Bunn JDF-4SB, JDF-4D manual Service, Ballast JDF-2S,4S, Location, Test Procedure

Page 15

SERVICE (CONT.)

Ballast (JDF-2S,4S)

 

JDF-2S shown

FIG. 3 BALLAST

P1684.40

 

Location:

 

The door lamp ballast is located inside the dispenser door mounted in the center of the door rear cover.

Test Procedure:

1.Disconnect the dispenser from the power source.

2.Disconnect a black and blue wire from one set of lamp sockets.

3.Connect an ohmmeter to the end of each wire.

4.Check for continuity between the two wires.

If continuity is present as described, the ballast is operating properly.

If continuity is not present as described, replace the ballast.

5.Check for continuity between the other pair of black and blue wires.

Removal and Replacement:

1.Disconnect the dispenser from the power source.

2.Remove door cover by taking out the 5 screws and unplug the dispense switch harness from the door harness. Set door cover and screws aside.

3.Disconnect the 3-pin connector from the ballasts to the door harness.

4.Remove fluorescent bulbs from the brackets. Pull off the four snap-in light sockets from the light panel.

5.Remove the wire to the ballast from the back of each bracket.

6.To disengage the ballast wire from the bracket, push a 1/16” allen wrench (or equivalent tool) into the front hole that lines up with the wire in the back. Pull the wire out.

7.Repeat for each bracket.

8.White jumper must remain in place on the back of the light socket.

9.Remove screws from each ballast. Remove the green ground wire from the ballast bracket by removing the bracket’s bottom screw.

10.Install the single ballast (wires on the bottom) onto the ballast bracket using 2 of the screws previously removed.

11.Attach ballast wires to the back of bulb sockets by pushing wires into holes in back of socket.

Note: Attach black wires to the top sockets, and blue wires to the bottom sockets. Reference electrical sche- matic if needed.

12.Snap all 4 bulb sockets back onto light panel. Re- install fluorescent bulbs.

13.Attach green ground wire to the bottom hole of the ballast bracket using 1 screw.

14.Plug in 3-pin connector into the door harness.

15.To replace door cover, re-connect the dispense switch harness to door harness. Fasten with 5 screws.

16.Reconnect power to the unit. Test operation.

P1219

FIG. 4 BALLAST TERMINALS

15

49179

110613

 

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Phone 217 529-6601 FAX 217 JDF-4D, JDF-4SBBUNN-O-MATIC Commercial Product Warranty Introduction Recommended Daily Cleaning Instructions Required Regular Maintenance Problem Probable Cause Cold Water CirculationRemedy Problem Probable Cause Remedy RefrigerationDispenser Locked Out Check for kinked flex line When dispensing. If yes, replaceContinuity Ed replace relayWater only Concentrate only100psi Nect fittingsTray Water pressure greater thanReplace control board Pump tubing Inspect, clean, or replace tubing AgeAdapter assembly Unit is not workingComponent Access ServiceAccess Panels Servicecont Access PanelsDispense Platform Removal Servicecont Dispense Platform RemovalLocation ServiceTest Procedure Ballast JDF-2S,4SCabinet Fan all Models Remove the four screws attaching the fan and cover assemblyLocation LG Compressor JDF-2S,4S,4DDesign Pressures High 335 Low 88 psi CompressorCompressor GD Compressor JDF-2S,4S,4DDisconnect and remove the transformer Compressor Thermal Compressor JDF-4SBBLU/BLK Compressor Switch Compressor Switch all ModelsCondenser FAN Condenser Fan all ModelsControl Board, Main all Models Test Procedure Power Supply CircuitryTo the transformer See Transformer Portion Control Board JDF-2S,4SWith a voltmeter, back probe check the voltage Source. The indication must be 24 volts acPush Button Control Board Push Button Control Board JDF-4DPortion Control Board JDF-4D With a voltmeter Circulation Pump all ModelsDispense Platform Switch all Models Disconnect the two black wires from the switchReturn power to the dispenser Dispense Pump Dispense Pump all Models except JDF-4DDispense Motor all Models Reconnect the two wires to the motor as shown in FigDispense Valve Dispense Valve all ModelsDispense Switches Dispense Switches JDF-2S, JDF-4SCold Water Dispense Switch Cold Water Dispense Switch JDF-4S onlyLocation Dispense Membrane Switch all ModelsMembrane Switch EMI Filter EMI Filter all ModelsLamps & Holders Lamps, Holders and Ballasts Early ModelsDisconnect power from the dispenser LED Lamps JDF-2S, JDF-4SLED regulator board Rectifier Rectifier JDF-2S, JDF-4SRefer to to reconnect the wires Relay all ModelsVolts ac for 120 volt models Volts ac for 230 volt models Resistor Resistor all 230V ModelsIf voltage is present as described, proceed to #5 Solenoid Cold Water JDF-4S only120V 1.2 kΩ 230V 3.84 kΩ Solenoid Inlet all Models77 F 8k 10.2k Ω Temperature Probe all ModelsTemp Resistance Voltage 32 F 31.2k 34k ΩTemperature Sensor all Models 32 F 5k Ω77 F 350 Ω Transformer Terminals Transformer all ModelsTransformer Lited Doors JDF-2S, JDF-4S Water Q7 Compressor Relay Q25Water Q27 Water Q28Diagram for JDF-2S LED Lited Doors Schematic Wiring Schematic Wiring Diagram JDF-4S Schematic Wiring Diagram JDF Schematic Wiring Diagram JDF-4D Schematic Wiring Diagram JDF-4D Electrical Schematic Diagram
Related manuals
Manual 28 pages 48.61 Kb Manual 28 pages 35.87 Kb Manual 31 pages 40.19 Kb

