Maytag W10191953A installation instructions Assistance, Replacement Parts, Accessories

Page 12

Recommended Vent Length

A 3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular or 6" (15.2 cm) round vent

6" (15.2 cm) vent system = 73 ft (22.2 m) total

should be used.

 

The total length of the vent system including straight vent, elbow(s), transitions and wall or roof caps must not exceed the equivalent of 140 ft (42.7 m) for either type of vent. See “Recommended Standard Fittings” section for equivalent lengths.

For best performance, use no more than three 90° elbows.

To calculate the length of the system you need, add the equivalent lengths of each vent piece used in the system. See the following examples:

3¹⁄₄" x 10" (8.3 x 25.4 cm) vent system = 73 ft (22.2 m) total

AB

6 ft (1.8 m)

A

2 ft

(0.6 m)

C

B

6 ft (1.8 m)

D

2ft

(0.6 m)

A. Two 90° elbows = 20 ft (6.1 m) B. 1 wall cap = 40 ft (12.2 m)

C. 1 rectangular to round transition piece = 5 ft (1.5 m) D. 2 ft (0.6 m) + 6 ft (1.8 m) straight = 8 ft (2.4 m)

C

A. One 3¹⁄₄" x 10" (8.3 x 25.4 cm) 90° elbow = 25 ft (7.6 m) B. 1 wall cap = 40 ft (12.2 m)

C. 2 ft (0.6 m) + 6 ft (1.8 m) straight = 8 ft (2.4 m)

If the existing vent is round, a rectangular to round transition piece must be used. In addition, a rectangular 3" (7.6 cm) extension vent between the damper assembly and rectangular to round transition piece must be installed to keep the damper from sticking.

ASSISTANCE

Call your authorized dealer or service center. When you call, you will need the microwave oven model number and serial number. Both numbers can be found on the model and serial number plate, which is located behind the microwave oven door on the front frame of the microwave oven.

If you need additional assistance, call us at our toll free number or visit our website listed in the Use and Care Guide.

Replacement Parts

If any of the installation hardware needs to be replaced, call us at our toll free number listed in the User Instructions.

Following is a list of available replacement parts. You will need your model number located on the front facing of the microwave oven opening, behind the door.

■Damper Assembly

■Mounting Plate

■Upper Cabinet Template

■Mounting Screw Kit (includes parts A-G in “Parts Supplied” in the “Tools and Parts” section)

Accessories

Filler Panel Kits are available from your dealer to use when installing this microwave oven in a 36" (91.4 cm) or 42" (106.7 cm) wide opening. The filler panels come in pairs. Each panel is 3" (7.6 cm) wide.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A. Filler panels

 

Filler Panel Kit Number 8171336

White

 

8171337

Black

 

8171338

Biscuit

 

8171339

Stainless Steel

 

99403

 

Almond

 

See your authorized dealer or service center for details.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Microwave Hood Combination Installation Instructions Microwave Hood Combination SafetyInstallation Requirements Tools and PartsRemove Cardboard Template Location RequirementsProduct Dimensions Electrical Requirements Installation DimensionsObserve all governing codes and ordinances RequiredInstallation Instructions Wall Venting Installation OnlyRemove Mounting Plate Rotate Blower MotorRoof Venting Installation Only Secure damper plate with 2 screws removed in StepPossible Wall Stud Configurations Locate Wall StudsNo Wall Studs at End Holes Wall Stud at One End Hole Wall Studs at Both End HolesInstallation for No Wall Studs at End Holes Figures 1 Mark Rear WallDrill Holes in Rear Wall Attach Mounting Plate to Wall Prepare Upper CabinetInstall Damper Assembly Install the Microwave OvenSecure damper assembly with 2 sheet metal screws Check that damper blade moves freely, and opens fullyComplete Installation Connect vent to damper assemblyVenting Design Specifications For optimal venting installation, we recommendRectangular to Round Transition Recommended Standard FittingsReplacement Parts AccessoriesAssistance ¹⁄₄ x 10 8.3 x 25.4 cm vent system = 73 ft 22.2 m totalExigences Dinstallation Outillage et piècesOutillage nécessaire Pièces fourniesExigences demplacement Dimensions du produitPour une installation avec décharge murale seulement Dimensions à respecter lors de linstallationInstructions Dinstallation Spécifications électriquesDépose de la plaque de montage Réorientation du moteur du ventilateurVis dans les trous encastrés Configurations possibles du colombage mural Identifier la position du/des poteaux du colombage muralAucun poteau du colombage à la position des trous ’angle Tracé sur le mur arrière Ôter le gabarit de carton et vérifier les points de tracé35,9 cm de laxe central Perçage de trous dans le mur arrière Fixation de la plaque de montage sur Le murUn trou d’angle face à un poteau du colombage mural Figure Préparation du placard mural L’aide d’une scie à guichet, découper la zone rectangulaireInstallation du module du clapet anti-reflux Installation du four à micro-ondesFixer le clapet anti-reflux à laide de 2 vis de tôlerie Achever linstallation Raccords standard recommandés Spécifications DU Circuit DévacuationRaccord de transition rectangulaire/rond Décharge à travers le murAccessoires Longueur recommandée du circuit dévacuationPièces de rechange Conduit de dia 15,2 cm = longueur totale 73 pi 22,2 m

W10191953A specifications

The Maytag W10191953A is a notable appliance part designed to enhance the performance and efficiency of Maytag washing machines. As a quality component, it reflects Maytag's commitment to robust manufacturing and reliability. This part is primarily recognized as a washing machine door strike, playing an essential role in ensuring the proper sealing and functioning of the washer door.

One of the main features of the W10191953A is its durable construction. Made from high-quality materials, the door strike is designed to withstand the rigors of regular use, ensuring longevity and reducing the likelihood of failure. This robustness is crucial in maintaining the operational integrity of the washing machine, preventing leaks, and ensuring that the door remains securely closed during cycles.

In terms of technology, the W10191953A is engineered for compatibility with a variety of Maytag front-load and top-load washing machines. This versatility makes it an essential replacement part for users looking to maintain their appliance’s optimal performance. The installation of this door strike is straightforward and can often be completed without professional assistance, making it accessible for DIY enthusiasts and homeowners.

The W10191953A also features a precise design that ensures an exact fit, which is essential in maintaining the washer's efficiency. When the door strike is working correctly, it facilitates the activation of safety mechanisms within the washing machine, ensuring that cycles cannot start until the door is correctly secured. This not only enhances user safety but also protects the appliance from potential damage.

Another characteristic of the W10191953A is its ability to reduce operational noise. A properly functioning door strike minimizes the rattling and vibrations that can occur during a wash cycle, leading to a quieter laundry experience. This aspect is particularly valued in households where the washing machine is located near living areas.

In summary, the Maytag W10191953A is an essential component that embodies the quality and reliability of Maytag appliances. With its durable construction, compatibility with various models, ease of installation, safety features, and noise-reducing capabilities, it stands out as a vital part for ensuring optimal washing machine performance. For anyone looking to maintain their Maytag washer, the W10191953A is an excellent choice that promises to deliver lasting benefits.
Top Page Image Contents