Maytag W10532762A Drain Requirements, Water Supply Requirements, Electrical Requirements

Page 6

Drain Requirements

■A new drain hose is supplied with your dishwasher. If drain hose is not long enough, use a new drain hose with a maximum length of 12 ft (3.7 m) (Part Number 3385556) that meets all current AHAM/IAPMO test standards, is resistant to heat and detergent, and fits the 1" (2.5 cm) drain connector of the dishwasher.

■Make sure to connect drain hose to waste tee or disposer inlet above drain trap in house plumbing and 20" (50.8 cm) minimum above the floor. It is recommended that the drain hose either be looped up and securely fastened to the underside of the counter, or be connected to an air gap.

■Make sure to use an air gap if the drain hose is connected to house plumbing lower than 20" (50.8 cm) above subfloor or floor.

■Use ¹ " minimum I.D. drain line fittings.

■If required, the air gap should be installed in accordance with the air gap installation instructions. When you are connecting the air gap, a rubber hose (not provided) will be needed to connect to the waste tee or disposer inlet.

Water Supply Requirements

■A hot water line with 20 to 120 psi (138 to 862 kPa) water pressure can be verified by a licensed plumber.

■120°F (49°C) water at dishwasher.

■³⁄₈" O.D. copper tubing with compression fitting or flexible braided water supply line (Part Number 4396897RP). NOTE: ¹⁄₂" minimum plastic tubing is not recommended.

■A 90° elbow with ³⁄₄" hose connection with rubber washer.

■Do not solder within 6" (15.2 cm) of the water inlet valve.

Electrical Requirements

Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/NFPA 70 - latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association 1 Batterymarch Park

Quincy, MA 02169-7471

You must have:

■120-volt, 60 Hz, AC-only, 15- or 20-amp, fused electrical supply.

■Copper wire only.

We recommend:

■A time-delay fuse or circuit breaker.

■A separate circuit.

If connecting dishwasher with a power supply cord:

■ Use UL Listed power supply cord kit (Part Number 4317824) marked for use with dishwasher.

■Power supply cord must plug into a grounded

3 prong outlet, located in the cabinet next to the dishwasher opening. Outlet must meet all local codes and ordinances.

If connecting dishwasher with direct wiring:

■Use flexible, armored or nonmetallic

sheathed, copper wire with grounding wire that meets the wiring requirements for your home and local codes and ordinances.

■Use a UL Listed/CSA Approved strain relief.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents W10532762A Table of Contents Dishwasher SafetyAddition, for first-time installations Installation RequirementsAll Installations Tools and PartsLocation Requirements Page Drain Requirements If connecting dishwasher with a power supply cordIf connecting dishwasher with direct wiring Water Supply RequirementsInstallation Instructions Prepare Cabinet Opening-Existing UtilitiesPrepare Cabinet Opening-New Utilities Option B, Direct Wire Prepare and Route Water LineInstall Drain Hose Option A, Waste disposer no air gap Option B, No waste disposer no air gapOption C, Waste disposer with air gap Prepare Dishwasher Option D, No waste disposer with air gapPage Make Power Supply Cord Connection Determine Cabinet Opening Choose Attachment Option Option 1, Countertop AttachmentMove Dishwasher Close to Cabinet Opening Page Connect to Water Supply Connect to Drain Make Direct Wire Electrical Connection Secure Dishwasher in Cabinet Opening Secure dishwasher to countertop Side mount dishwasher to cabinetComplete Installation Reconnect PowerCheck Operation If Dishwasher Does Not OperateAdditional Tips Table DES Matières Sécurité DU LAVE-VAISSELLEIl faut Exigences Dinstallation Toutes les installationsOutillage et pièces Exigences demplacement Page Spécifications électriques Exigences d’évacuationSpécifications de l’alimentation en eau Pour le raccordement direct du lave-vaisselleInstructions Dinstallation Préparation et acheminement de l’alimentation électriqueOption A, cordon d’alimentation Préparation et acheminement de la Canalisation d’eau Option B, raccordement directInstallation du tuyau d’évacuation Option a broyeur à déchets sans brise-siphon Option B pas de broyeur à déchets sans brise-siphonOption C broyeur à déchets avec brise-siphon Préparation du lave-vaisselle Option D pas de broyeur à déchets avec brise-siphonPage Raccordement du cordon dalimentation Évaluation de l’ouverture dencastrement du placard Choix de l’option de fixation Option 1, Fixation au plan de travailAvertissement Remarques Raccordement à l’alimentation en eau Raccordement au circuit dévacuation Raccordement électrique direct Page Fixation du lave-vaisselle au plan de travail Fixation latérale du lave-vaisselle au placardAchever linstallation Rétablir la source de courant électriqueContrôle du fonctionnement Si le lave-vaisselle ne fonctionne pasConseils supplémentaires W10532762A

W10532762A specifications

The Maytag W10532762A is a innovative appliance designed to enhance the efficiency and effectiveness of laundry processes, standing out in the competitive landscape of washer and dryer technologies. This model incorporates several advanced features tailored to meet the demands of modern households, ensuring that laundry days are less of a chore and more streamlined.

One of the standout features of the Maytag W10532762A is its powerful Agitator. The design of the agitator is engineered to deliver a robust washing performance by providing maximum cleaning action, ensuring that tough stains are removed efficiently while protecting fabrics. This means that even the most heavily soiled clothes can be cleaned thoroughly, saving time and effort in the process.

Another significant characteristic is the large capacity drum, which allows users to wash larger loads in a single cycle. This is particularly beneficial for families or individuals who have frequent laundry needs, as it reduces the number of cycles required, ultimately saving both time and energy. The machine's design also incorporates strategic placement of wash basket to reduce friction and minimize wear on fabrics.

The Maytag W10532762A also employs advanced washing technology with its PowerWash cycle. This feature is designed to tackle tough stains and deliver a thorough clean, ensuring that laundry comes out fresher and cleaner than ever. This cycle is complemented by a selection of customizable wash settings, allowing users to choose the best option for their specific laundry needs.

For efficiency and energy savings, the Maytag W10532762A is built with energy-saving features, such as a high-efficiency water usage design. This ensures that the appliance uses only the necessary amount of water, helping to conserve resources without compromising performance.

Additionally, the machine is designed with durability in mind. It comes equipped with robust components, providing users the peace of mind that their investment will stand the test of time, even with frequent use. Maytag’s reputation for reliability is well-reflected in this model, making it a valuable addition to any laundry room.

In summary, the Maytag W10532762A combines powerful cleaning capabilities, large capacity, advanced technologies, and energy efficiency, making it a top choice for anyone looking to enhance their laundry experience while ensuring that their clothes are treated with care. With the integration of smart features and a user-friendly design, it’s positioned as a leader in modern washing appliances.
Top Page Image Contents