or lower

The cooktop must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than ½ psi (3.5 kPa).

†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents DE 48 121,9 CM Your safety and the safety of others are very important Cooktop SafetyTools and Parts Installation RequirementsLocation Requirements For Best Performance Cutout DimensionsCabinet Dimensions Venting RequirementsVenting Methods Concrete Slab Installations Exhaust Through WallCalculating Vent System Length Gas Supply Requirements Electrical RequirementsExample vent system Gas Pressure Regulator Gas Supply Pressure TestingType of Gas Gas Supply LineRotate Blower Optional Installation InstructionsComplete Connection Make Gas ConnectionTypical flexible connection Check Operation of Surface Burners Adjust Flame HeightAdjust Air Shutter Burner IgnitionIf you need Assistance or Service Complete InstallationTo Convert Gas Pressure Regulator Gas Supply Pressure TestingGAS Conversions LP Gas ConversionNatural Gas Conversion Complete InstallationTo Convert Surface Burners To Convert Surface Burners Votre sécurité et celle des autres est très importante Sécurité DE LA Table DE CuissonExigences d’emplacement Exigences DinstallationOutillage et pièces Dimensions de l’ouverture à découper Dimensions du produit Table de cuisson de 48 121,9 cmMéthodes d’évacuation Exigences concernant l’évacuationComposant Conduit de diamètre de 15,2 cm Installations sur dalle de béton Évacuation par le murCalcul de la longueur du circuit d’évacuation Exemple de circuit d’évacuationGaz naturel Spécifications électriquesSpécifications de lalimentation en gaz Type de gazTest de pressurisation de la canalisation de gaz Canalisation de gazDétendeur de gaz Caractéristiques dalimentation du brûleurInstallation de la table de cuisson Instructions D’INSTALLATIONRotation du ventilateur facultative Raccordement typique par raccord flexible Raccordement au gazRéglage de la taille des flammes Allumage des brûleursAchever le raccordement Contrôle du fonctionnement des brûleurs de surfaceSi vous avez besoin d’assistance ou de service Achever linstallationRéglage de ladmission dair Conversion des brûleurs de surface Conversions Pour Changement DE GAZConversion pour lalimentation au propane Conversion du détendeurConversion pour lalimentation au gaz Naturel Achever l’installationImprimé aux É.-U

W10526003A specifications

The Jenn-Air W10526003A is a premium appliance component designed to enhance the performance and functionality of modern kitchens. This high-quality product is primarily a replacement part for various Jenn-Air refrigerator models, ensuring that your appliance remains efficient and reliable over time. Understanding the main features, technologies, and characteristics of the W10526003A can help homeowners and appliance repair technicians make informed decisions when it comes to appliance maintenance.

One of the standout features of the W10526003A is its durable construction. Made from high-quality materials, this component is designed to withstand the rigors of daily use while maintaining its functionality. This resilience is essential for homeowners who rely on their refrigerators to keep food fresh and safe to consume.

The W10526003A is engineered with advanced technology to ensure optimal performance. It is designed to fit specific Jenn-Air models seamlessly, contributing to the overall efficiency of the appliance. The precise engineering behind this part reduces the likelihood of malfunctions, providing peace of mind for users who depend on their refrigerator for food preservation.

Another significant characteristic of the Jenn-Air W10526003A is its ease of installation. This component can be swapped out with minimal effort, making it accessible for DIY enthusiasts and professional repair technicians alike. Clear instructions are typically provided, ensuring that users can complete the installation process without hassle.

In addition to its durable and efficient design, the W10526003A is also built with energy efficiency in mind. By ensuring that the refrigerator operates at optimal levels, this replacement part can contribute to lower energy consumption, which is not only beneficial for the environment but also decreases utility bills.

Moreover, the W10526003A is compatible with a range of Jenn-Air refrigerator models, making it a versatile choice for various configurations. This compatibility allows users to confidently select this part, knowing that it will work effectively with their specific appliances.

In conclusion, the Jenn-Air W10526003A represents a high-quality replacement option for those looking to maintain or repair their refrigerators. With its durable construction, advanced technology, easy installation process, and energy efficiency, it stands out as a reliable choice for enhancing the overall performance of Jenn-Air appliances. By investing in this component, homeowners can ensure that their kitchen remains a well-functioning hub for food storage and preparation.
Top Page Image Contents