JDF-4D, JDF-4SB, JDF-4S specifications

The Bunn JDF-4S is a high-performance commercial coffee brewer designed to meet the needs of busy coffee shops, restaurants, and other establishments requiring a reliable and efficient coffee brewing solution. This versatile machine boasts an array of advanced features and technologies, making it a prominent choice among professionals in the coffee industry.

One of the most notable features of the Bunn JDF-4S is its ability to brew up to 4 gallons of coffee per hour, ensuring that establishments can keep pace with high-demand environments. This capacity makes it an ideal choice for venues that experience peak periods of coffee consumption, minimizing wait times for customers. The machine is designed with a multiple-brew option, allowing users to select various brew methods, which can cater to diverse customer preferences.

The JDF-4S incorporates Bunn’s patented brewing technology, which utilizes a precision-controlled process to ensure optimal flavor extraction. The brewed coffee is delivered at an ideal temperature, typically between 195°F and 205°F, promoting maximum taste and aroma. The machine also features a programmable digital controller that enables users to set specific brew times and adjust water temperature settings to achieve consistent results.

Another significant characteristic of the Bunn JDF-4S is its durability and ease of use. Constructed with high-quality materials, the machine is built to withstand the rigors of daily operation. The user-friendly interface features a simple touchpad design for easy navigation and programming. Additionally, the machine includes a built-in diagnostics program, helping users quickly identify and troubleshoot potential issues, thereby minimizing downtime.

The JDF-4S also offers flexible brewing options, including iced coffee brewing, enhancing its versatility. It is compatible with Bunn’s extensive range of coffee and tea dispensers, allowing businesses to expand their beverage offerings effortlessly. Furthermore, the unit features an easy-access water reservoir for quick refilling and reduced wait times during busy service periods.

In terms of maintenance, the Bunn JDF-4S is designed with user convenience in mind. The machine includes a rinse and clean cycle to ensure optimal hygiene and coffee quality. Integrated clean alerts guide users through the cleaning process, promoting regular upkeep and ensuring the longevity of the brewer.

In summary, the Bunn JDF-4S represents a cutting-edge solution for coffee brewing that prioritizes performance, versatility, and ease of use. With its advanced brewing technology, user-friendly features, and robust construction, it offers an exceptional choice for businesses seeking to serve high-quality coffee efficiently.
Top Page Image Contents