Maytag W10191953A installation instructions Install Damper Assembly, Install the Microwave Oven

Page 9

5.Cut the 1¹⁄₂" (3.8 cm) diameter hole at the circular shaded area “G” on the template. This hole is for the power supply cord.

NOTE: If upper cabinet is metal, the supply cord bushing needs to be installed around the supply cord hole, as shown.

B

A

A. Metal cabinet

B. Power supply cord bushing

6.Drill 3/8" (10 mm) holes at points “D” and “E” on the template. These are for two 1/4-20 x 3" bolts and washers used to secure the microwave oven to the upper cabinet.

For Roof Venting Installation Only

7.Cut 3/4" (19 mm) hole at one corner of the shaded rectangular area “F” on Upper Cabinet Template.

8.Using a keyhole saw, cut out the rectangular area.

Install Damper Assembly

(for wall venting only)

1.Check that damper blade moves freely, and opens fully.

2.Position the damper assembly on the back of the microwave oven so that the damper blade hinge is at the top, and the damper blade opens away from the microwave oven.

A B CD

A. Back of microwave oven

B. Damper assembly

C. Damper blade

D. Sheet metal screws

3.Secure damper assembly with 2 sheet metal screws.

Install the Microwave Oven

WARNING

Excessive Weight Hazard

Use two or more people to move and install microwave oven.

Failure to do so can result in back or other injury.

IMPORTANT: The control side of the microwave oven is the heavy side. Handle the microwave oven gently.

1.Place a washer on each 1/4-20 x 3" flat-head bolt and place inside upper cabinet near the 3/8" (10 mm) holes.

2.Make sure the microwave oven door is closed and taped shut.

3.Using 2 or more people, lift microwave oven and hang it on support tabs at the bottom of mounting plate.

NOTE: To avoid damage to the microwave oven, do not grip or use the door or door handle while the microwave oven is being handled.

A

B

A. Mounting plate

B. Support tabs

4.With front of microwave oven still tilted, thread power supply cord through the power supply cord hole in the bottom of the upper cabinet.

5.Rotate microwave oven up toward upper cabinet.

NOTE: If venting through the wall, make sure the damper assembly fits easily into the vent in the wall cutout.

6.Push microwave oven against mounting plate and hold in place.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Microwave Hood Combination Safety Microwave Hood Combination Installation InstructionsTools and Parts Installation RequirementsRemove Cardboard Template Location RequirementsInstallation Dimensions Product Dimensions Electrical RequirementsObserve all governing codes and ordinances RequiredWall Venting Installation Only Installation InstructionsRemove Mounting Plate Rotate Blower MotorSecure damper plate with 2 screws removed in Step Roof Venting Installation OnlyLocate Wall Studs Possible Wall Stud ConfigurationsNo Wall Studs at End Holes Wall Stud at One End Hole Wall Studs at Both End HolesInstallation for No Wall Studs at End Holes Figures 1 Mark Rear WallDrill Holes in Rear Wall Prepare Upper Cabinet Attach Mounting Plate to WallInstall the Microwave Oven Install Damper AssemblySecure damper assembly with 2 sheet metal screws Check that damper blade moves freely, and opens fullyConnect vent to damper assembly Complete InstallationFor optimal venting installation, we recommend Venting Design SpecificationsRectangular to Round Transition Recommended Standard FittingsAccessories Replacement PartsAssistance ¹⁄₄ x 10 8.3 x 25.4 cm vent system = 73 ft 22.2 m totalOutillage et pièces Exigences DinstallationOutillage nécessaire Pièces fourniesDimensions du produit Exigences demplacementPour une installation avec décharge murale seulement Dimensions à respecter lors de linstallationSpécifications électriques Instructions DinstallationDépose de la plaque de montage Réorientation du moteur du ventilateurVis dans les trous encastrés Configurations possibles du colombage mural Identifier la position du/des poteaux du colombage muralAucun poteau du colombage à la position des trous ’angle Tracé sur le mur arrière Ôter le gabarit de carton et vérifier les points de tracé35,9 cm de laxe central Perçage de trous dans le mur arrière Fixation de la plaque de montage sur Le murUn trou d’angle face à un poteau du colombage mural Figure L’aide d’une scie à guichet, découper la zone rectangulaire Préparation du placard muralInstallation du module du clapet anti-reflux Installation du four à micro-ondesFixer le clapet anti-reflux à laide de 2 vis de tôlerie Achever linstallation Spécifications DU Circuit Dévacuation Raccords standard recommandésRaccord de transition rectangulaire/rond Décharge à travers le murLongueur recommandée du circuit dévacuation AccessoiresPièces de rechange Conduit de dia 15,2 cm = longueur totale 73 pi 22,2 m

W10191953A specifications

The Maytag W10191953A is a notable appliance part designed to enhance the performance and efficiency of Maytag washing machines. As a quality component, it reflects Maytag's commitment to robust manufacturing and reliability. This part is primarily recognized as a washing machine door strike, playing an essential role in ensuring the proper sealing and functioning of the washer door.

One of the main features of the W10191953A is its durable construction. Made from high-quality materials, the door strike is designed to withstand the rigors of regular use, ensuring longevity and reducing the likelihood of failure. This robustness is crucial in maintaining the operational integrity of the washing machine, preventing leaks, and ensuring that the door remains securely closed during cycles.

In terms of technology, the W10191953A is engineered for compatibility with a variety of Maytag front-load and top-load washing machines. This versatility makes it an essential replacement part for users looking to maintain their appliance’s optimal performance. The installation of this door strike is straightforward and can often be completed without professional assistance, making it accessible for DIY enthusiasts and homeowners.

The W10191953A also features a precise design that ensures an exact fit, which is essential in maintaining the washer's efficiency. When the door strike is working correctly, it facilitates the activation of safety mechanisms within the washing machine, ensuring that cycles cannot start until the door is correctly secured. This not only enhances user safety but also protects the appliance from potential damage.

Another characteristic of the W10191953A is its ability to reduce operational noise. A properly functioning door strike minimizes the rattling and vibrations that can occur during a wash cycle, leading to a quieter laundry experience. This aspect is particularly valued in households where the washing machine is located near living areas.

In summary, the Maytag W10191953A is an essential component that embodies the quality and reliability of Maytag appliances. With its durable construction, compatibility with various models, ease of installation, safety features, and noise-reducing capabilities, it stands out as a vital part for ensuring optimal washing machine performance. For anyone looking to maintain their Maytag washer, the W10191953A is an excellent choice that promises to deliver lasting benefits.
Top Page Image Contents