Maytag MGC5536 To Convert Appliance For Use With Natural Gas, Reset the Valves for Natural GAS

Page 10

To Convert Appliance For Use With Natural Gas

Electrical power and gas must be turned off prior to conversion.

If this appliance has been converted for use with LP gas, each of the following modifications must be performed to convert the unit back to natural gas.

A. REPLACE ALL ORIFICE SPUDS.

1.Perform Steps 1 and 2 on page 8.

2.Perform Step 3 on page 8.

3.For Step 4: Locate the brass natural gas orifice spuds that were originally installed in this appliance before its conversion for use with LP gas. Observe the number on each of the spuds and note the correct burner location for each spud as shown in figures 14 and 15.

Installation Of Natural Gas Orifice Spuds

5 BURNER MODEL (36￿ WIDE)

FIGURE 14

 

4 BURNER MODEL (30￿ WIDE)

1.10

1.55

1.55

1.85

FIGURE 15

4.Complete Steps 5, 6 and 7 on page 8 to complete the installation of natural gas main spuds in their correct locations.

5.Save the orifices removed from the appliance for future use. They will be needed if this appliance is again converted for use with LP gas.

B.INVERT CAP IN APPLIANCE PRESSURE REGULATOR. (See figure 11).

With the appliance installed the appliance regulator should be located as shown in either figure 3, 4 or 5 (pages 4, 5 & 6). Identify the type of appliance regulator and follow the instructions in the appropriate illustration.

C.RESET THE VALVES FOR NATURAL GAS

1.Light one burner, and set on low.

2.Remove the knob.

3.Remove the rubber grommets.

4.Locate the valve adjustment screw. See figure 12.

5.Insert a slender, thin-blade screwdriver into knob hole and engage blade with slot in adjusting screw.

6.Starting from the LP position (see #5 on page 9, under C. LOW FLAME ADJUSTMENT), turn the screw counter clockwise until the flame stabilizes and matches the pictured “low” setting on figure 13. Proper adjustment will produce a stable, steady blue flame of minimum size. The final adjustment should be checked by turning the knob from high to low several times without extinguishing the flame.

