Bloomfield 2030 owner manual ELECTRICIAN’S Installation Instructions

Page 7

INSTALLATION INSTRUCTIONS (continued)

5.NSF requires that the brewer be able to be moved for cleaning underneath. Loops of copper tubing will satisfy this requirement.

COPPER LOOPS

 

(PROVIDED BY PLUMBER)

 

SHUT-OFF VALVE

SOLENOID

STRAINER

(PROVIDED BY

WASHER

PLUMBER)

 

FLOW

WATER

SUPPLY

6.In some areas, local codes require a backflow preventer (check valve) to be installed on the inlet water line. If a back flow preventer is used, you must install a water hammer arrester in the incoming line, between the backflow preventer and the brewer inlet, as far away from the brewer as space will allow. This will relieve the excessive back pressures that can cause faucet leaks and solenoid malfunctions.

ELECTRICIAN’S INSTALLATION INSTRUCTIONS

REFER TO ELECTRICAL SPECIFICATIONS - Page 1

Check the nameplate to determine correct electrical service required for the Brewer to be installed.

NOTE: Models 2030 requires a 115 - 125 V 15A circuit (50/60 Hz, 2 wire plus earth ground, with NEMA 5-15R or 5-20R Receptacle)

AGENCY LISTING INFORMATION

This brewer is

and

listed under UL file E9253.

This brewer meets

 

Standard 4 only when installed,

operated and maintained in accordance with the enclosed instructions.

NOTE: This equipment must be installed to comply with applicable federal, state and local plumbing codes and ordinances.

WARNING ELECTRIC SHOCK HAZARD:

Brewer must be properly grounded to prevent possible shock hazard. DO NOT assume a plumbing line will provide such a ground. Electrical shock will cause death or serious injury.

IMPORTANT: Do not attempt to override the automatic tank fill feature which requires that the tank must be full of water to start operations. Any attempt to override this feature will void the warranty.

IMPORTANT:

Before connecting to electricity, make sure the E-Max™ has been properly connected to the water supply.

IMPORTANT:

Supply power must match nameplate for voltage and phase. Connecting to the wrong voltage will damage the brewer or result in decreased performance. Such damage is not covered by warranty.

E9253

E9253

STD 4

5

Page 6 Page 8
Image 7
Page 6 Page 8
Contents 653 Warranty Statement Specifications Table of ContentsFeatures and Operating Controls Electrical Damage Precautions and General InformationUnpacking & Initial Inspection Installation InstructionsPLUMBER’S Installation Instructions Equipment HazardELECTRICIAN’S Installation Instructions Installation InstructionsOperating Instructions OperationBurn Hazard OperationProgramming Features and Options Clock Operation Electric Shock Hazard Cleaning InstructionsFunction Servicing Instructions PlumbingDescription Part N0 Used on Servicing Instructions PlumbingRisk of Injury Servicing Instructions ElectricalServicing Instructions Electrical Burn Hazard Servicing Instructions DE-LIMING Heater TankCause Suggestions for Remedial Action Troubleshooting SuggestionsTime Entering Test Program ModeMax T Test Program Check Data RevisionBrew Cancel ON/OFF Exploded View & Parts List Exploded View & Parts List Wiring Diagrams Page Telephone Fax

2030 specifications

Bloomfield 2030 is an ambitious vision for the future of urban living, focusing on sustainability, connectivity, and enhanced quality of life for its residents. This forward-thinking initiative aims to transform Bloomfield into a model smart city, integrating advanced technologies and innovative practices to create a vibrant community.

One of the main features of Bloomfield 2030 is its commitment to sustainability. The city plans to implement green infrastructure, including extensive urban parks, green roofs, and vertical gardens. These initiatives will promote biodiversity, improve air quality, and reduce urban heat. Additionally, renewable energy sources such as solar and wind power will be harnessed to meet the city's energy needs, with the goal of achieving net-zero emissions by 2030.

Another key characteristic of Bloomfield 2030 is its focus on smart technology. The city will leverage Internet of Things (IoT) devices to enhance urban services and improve the overall efficiency of municipal operations. Smart traffic management systems will optimize traffic flow and reduce congestion, while connected sensors will monitor air quality and noise levels to help maintain a healthy environment. Public safety will be enhanced through the use of smart surveillance and emergency response systems, ensuring residents feel secure in their community.

In addition to environmental and technological advancements, Bloomfield 2030 places a strong emphasis on community engagement and inclusivity. The city plans to incorporate citizen feedback into urban planning initiatives, fostering a sense of ownership and belonging among residents. Diverse housing options, including affordable units and co-housing projects, will cater to a wide range of demographics, ensuring that all community members have access to quality living conditions.

Transportation will also undergo significant transformations under the Bloomfield 2030 plan. The city aims to promote active transportation methods, such as walking and cycling, by developing extensive bike lanes and pedestrian pathways. Additionally, a robust public transit system will connect different neighborhoods, reducing reliance on personal vehicles and lowering carbon emissions.

In summary, Bloomfield 2030 represents a futuristic vision of urban development that prioritizes sustainability, smart technology, community involvement, and efficient transportation. By embracing these principles, Bloomfield will create a thriving, inclusive, and resilient city that meets the needs of its residents while protecting the environment for future generations.
Top Page Image Contents