Jenn-Air W10526003A installation instructions Installation Instructions, Rotate Blower Optional

Page 8

INSTALLATION INSTRUCTIONS

b.) Position the cooktop in the countertop cutout. The main

Install Cooktopcontrol panel should overlap the top of the lower control panel as shown in the following illustration.

Decide on the final location for the cooktop.

WARNING

Excessive Weight Hazard

Use two or more people to move and install cooktop. Failure to do so can result in back or other injury.

1.Open carton as instructed on product packaging.

2.Remove shipping materials and tape from cooktop.

3.Remove the removable grease filter by lifting the filter out.

4.For island or peninsula installations, go to the “Rotate Blower - Optional” section.

A

A. Removable grease filter

5.(For some installations only): Installation of the lower control panel is required for installations when the cabinet front cutout is greater than 5¾" (14.6 cm) from the top of the countertop.

a.) Install the lower control panel in the bottom of the cabinet cutout as shown in the following illustration using the screws from the hardware pack.

A

B

C

A. Top view

B. Lower control panel

C. Cabinet front cutout

A

A. Lower control panel

NOTE: For some cabinet styles, it may be necessary to reinforce the front of the cabinet by attaching a brace from front to rear inside the cabinet under the burner box.

6.Using 2 or more people, remove the cooktop from the carton.

REMEMBER: An undercounter built-in oven cannot be installed under this cooktop.

7.Place cooktop right side up into the cutout.

NOTE: Make sure that the front edge of the cooktop is parallel to the front edge of the countertop. If repositioning is needed, lift entire cooktop up from the cutout to avoid scratching the countertop.

8.Connect blower exhaust scroll to ducting.

9.Use vent clamps to secure the ducting to the blower exhaust scroll.

10.Reinstall grease filter.

11.Reinstall vent grille.

Rotate Blower - Optional

IMPORTANT: The following additional step must be performed if the product is being installed in peninsula or island cabinetry.

The blower exhaust scroll is shipped from the factory set to exhaust straight out the back of the cabinet through an exterior wall. The blower may be rotated for horizontal or vertical direction by loosening the nuts around the blower inlet, accessible inside the ventilation chamber.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents DE 48 121,9 CM Cooktop Safety Your safety and the safety of others are very importantLocation Requirements Installation RequirementsTools and Parts Cutout Dimensions Cabinet DimensionsVenting Requirements For Best PerformanceCalculating Vent System Length Concrete Slab Installations Exhaust Through WallVenting Methods Example vent system Electrical RequirementsGas Supply Requirements Gas Supply Pressure Testing Type of GasGas Supply Line Gas Pressure RegulatorInstallation Instructions Rotate Blower OptionalTypical flexible connection Make Gas ConnectionComplete Connection Adjust Flame Height Adjust Air ShutterBurner Ignition Check Operation of Surface BurnersComplete Installation If you need Assistance or ServiceGas Supply Pressure Testing GAS ConversionsLP Gas Conversion To Convert Gas Pressure RegulatorTo Convert Surface Burners Complete InstallationNatural Gas Conversion To Convert Surface Burners Sécurité DE LA Table DE Cuisson Votre sécurité et celle des autres est très importanteOutillage et pièces Exigences DinstallationExigences d’emplacement Dimensions du produit Table de cuisson de 48 121,9 cm Dimensions de l’ouverture à découperExigences concernant l’évacuation Méthodes d’évacuationInstallations sur dalle de béton Évacuation par le mur Calcul de la longueur du circuit d’évacuationExemple de circuit d’évacuation Composant Conduit de diamètre de 15,2 cmSpécifications électriques Spécifications de lalimentation en gazType de gaz Gaz naturelCanalisation de gaz Détendeur de gazCaractéristiques dalimentation du brûleur Test de pressurisation de la canalisation de gazRotation du ventilateur facultative Instructions D’INSTALLATIONInstallation de la table de cuisson Raccordement au gaz Raccordement typique par raccord flexibleAllumage des brûleurs Achever le raccordementContrôle du fonctionnement des brûleurs de surface Réglage de la taille des flammesRéglage de ladmission dair Achever linstallationSi vous avez besoin d’assistance ou de service Conversions Pour Changement DE GAZ Conversion pour lalimentation au propaneConversion du détendeur Conversion des brûleurs de surfaceAchever l’installation Conversion pour lalimentation au gaz NaturelImprimé aux É.-U

W10526003A specifications

The Jenn-Air W10526003A is a premium appliance component designed to enhance the performance and functionality of modern kitchens. This high-quality product is primarily a replacement part for various Jenn-Air refrigerator models, ensuring that your appliance remains efficient and reliable over time. Understanding the main features, technologies, and characteristics of the W10526003A can help homeowners and appliance repair technicians make informed decisions when it comes to appliance maintenance.

One of the standout features of the W10526003A is its durable construction. Made from high-quality materials, this component is designed to withstand the rigors of daily use while maintaining its functionality. This resilience is essential for homeowners who rely on their refrigerators to keep food fresh and safe to consume.

The W10526003A is engineered with advanced technology to ensure optimal performance. It is designed to fit specific Jenn-Air models seamlessly, contributing to the overall efficiency of the appliance. The precise engineering behind this part reduces the likelihood of malfunctions, providing peace of mind for users who depend on their refrigerator for food preservation.

Another significant characteristic of the Jenn-Air W10526003A is its ease of installation. This component can be swapped out with minimal effort, making it accessible for DIY enthusiasts and professional repair technicians alike. Clear instructions are typically provided, ensuring that users can complete the installation process without hassle.

In addition to its durable and efficient design, the W10526003A is also built with energy efficiency in mind. By ensuring that the refrigerator operates at optimal levels, this replacement part can contribute to lower energy consumption, which is not only beneficial for the environment but also decreases utility bills.

Moreover, the W10526003A is compatible with a range of Jenn-Air refrigerator models, making it a versatile choice for various configurations. This compatibility allows users to confidently select this part, knowing that it will work effectively with their specific appliances.

In conclusion, the Jenn-Air W10526003A represents a high-quality replacement option for those looking to maintain or repair their refrigerators. With its durable construction, advanced technology, easy installation process, and energy efficiency, it stands out as a reliable choice for enhancing the overall performance of Jenn-Air appliances. By investing in this component, homeowners can ensure that their kitchen remains a well-functioning hub for food storage and preparation.
Top Page Image Contents