After Steps A, B and C have been completed, check the appearance of each burner’s flame at the Hi and Lo settings against figure 13. If the flames appear too large or too small, make sure all steps were completed correctly.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents 8101P522-60 Cutout Dimensions Are CriticalDimensions InchesLocation Of Your Maytag Appliance Installing Cabinetry Over Your Maytag CooktopRequired Adjustments At Time Of Installation Important Preparation SuggestionsRecreational Park Trailers Installation Of ApplianceMobile Homes Commonwealth Of MassachusettsIf no Other Appliance is to be Installed below this Cooktop Connecting Appliance To Gas SupplyIllustrative GAS Supply Piping Wall Oven Installed below 30 Cooktop Pressure Testing Illustrative Alternative PipingElectrical Wiring Information Electrical Grounding InstructionsRemoval of Orifice Spud Installation Of LP Orifice SpudConverting Appliance For Use With LP Gas Replace ALL Orifice SpudsConversion of Appliance Pressure Regulator LOW Flame Adjustment See figureInvert CAP in Appliance Pressure Regulator See figure To Convert Appliance For Use With Natural Gas Installation Of Natural Gas Orifice SpudsReset the Valves for Natural GAS Invert CAP in Appliance Pressure REGULATOR. See figureBurner Performance MaytagService-Parts Information How To Remove Cooktop For ServicingHolding Unit Down To Countertop Dimensiones PulgadasSugerencias importantes de preparación Ubicación de su electrodoméstico MaytagPreparación de la superficie para cocinar Ajustes necesarios al momento de la instalaciónInstalación del electrodoméstico Casas móvilesRemolques de recreación En la Commonwealth de MassachusettsConexión del electrodoméstico al suministro de gas Ilustración DE LA Tubería DE Suministro DE GASNota, en referencia a la Figura 4, anterior Pruebas de presión Ilustración DE LA Tubería AlternativaInformación de alambrado eléctrico Instrucciones eléctricas de conexión TierraInstalación de la copa de orificio LP Para Quitar LA Copa DE OrificioReemplace Todas LAS Copas DE Orificio Inversión DE LA Tapa DEL Regulador DE Presión Vea la figura Conversión DELRegulador DE Presión Ajuste DE LA Llama Baja Vea la figuraInvierta LA Tapa DEL Regulador DE PRESIÓN. Vea la figura Instalación de las copas de orificio de gas NaturalReajuste LAS Válvulas Para GAS Natural Desempeño de los quemadores Cómo quitar la superficie para cocinar para darle servicio Para sujetar la unidad al mostradorInformación de las piezas de servicio Manuel DE PoucesSuggestions importantes pour la préparation Emplacement de votre appareil ménager MaytagRéglages requis lors de la mise en service Préparation du comptoirPose de l’appareil Maisons mobilesRoulottes de parc Dans le Commonwealth du MassachusettsRaccordement de l’appareil à l’alimentation en gaz Illustration D’UNE Conduite DE GAZFour Mural Monté Sous LA Plaque DE Cuisson DE 30 PO 76,2 CMVérification de la pression Illustration D’UNE Méthode AlternativeCâblage électrique Mise à la terrePose de l’écrou à orifice pour gaz GPL Conversion de l’appareil au gaz GPLDépose DE L’ÉCROU À Orifice Remplacer Tous LES Raccords À OrificeInverser LE Capuchon Dans LE Détendeur Conversion DUDétendeur DE L’APPAREIL Réglage DE LA Flamme À FEU Doux Voir figurePose de raccords à orifice pour gaz naturel Régler LES Boutons DE Commande AU GAZ NaturelPour convertir l’appareil au gaz naturel Inverser LE Capuchon Dans LE Détendeur voir la figureFonctionnement des brûleurs Plaque DE Cuisson Maytag DE 36 PO 91,4 CMFixation de l’appareil au comptoir Informations sur les pièces de rechange

MGC5536 specifications

The Maytag MGC5536 is a high-quality gas cooktop designed to enhance your kitchen cooking experience. Known for its reliability and performance, this model boasts several features and technologies that cater to both amateur cooks and experienced chefs.

At the heart of the MGC5536 is its powerful burner system, featuring five burners that provide various heat options for all types of cooking. The cooktop includes a high-output burner that delivers up to 17,000 BTUs, making it ideal for boiling water quickly or searing meats. The versatility of the burners allows for precise adjustments, ensuring perfect cooking results every time.

One of the standout features of the Maytag MGC5536 is its durable cast iron grates. These grates not only provide a sturdy and stable surface for your pots and pans but also offer a continuous cooking surface. This design makes it easier to move heavy cookware from burner to burner without the hassle of lifting. Additionally, the grates are dishwasher-safe, simplifying the cleaning process after cooking.

The MGC5536 incorporates Maytag's innovative EvenAir technology, which ensures an even distribution of heat across the burners. This technology helps to eliminate hot spots and ensures that food cooks uniformly. Whether you're simmering a sauce or frying vegetables, you can trust that every dish will receive consistent heat for optimal results.

Another notable characteristic of this gas cooktop is its easy-to-use controls. The knobs are ergonomically designed for better grip and precision, allowing users to make exact adjustments while cooking. The cooktop also features a sleek, stainless steel design that complements modern kitchen aesthetics, while also being easy to clean with a simple wipe.

Safety is paramount, and the Maytag MGC5536 is equipped with flame failure safety technology. This feature automatically shuts off the gas supply if the flame goes out, providing peace of mind while cooking.

In summary, the Maytag MGC5536 gas cooktop stands out for its powerful burner system, durable construction, advanced cooking technologies, and user-friendly design. It is an excellent choice for anyone looking to elevate their cooking experience, offering reliability and performance that lasts. With Maytag's commitment to quality, the MGC5536 is designed to handle the demands of everyday cooking while providing exceptional results.
Top Page Image Contents