Merco Savory C-40 On/Off Switch Replacement, Bun/Toast Switch Replace- ment, Refer to Figure #3

Page 2

IMPORTANT

Disconnect power before attempting service or disassembling components.

Servicing: All electrical and drive components are accessible for servicing by removal of the right side panel. Remove the two screws from underside of panel and pull handle to release.

A On/Off Switch Replacement:

1.Remove right side panel.

2.Remove two retaining screws from front panel.

3.Disconnect wiring harness from switch terminals.

4.Connect wiring harness to new switch and install switch in panel. Refer to wiring diagram.

BBun/Toast Switch Replace- ment:

1.Remove right side panel.

2.Disconnect wiring harness from switch terminals.

3.Depress two spring clips on top of switch and tilt switch forward.

4.Insert the new switch into the panel opening, snapping snugly into place.

5.Reconnect the wiring harness to the terminals. Refer to wiring diagram.

C Thermostat Replacement:

(Refer to Figure #3)

1.Remove left and right side panels.

2.Remove insulation

NOTE: The wiring harness must be disconnected from heating elements to remove insulation on right side. Hold terminals with pliers to prevent bending. (Figure #4)

3.Remove rear heating element. (Refer to Section D)

4.Remove wire guard. (Refer to Section O)

5.Remove two baskets from conveyor chain, then rotate the chain so that this opening is at the bottom directly under the thermostat bulb.

6.Pull off thermostat knob.

7.Remove the two retaining screws from front panel.

8.Remove wires from thermostat.

9.Push as much capillary tube as possible through the plastic grommet located on the upper portion above the shelf and pull thermostat bulb out of the hole.

10.Feed capillary tube and bulb through plastic grommet into the lower portion below shelf and remove from toaster.

11.To install new thermostat, feed bulb and tube through bottom of plastic grommet.

CAUTION: Avoid sharp bends or kinks in the capillary tube as this will create restrictions preventing proper thermostat operation.

12.Insert bulb into hole and through center guide. The bulb can be seen through the openings for the wire guard and read heater element.

13.Push bulb through hole in left side inner panel. It can be manually guided by reaching through rear delivery opening and up through opening in conveyor where baskets have been removed. Bulb should be extended about 1-1/2” from left inner panel.

14.Attach wires to thermostat. (Refer to wiring diagram)

2

Image 2
Contents Parts & Service for C-40VS/C-40 Vertical Conveyor Toaster Thermostat Replacement On/Off Switch ReplacementBun/Toast Switch Replace- ment Refer to Figure #3Heater Unit Assembly Re- placement Refer to Figure #5208V-21107 240V-21109 Individual Heater Element ReplacementMotor Replacement Refer to , 9 & 9ABearing Replacement Drive Chain ReplacementHubbed Sprocket Replacement Clutch Sprocket Replace- mentConveyor Chain Replace- ment Refer to Figure #11 Transmission Assembly Re- placementTension Assembly Replace- ment Coupling Assembly Re- placement Refer to Figure #22 Wire Guard ReplacementRefer to Figure #21 Page Page North Hadley Road Fort Wayne, Technical Service Hotline

C-40 specifications

The Merco Savory C-40 is a state-of-the-art cooking and holding unit designed for commercial kitchens looking to elevate their food service operations. Engineered for versatility and efficiency, the C-40 integrates advanced technologies that cater specifically to the needs of busy kitchens, ensuring that meals are cooked and held at optimal quality for customers.

One of the main features of the Merco Savory C-40 is its advanced cooking system, which utilizes a combination of convection and direct heat to deliver superior cooking results. This dual method not only ensures even cooking but also enables chefs to achieve the perfect texture and flavor across a diverse range of menu items, from roasted meats to baked goods.

The C-40 boasts an impressive capacity, allowing operators to cook and hold multiple dishes simultaneously. Its expansive cooking chamber is designed to accommodate various pan sizes, making it perfect for high-demand environments. With the ability to cook large quantities at once, it streamlines kitchen operations and reduces overall cooking times.

In addition to its cooking capabilities, the Merco Savory C-40 features an innovative holding system that maintains optimal temperatures and humidity levels. This technology is ideal for keeping cooked foods at serving temperatures for extended periods without compromising quality. The precise temperature controls allow chefs to set the desired holding temperature, ensuring food remains fresh and ready to serve whenever needed.

Another key characteristic of the C-40 is its user-friendly interface. The digital controls provide instant access to cooking settings, timers, and temperature adjustments. This enhances operational efficiency and minimizes the learning curve for kitchen staff, making it easy for everyone to utilize the unit effectively.

Durability is also a hallmark of the Merco Savory C-40. Constructed from high-quality stainless steel, it is built to withstand the rigors of a commercial kitchen environment. The robust design ensures longevity while also simplifying cleaning and maintenance, vital for busy culinary operations.

Overall, the Merco Savory C-40 combines functionality, advanced technologies, and a focus on food quality, making it an essential addition for any professional kitchen aiming to enhance service and streamline their cooking processes. Its blend of innovative features and user-friendly design empowers chefs to deliver exceptional meals consistently, benefiting both the kitchen staff and the customers they serve.