Bunn TWIN, ITB manual From the NEW AD? screen, select Card, Enable Sanitation, Ergysavr

Page 20

PROGRAMMING THE BREWER (cont.)

PROGRAMMING FUNCTIONS - LEVEL 2 (cont.)

12.Select DONE. The display should now read WRITE BTM LINE?.

13.To write the bottom line, select YES.

14.To skip the bottom line, select NO.

a.If neither a top nor bottom line was written, the display should now read ENABL SANITATION.

b.If only a top line was written, the ad will be displayed followed by SAVE? Proceed to step 18.

15.The display will now read A with a flashing cursor below it. Scroll through the alphabet and available characters. When the desired character is shown on the display, select NEXT to move to the next character in the bottom line.

16.Repeat step 15 until the bottom line is complete.

17.Select DONE. The display will now show the written ad, and then SAVE?

18.To cancel saving the ad, select NO. The display should now read ADVERTISEMENT NOT SAVED! and then will return to the NEW AD screen.

19.To correct or edit the ad, select EDIT. The display should now read WRITE TOP LINE? Repeat steps 10 though 17.

20.To save the ad as it is shown, select YES. The display should now read ADVERTISEMENT SETUP COMPLETE, and then ENABL SANITATION. To exit programming and return to the MAIN SCREEN, press ENABLE BREW ON/OFF switch.

Procedure to READ in a new Ad: Not available on ITB

NOTE: Saving a new ad will erase any previously saved ad in the brewer’s memory.

7.From the NEW AD? screen, select CARD.

8.The display will show INSERT AD CARD. Place the AD CARD vertically so that the top end of the "chip" is beneath the sensing coil (located on the underneath side of the front display panel).

9.After a short pause, the display will read CARD CONTAINS AD. To view the ad, press and release SHOW. To save the ad to the brewer's memory, select SAVE. To cancel, select QUIT.

10.After the ad is saved, the display will read AD MES- SAGE SETUP COMPLETE, and then will advance to

ENABLE SANITATION.

* ENABLE SANITATION

This function allows the operator to enable the sanita- tion function and set the time before a cleaning alert will be displayed.

Procedure for enabling sanitation:

Range: 0.0 to 72.0 hrs

1.Press and hold the right hidden button until the display reads SET LANGUAGE. Press and release the right hidden button until the display reads EN- ABL SANITATION. The YES or NO will be flashing to indicate the current selection.

2.Select NO to disable this function (no sanitation alert will be displayed on the screen), or:

3.Select YES to enable this function (a sanitation alert will displayed on the screen).

4.When finished, select DONE to save the new setting and advance to the next function screen.

5.If NO was selected, the display should now read ENABLE ENERGYSAVR. To exit programming and return to the MAIN SCREEN, press ENABLE BREW ON/OFF switch.

6.If YES was selected, the display should now read X.X HRS -> CLEAN. This screen allows the opera- tor to set the amount of time from when a brew is completed until a sanitize alert will be displayed. Use (-)and (+) to adjust the set time. When finished, select DONE.

NOTE: The timer will not begin until after a brew cycle has been completed.

7.The display should now read X.X HRS UNTIL NEXT CLEAN, and then advance to ENABLE EN-

ERGYSAVR.

8.Once the set time has expired, the display will read PLEASE SANITIZE, and then PRESS FULL FOR 3 SEC TO CANCEL.

9.Clean and sanitize the machine.

10.When finished, press and hold the FULL batch switch to reset the Sanitation timer. The display should now read SANITATION COMPLETE and then will return to the MAIN SCREEN.

Page 20

41581.2 091609

 

