Maytag W10649077A Drain Requirements, Water Supply Requirements, Electrical Requirements

Page 6

Drain Requirements

■A new drain hose is supplied with your dishwasher. If drain hose is not long enough, use a new drain hose with a maximum length of 12 ft (3.7 m) (Part Number 3385556) that meets all current AHAM/IAPMO test standards, is resistant to heat and detergent, and fits the 1" (2.5 cm) drain connector of the dishwasher.

■Make sure to connect drain hose to waste tee or disposer inlet above drain trap in house plumbing and 20" (50.8 cm) minimum above the floor. It is recommended that the drain hose either be looped up and securely fastened to the underside of the counter, or be connected to an air gap.

■Make sure to use an air gap if the drain hose is connected to house plumbing lower than 20" (50.8 cm) above subfloor or floor.

■Use ¹ " minimum I.D. drain line fittings.

■If required, the air gap should be installed in accordance with the air gap installation instructions. When you are connecting the air gap, a rubber hose (not provided) will be needed to connect to the waste tee or disposer inlet.

Water Supply Requirements

■A hot water line with 20 to 120 psi (138 to 862 kPa) water pressure can be verified by a licensed plumber.

■120°F (49°C) water at dishwasher.

■³⁄₈" O.D. copper tubing with compression fitting or flexible braided water supply line (Part Number W10278635RP). NOTE: ¹⁄₂" minimum plastic tubing is not recommended.

■A 90° elbow with ³⁄₄" hose connection with rubber washer (Part Number W10574777).

■Do not solder within 6" (15.2 cm) of the water inlet valve.

Electrical Requirements

Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/NFPA 70 - latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association 1 Batterymarch Park

Quincy, MA 02169-7471

You must have:

■120-volt, 60 Hz, AC-only, 15- or 20-amp, fused electrical supply.

■Copper wire only.

We recommend:

■A time-delay fuse or circuit breaker.

■A separate circuit.

If connecting dishwasher with a power supply cord:

■ Use UL Listed power supply cord kit (Part Number 4317824) marked for use with dishwasher.

■Power supply cord must plug into a grounded

3 prong outlet, located in the cabinet next to the dishwasher opening. Outlet must meet all local codes and ordinances.

If connecting dishwasher with direct wiring:

■Use flexible, armored or nonmetallic

sheathed, copper wire with grounding wire that meets the wiring requirements for your home and local codes and ordinances.

■Use a UL Listed/CSA Approved strain relief.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Instructions Dinstallation Table of Contents Dishwasher SafetyAddition, for first-time installations Installation RequirementsAll Installations Tools and PartsLocation Requirements Page Drain Requirements If connecting dishwasher with a power supply cordIf connecting dishwasher with direct wiring Water Supply RequirementsInstallation Instructions Prepare Cabinet Opening-New UtilitiesOption B, Direct Wire Prepare and Route Water LineInstall Drain Hose Option A, Waste disposer no air gap Option B, No waste disposer no air gapOption C, Waste disposer with air gap Prepare Dishwasher Option D, No waste disposer with air gapOption A, Remove Access Panel Plastic Panel Option B, Remove Access Panel Metal PanelMake Power Supply Cord Connection Determine Cabinet Opening Choose Attachment Option Option A, Countertop AttachmentMove Dishwasher Close to Cabinet Opening Page Connect to Water Supply Connect to Drain Make Direct Wire Electrical Connection Secure Dishwasher in Cabinet Opening Secure dishwasher to countertop Side mount dishwasher to cabinetComplete Installation If Dishwasher Does Not Operate Reconnect PowerCheck Operation Additional TipsTable DES Matières Sécurité DU LAVE-VAISSELLEIl faut Exigences Dinstallation Toutes les installationsOutillage et pièces Exigences demplacement Page Exigences d’évacuation Spécifications électriquesPour le raccordement direct du lave-vaisselle Nouveaux moyens de raccordement Instructions DinstallationMoyens de raccordement préexistants Préparation et acheminement de l’alimentation électriquePréparation et acheminement de la canalisation d’eau Option B, raccordement directInstallation du tuyau d’évacuation Option A, Broyeur à déchets sans brise-siphon Option B, Pas de broyeur à déchets sans brise-siphonOption C, Broyeur à déchets avec brise-siphon Préparation du lave-vaisselle Option D, Pas de broyeur à déchets avec brise-siphonOption a Retrait du panneau daccès Panneau en plastique Option B Retrait du panneau daccès Panneau métalliqueRaccordement du cordon dalimentation Évaluation de l’ouverture dencastrement du placard Choix de l’option de fixation Option A, Fixation au plan de travailLouverture dencastrement du placard Remarques Raccordement à l’alimentation en eau Raccordement au circuit dévacuation Raccordement électrique direct Page Fixation du lave-vaisselle au plan de travail Fixation latérale du lave-vaisselle au placardAchever linstallation Option B Installation du panneau daccès Panneau métalliqueContrôle du fonctionnement Si le lave-vaisselle ne fonctionne pasRétablir la source de courant électrique Conseils supplémentaires W10649077A

W10649077A specifications

The Maytag W10649077A is an innovative appliance designed to meet the needs of modern kitchens while providing unmatched reliability and performance. This model is particularly noteworthy for its advanced features and technologies that cater to user convenience and superior cleaning capabilities.

One of the standout features of the Maytag W10649077A is its robust construction, built with stainless steel components that not only enhance its durability but also provide a sleek aesthetic that fits well in any kitchen decor. This model includes a spacious interior, allowing for the effective organization of dishes, pots, and utensils, accommodating everything from everyday dishes to larger cookware.

The incorporation of PowerBlast technology significantly improves the cleaning performance of this appliance. This powerful feature utilizes pressurized jets, increased heat, and heightened wash action to remove stubborn food particles and residues, ensuring every dish comes out sparkling clean. This technology is especially effective against dried-on or baked-on food, making it an ideal choice for hard-working households.

In terms of energy efficiency, the Maytag W10649077A boasts an Energy Star rating, reflecting its commitment to reducing energy consumption without sacrificing performance. This model is designed to minimize water usage while maximizing the effectiveness of each wash cycle, contributing to lower utility bills and a more eco-friendly home.

Another noteworthy characteristic is the noise reduction technology implemented in this model. The Maytag W10649077A operates quietly, making it suitable for open-concept homes or late-night use without disturbing the household's peace. This feature allows users to run the dishwasher without the annoyance of loud operational sounds.

The user interface of the Maytag W10649077A is designed for simplicity and ease of use. It features intuitive controls that allow users to select from multiple wash cycles and customize settings tailored to their specific cleaning needs. Whether it’s a quick wash for lightly soiled items or an intensive cycle for heavily soiled pots and pans, this appliance delivers versatility for all dishwashing scenarios.

In summary, the Maytag W10649077A stands out in the crowded appliance market due to its advanced features, durability, energy efficiency, and user-friendly design. This model exemplifies Maytag's commitment to quality and innovation, making it a reliable choice for consumers seeking a powerful and efficient dishwasher capable of handling the demands of any kitchen.
Top Page Image Contents