Jenn-Air W10526003A Electrical Requirements, Gas Supply Requirements, Example vent system

3¹⁄₄" x 10" (8.3 cm x 25.4 cm)	4.5 ft
to 6" (15.2 cm) transition	(1.4 m)
6" (15.2 cm) to 3¹⁄₄" x 10"	1 ft
(8.3 cm x 25.4 cm) transition	(0.3 m)
3¹⁄₄" x 10" (8.3 cm x 25.4 cm)	5.0 ft
to 6" (15.2 cm) 90° elbow	(1.5 m)
transition
6" (15.2 cm) to 3¹⁄₄" x 10"	5.0 ft
(8.3 cm x 25.4 cm) 90° elbow	(1.5 m)
transition
3¹⁄₄" x 10" (8.3 cm x 25.4 cm)	5.0 ft
90° elbow	(1.5 m)
3¹⁄₄" x 10" (8.3 cm x 25.4 cm)	12.0 ft
flat elbow	(3.7 m)
3¹⁄₄" x 10" (8.3 cm x 25.4 cm)	0.0 ft
wall cap	(0.0 m)

Example vent system

wall cap

90˚ elbow

6 ft (1.8 m)

2ft

(0.6 m)

1- 90° elbow	= 5 ft (1.5 m)
8 ft (2.4 m) straight	= 8 ft (2.4 m)
1 - wall cap	= 0 ft (0 m)
System length	= 13 ft (3.9 m)

NOTE: Flexible vent is not recommended. Flexible vent creates back pressure and air turbulence that greatly reduce performance.

6

Electrical Requirements

IMPORTANT: The cooktop must be electrically grounded in accordance with local codes and ordinances, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.

This cooktop is equipped with an electronic ignition system that will not operate if plugged into an outlet that is not properly polarized.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

■A 120 volt, 60 Hz, AC only, 15-amp, fused electrical circuit is required. A time-delay fuse or circuit breaker is also recommended. It is recommended that a separate circuit serving only this cooktop be provided.

■Electronic ignition systems operate within wide voltage limits, but proper grounding and polarity are necessary. Check that the outlet provides 120-volt power and is correctly grounded.

■The wiring diagrams are provided with this cooktop. See “Wiring Diagrams” on a separate sheet. The wiring diagrams are located on the left underside of the cooktop base.

Gas Supply Requirements

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure gas pressure does not exceed 14" (36 cm) water column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Observe all governing codes and ordinances.

IMPORTANT: This installation must conform with all local codes and ordinances. In the absence of local codes, installation must conform with American National Standard, National Fuel Gas Code ANSI Z223.1 - latest edition or CAN/CGA B149 - latest edition.

IMPORTANT: Leak testing of the cooktop must be conducted according to the manufacturer’s instructions.