Bloomfield 2030 Max T Test Program, Entering Test Program Mode, Check Data Revision, Time

Page 20

E-Max T™ TEST PROGRAM

Remember: Exiting Test Program Mode: To exit the Test Program, press the 2nd key (Cancel) at any time, except during the key switch tests below. Alternately, complete the full test and the E-Max T™ will return to the OFF mode.

Note: each key press should be followed by an audible beep.

Note: Bloomfield recommends that, should the keypad fail a test, the test be carefully repeated at least three times to verify the keypad failure.

Instructions for testing procedures for the following system components (using the E-Max T™ Built-In Diagnostic):

Electronic Board Software (Firmware) Revision Keypad switches

LED’s

Inlet valve, Dump (Brew) valve, By Pass Valve Water level probe, Temperature probe

A.Entering Test Program Mode:

1.Make sure to have power to the system. Press the 3rd key to enter the OFF mode.

2.In the Off mode, hold down the 3rd (ON/OFF) and 4th keys (1st volume key or “E” in “E-Max T”). Hold both keys down for approximately 3 seconds.

If successful, a message containing the revision of the firmware will be displayed: (e.g. “MFW275T Rev 1.2”)

3.Press the 3rd key.

B.Check Data Revision

1.The next display contains the revision number of the data programmed into the EEPROM: (e.g. “Data Rev1.2”).

2.Press the 3rd key to continue.

C.Time

Time is preset

D.Switch Test - The keys are tested in this stage.

1.Test 1st key by pressing the “BREW” key. You will hear a beep, and the display will change to “Test Switch 2”.

2.Test 2nd key by pressing the “CANCEL” key. You will hear a beep, and the display will change to “Test Switch 3”

3.Test the 3rd key by pressing the “ON/OFF” key. You will hear a beep, and the display will change to “Test Switch 4”

4.Continue by pressing the 4th key (1st volume key, or “E” in "E-Max T');

5.5th key (2nd volume key, or “a” in "E-Max T"); and,

6.6th key (3rd volume key, or “T” in "E-Max T")

Except for Switch 1, if a key press is not detected within five seconds, the “Switch Error” message Will be displayed followed by two beeps. For Switch 1, the time limit is 30 seconds.

If an error occurs when the correct key is pressed, the keypad has failed the test.

18

Image 20
Contents 653 Warranty Statement Table of Contents SpecificationsFeatures and Operating Controls Precautions and General Information Electrical DamageInstallation Instructions PLUMBER’S Installation InstructionsEquipment Hazard Unpacking & Initial InspectionInstallation Instructions ELECTRICIAN’S Installation InstructionsOperation Operating InstructionsOperation Burn HazardProgramming Features and Options Clock Operation Cleaning Instructions Electric Shock HazardServicing Instructions Plumbing FunctionServicing Instructions Plumbing Description Part N0 Used onServicing Instructions Electrical Risk of InjuryServicing Instructions Electrical Servicing Instructions DE-LIMING Heater Tank Burn HazardTroubleshooting Suggestions Cause Suggestions for Remedial ActionEntering Test Program Mode Max T Test ProgramCheck Data Revision TimeBrew Cancel ON/OFF Exploded View & Parts List Exploded View & Parts List Wiring Diagrams Page Telephone Fax

2030 specifications

Bloomfield 2030 is an ambitious vision for the future of urban living, focusing on sustainability, connectivity, and enhanced quality of life for its residents. This forward-thinking initiative aims to transform Bloomfield into a model smart city, integrating advanced technologies and innovative practices to create a vibrant community.

One of the main features of Bloomfield 2030 is its commitment to sustainability. The city plans to implement green infrastructure, including extensive urban parks, green roofs, and vertical gardens. These initiatives will promote biodiversity, improve air quality, and reduce urban heat. Additionally, renewable energy sources such as solar and wind power will be harnessed to meet the city's energy needs, with the goal of achieving net-zero emissions by 2030.

Another key characteristic of Bloomfield 2030 is its focus on smart technology. The city will leverage Internet of Things (IoT) devices to enhance urban services and improve the overall efficiency of municipal operations. Smart traffic management systems will optimize traffic flow and reduce congestion, while connected sensors will monitor air quality and noise levels to help maintain a healthy environment. Public safety will be enhanced through the use of smart surveillance and emergency response systems, ensuring residents feel secure in their community.

In addition to environmental and technological advancements, Bloomfield 2030 places a strong emphasis on community engagement and inclusivity. The city plans to incorporate citizen feedback into urban planning initiatives, fostering a sense of ownership and belonging among residents. Diverse housing options, including affordable units and co-housing projects, will cater to a wide range of demographics, ensuring that all community members have access to quality living conditions.

Transportation will also undergo significant transformations under the Bloomfield 2030 plan. The city aims to promote active transportation methods, such as walking and cycling, by developing extensive bike lanes and pedestrian pathways. Additionally, a robust public transit system will connect different neighborhoods, reducing reliance on personal vehicles and lowering carbon emissions.

In summary, Bloomfield 2030 represents a futuristic vision of urban development that prioritizes sustainability, smart technology, community involvement, and efficient transportation. By embracing these principles, Bloomfield will create a thriving, inclusive, and resilient city that meets the needs of its residents while protecting the environment for future generations.