Bloomfield 2030 owner manual Operation

Page 12

OPERATION (continued)

12.View Filter Statistics: To view filter statistics, turn the brewer off. Press and hold the 1st key (Brew), and depress the 3rd (ON/OFF) key. Total water volume will be displayed (TotalVol.). Press the 3rd key to view the Filter Life (FltrLife:). Press the 3rd key to view the percentage of the filter that has been used. (If the filter option is used, the filter life volume needs to be entered in the program – see E-Max™ Programming Manual, Service & Counters Menu.)

13.Diagnostic Messages – Programmed Safety Features: When E-Max T™ senses a problem, it will automatically turn off all elements and valves, flash lights, display the message

“Call For Service” and display one of the messages below. (Additionally: a service phone number may appear if it has been programmed into the system.)

*To reset the brewer it can be re-energized (or press and hold CANCEL for 3 seconds for all faults except the Valve Fault, which must be reset by re-energizing). The brewer will try to re-start, but if the same problem persists, the appropriate error message will appear again. Consult the Trouble Shooting section to determine how to solve the problem.

A.“Probe/Heater Error”: Overheating Detection (1): If the heating element is on for 5 minutes and the temperature does not change by +2°F (1°C) in the five minute period, the unit will go into the Over Temperature Mode with all lights flashing. When in this mode the brewer turns off the heating elements, the solenoid valves are turned off; the switches disabled; (and all lights flashing continuously). The LCD display will read “Probe/Heater Error”, followed by the message “Call for Service”, and then the service phone number (if it has been entered into memory). To reset press and hold CANCEL for 3 seconds, or re-energize the brewer. (Possible causes of problem: high limit needs to be re-set; defective high limit, element, triac, water level probe or control board.)

B.“Overheat Error”: Overheating Detection (2): If the E-Max™ senses a temperature over the Maximum Temperature set in the program (factory set at 208ºF or 98ºC) it will go into the over temperature mode as above with all lights flashing, except the LCD will read “overheat error”, and “Call for Service”. To reset press and hold CANCEL for 3 seconds, or re-energize the brewer. (Possible cause of problem is a defective triac, temperature probe or related wiring and connections.)

C.“No Water Sensed” — Time-Out—Inlet Valve: When filling for the first time, the inlet valve will remain open for 4¼ minutes, (the screen will read “filling…”). If water is not detected at the end of this time the E-Max will shut down with the message “no water sensed”. The valves and all elements are turned off, and the Brew and Power light flash alternately with the Heat light, until the brewer is reset. To reset press and hold CANCEL for 3 seconds, or re-energize the brewer. (Possible causes of the problem are: no incoming water; slow flow of incoming water (i.e. less than 45 oz/minute); sensor not reading (check for placement, connections or lime scale).

D.“No Water Sensed” — Time-Out – Brew Valve: During the brew the inlet solenoid valve cycles on intermittently to maintain the proper level in the tank. If the valve is open for

60 seconds without water being detected at the proper level, the brewer will go into the same error mode as above (“no water sensed”). To reset press and hold CANCEL for 3 seconds, or re-energize the brewer. (Possible causes of the problem are: no incoming water; slow flow of incoming water, sensor not reading, etc.).

E.Keyswitch Locked: If a key switch is depressed for 10 seconds this error message will occur. Lights will flash alternately and the brewer will turn off all valves and elements. Press and hold the CANCEL key for 3 seconds to reset the brewer (or re-energize the brewer). If the problem re-occurs this indicates a defective switch on the key pad.

F.“Valve Fault”- Faulty Valve Detection: When an electric or switching problem is detected with either the inlet or brew valve the brewer turns off all elements and valves and displays “valve fault…”. All of the lights will be turned on. Before re-setting the brewer the valves must be checked to determine the problem. The brewer must be re-energized to re-set, (pressing CANCEL for 3 seconds will not reset a valve fault).

10

Page 11 Page 13
Image 12
Page 11 Page 13
Contents 653 Warranty Statement Table of Contents SpecificationsFeatures and Operating Controls Precautions and General Information Electrical DamageInstallation Instructions PLUMBER’S Installation InstructionsEquipment Hazard Unpacking & Initial InspectionInstallation Instructions ELECTRICIAN’S Installation InstructionsOperation Operating InstructionsOperation Burn HazardProgramming Features and Options Clock Operation Cleaning Instructions Electric Shock HazardServicing Instructions Plumbing FunctionServicing Instructions Plumbing Description Part N0 Used onServicing Instructions Electrical Risk of InjuryServicing Instructions Electrical Servicing Instructions DE-LIMING Heater Tank Burn HazardTroubleshooting Suggestions Cause Suggestions for Remedial ActionEntering Test Program Mode Max T Test ProgramCheck Data Revision TimeBrew Cancel ON/OFF Exploded View & Parts List Exploded View & Parts List Wiring Diagrams Page Telephone Fax

2030 specifications

Bloomfield 2030 is an ambitious vision for the future of urban living, focusing on sustainability, connectivity, and enhanced quality of life for its residents. This forward-thinking initiative aims to transform Bloomfield into a model smart city, integrating advanced technologies and innovative practices to create a vibrant community.

One of the main features of Bloomfield 2030 is its commitment to sustainability. The city plans to implement green infrastructure, including extensive urban parks, green roofs, and vertical gardens. These initiatives will promote biodiversity, improve air quality, and reduce urban heat. Additionally, renewable energy sources such as solar and wind power will be harnessed to meet the city's energy needs, with the goal of achieving net-zero emissions by 2030.

Another key characteristic of Bloomfield 2030 is its focus on smart technology. The city will leverage Internet of Things (IoT) devices to enhance urban services and improve the overall efficiency of municipal operations. Smart traffic management systems will optimize traffic flow and reduce congestion, while connected sensors will monitor air quality and noise levels to help maintain a healthy environment. Public safety will be enhanced through the use of smart surveillance and emergency response systems, ensuring residents feel secure in their community.

In addition to environmental and technological advancements, Bloomfield 2030 places a strong emphasis on community engagement and inclusivity. The city plans to incorporate citizen feedback into urban planning initiatives, fostering a sense of ownership and belonging among residents. Diverse housing options, including affordable units and co-housing projects, will cater to a wide range of demographics, ensuring that all community members have access to quality living conditions.

Transportation will also undergo significant transformations under the Bloomfield 2030 plan. The city aims to promote active transportation methods, such as walking and cycling, by developing extensive bike lanes and pedestrian pathways. Additionally, a robust public transit system will connect different neighborhoods, reducing reliance on personal vehicles and lowering carbon emissions.

In summary, Bloomfield 2030 represents a futuristic vision of urban development that prioritizes sustainability, smart technology, community involvement, and efficient transportation. By embracing these principles, Bloomfield will create a thriving, inclusive, and resilient city that meets the needs of its residents while protecting the environment for future generations.
Top Page Image Contents