Servicing Instructions DE-LIMING Heater Tank

SERVICING INSTRUCTIONS — DE-LIMING HEATER TANK

CAUTION - CHEMICAL

BURN HAZARD

De-liming chemicals are caustic. Wear appropriate protective gloves and goggles during this procedure.

CAUTION - CHEMICAL

BURN HAZARD

Never siphon de-liming chemicals or solutions by mouth.

This operation must only be performed by qualified and experienced service personnel.

IMPORTANT: DO NOT spill, splash or pour water or de-liming solution into or over any internal component other than the inside of the water tank.

IMPORTANT: DO NOT allow any internal components to come into contact with the de-liming solution. Take care to keep all internal components dry.

NOTE: Repeat steps 4 thru 7 as required to remove all scale and lime build-up.

NOTE: Normally, silicone hoses do not need to be de-limed. Should de-liming hoses become necessary, Bloomfield Industries recommends replacing the hoses.

1.Disconnect brewer form the electrical supply. Turn off the water supply and disconnect water supply from the brewer inlet fitting.

2.Remove the top panel to gain access to internal components.

3.Disconnect water level sensor and water temperature sensor from the controller. On 120V units, slip hi-limit thermostat from under its holder clip. Disassemble the three lid clips and lift the lid off of the water tank. Store lid assembly in a safe location.

4.Mix de-liming solution according to the manufacturer’s directions. Add the de-liming solution to the water tank. Set lid assembly back on tank. Allow to sit for 30 minutes, or as directed by the manufacturer.

5.At end of soaking period, remove lid assembly from tank. Thoroughly rinse interior components of lid assembly with clear water. Wipe temperature sensor and water level sensor with a clean, soft cloth. Store lid assembly in a safe location.

6.Using a stiff bristle brush, scrub the coils of the heating element and the interior surfaces of the water tank.

7.Siphon the used solution and loose lime/scale into an appropriate container. Dispose of the used solution as required by local ordinances.

CAUTION: Never siphon by mouth. Serious injury can result!

8.Fill the water tank with clean tap water. Rinse thoroughly, then siphon the rinse water into an appropriate container for disposal. Again, take care to keep all internal components dry.

9.Reassemble the tank lid to the water tank. Make sure the gasket is properly attached to the lid before assembling the lid clips. Re-connect the water level and temperature probes, then reinstall the hi-limit thermostat (if removed). Verify that all internal components are dry, then reinstall the top panel.

10.Reconnect brewer to water and electrical. Run and discard at least three full decanters from the faucet. Install the brew chamber without filter paper or grounds, then run and discard at least three full decanters as normal brew.

11.Brewer is ready to use.

2030 specifications

Bloomfield 2030 is an ambitious vision for the future of urban living, focusing on sustainability, connectivity, and enhanced quality of life for its residents. This forward-thinking initiative aims to transform Bloomfield into a model smart city, integrating advanced technologies and innovative practices to create a vibrant community.

One of the main features of Bloomfield 2030 is its commitment to sustainability. The city plans to implement green infrastructure, including extensive urban parks, green roofs, and vertical gardens. These initiatives will promote biodiversity, improve air quality, and reduce urban heat. Additionally, renewable energy sources such as solar and wind power will be harnessed to meet the city's energy needs, with the goal of achieving net-zero emissions by 2030.

Another key characteristic of Bloomfield 2030 is its focus on smart technology. The city will leverage Internet of Things (IoT) devices to enhance urban services and improve the overall efficiency of municipal operations. Smart traffic management systems will optimize traffic flow and reduce congestion, while connected sensors will monitor air quality and noise levels to help maintain a healthy environment. Public safety will be enhanced through the use of smart surveillance and emergency response systems, ensuring residents feel secure in their community.

In addition to environmental and technological advancements, Bloomfield 2030 places a strong emphasis on community engagement and inclusivity. The city plans to incorporate citizen feedback into urban planning initiatives, fostering a sense of ownership and belonging among residents. Diverse housing options, including affordable units and co-housing projects, will cater to a wide range of demographics, ensuring that all community members have access to quality living conditions.

Transportation will also undergo significant transformations under the Bloomfield 2030 plan. The city aims to promote active transportation methods, such as walking and cycling, by developing extensive bike lanes and pedestrian pathways. Additionally, a robust public transit system will connect different neighborhoods, reducing reliance on personal vehicles and lowering carbon emissions.

In summary, Bloomfield 2030 represents a futuristic vision of urban development that prioritizes sustainability, smart technology, community involvement, and efficient transportation. By embracing these principles, Bloomfield will create a thriving, inclusive, and resilient city that meets the needs of its residents while protecting the environment for future generations.