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Post Office BOX SPRINGFIELD, Illinois Phone 217 529-6601 FAX 217BUNN-O-MATIC Commercial Product Warranty Itcb ContentsITB ICB Programming the BrewerICB Twin Programming the BrewerITB Programming Functions LevelItcb Itcb ITB Set Recipes TempsUsing a Recipe Card to load recipes Procedure to program the coffee nameProcedure to program the AD SET Language Procedure for setting Brew LockoutProcedure for setting Language Default Recipe Chart ICB Default AssignmentsUnits ICBVIEW/MODIFY Items ICB Sweet MeterITB/ITCB with Factory Sweetener By Pressing SHOW,When finished, press the other batch size and repeat step # Setting Pulse Brew Easy Pulse BrewSetting Pulse Brew/PreInfusion Manual DONE?Procedure Setting Drip TimeSetting Sweet Meter Optional on Itcb Overview only Some Screens Omitted ICB ITB/ITCBProcedure to select switch recipes Procedure to disable a Brew SwitchSelect Done to disable that brew switch No Name Coffee ItcbProcedure for Setting the Recipe SET NEW Recipe Coffee onlySET NEW Coffee Items ICBEnable ADS SET Temp ICB Master Temp ItcbMain Screen Ready DegreeEnable Sanitation Enable SanitationProcedure for enabling sanitation Range 0.0 to 72.0 hrs From the NEW AD? screen, select CardEnable Energy Saver Enable Fresh TimerAble Freshtimer Hot Tea 0.5 to 8.0 hrsProcedure to set the sprayhead flow rate Procedure to adjust the bypass flow rate settingProcedure to adjust the dilution flow rate setting Spray OZ/MProcedure to calibrate the sprayhead flow rate Procedure to calibrate the bypass flow rate ICBProcedure to calibrate the dilution flow rate Itcb Calibrate FlowICB Series Programming Functions Level 2 ITB/ITCB Procedure to view/reset the brew countersBrew Counters SET Recipe Temps Itcb only YESService Number Service ToolsFactory Defaults Asset NumberTroubleshooting Troubleshooting ProblemProbable Cause RemedyProblem Probable Cause Remedy If the left three digit number LongTing Obstructions. Clear or replace Refill valve Automatic refill will not operate or Problem Probable CauseControl Board ON/OFF Switch To it is secure Water flows into tank continuously Refill valveTing Heating Time TOO Long Recipe settings No bypass water Bypass valveLime buildup Been set for the current recipe As requiredBrew volume adjustment Inconsistent beverage levelServer/dispenser 90 psi 138 and 620 kPaTank heaters Remove and clean lime off tank Heaters For proper extractionSolenoids Vibrate during operationWater temperature Weak beverage Type of paper filterCoffee Be used for proper extraction
Related manuals
Manual 36 pages 5.47 Kb

ITB, TWIN specifications

The Bunn TWIN,ITB is a remarkable coffee brewing system designed for commercial use, aimed at establishments that require a high volume of coffee while maintaining superior quality. This innovative brewer stands out through its dual brewing capability, allowing users to brew two different types of coffee simultaneously. This feature is particularly beneficial for cafes, restaurants, and other food service locations where diverse customer preferences must be met efficiently.

One of the main features of the Bunn TWIN,ITB is its advanced brewing technology. The system utilizes Bunn's patented brewing process, ensuring optimal coffee extraction and flavor profile every time. It employs a digitally controlled brew timer and state-of-the-art heating elements, providing precise temperature control essential for achieving the ideal brew. This technology allows for consistent results, ensuring that each cup meets the high standards expected in a commercial setting.

The design of the TWIN,ITB is user-friendly and intuitive. It includes an easy-to-read LED display that simplifies programming and monitoring of the brewing process. This streamlined interface enables baristas to adjust settings quickly and efficiently, significantly reducing wait times for customers. Additionally, the unit's low-profile design enables it to fit seamlessly into various kitchen layouts and countertops, optimizing valuable space.

Durability and reliability are at the forefront of the Bunn TWIN,ITB's construction. Built with high-quality materials, the brewer is designed to withstand the rigors of intense daily use. Its stainless-steel finish not only provides a sleek and professional appearance but also makes it easy to clean and maintain, ensuring longevity and excellent performance throughout its lifespan.

Furthermore, the TWIN,ITB features an impressive water capacity with a built-in hot water tank. This allows users to brew large batches of coffee without interruption and offers instant hot water for tea, soups, or other hot beverages. The efficient brewing system utilizes pre-infusion technology, which saturates the coffee grounds before extraction, enhancing the overall flavor and aroma of the brewed coffee.

In summary, the Bunn TWIN,ITB is an exceptional choice for any commercial establishment looking to provide high-quality coffee efficiently. Its dual brewing capabilities, advanced technologies, user-friendly design, durability, and additional features make it a valuable addition to any coffee service operation. Whether busy mornings or afternoon rushes, this brewer ensures that every cup of coffee meets the high standards of taste and quality that customers expect.
Top Page Image Contents