Bunn JDF-4SB, JDF-4D manual Blu/Blk

Page 22

SERVICE (CONT.)

Compressor (Cont.)

Removal and Replacement:

Compressor Start Relay: Refer to FIG. 16

1.Remove the terminal cover (4)

2.Disconnect the wires from the compressor start relay.

3.Pull relay (1) off of the compressor pins and dis- card.

4.Push new relay onto the compressor pins.

5.Refer to Fig. 16 and reconnect the wires.

6.Reinstall terminal cover (4).

Compressor Thermal Overload Protector: Refer to FIG. 16

1.Remove terminal cover (4).

2.Disconnect the WHI/ORN wire of the harness from the thermal overload protector.

3.Disconnect the BLK wire from the Compressor’s upper terminal.

4.Remove overload protector (3) and start relay as an assembly.

5.Remove overload protector (3) and discard overload protector.

6.Install new overload protector (3) on to the relay

(1).

7.Install relay (1) and overload protector (2) on the compressor terminal bracket.

8.Refer to Fig. 17 and reconnect the thermal overload protector wires.

9.Reinstall terminal cover (4).

Compressor Assy:

NOTE: Before removal of any refrigeration component the refrigerant in the system must be reclaimed by a licensed refrigeration repair person.

NOTE: When replacing the compressor it is recom- mended that the dryer also be replaced.

1.Disconnect the tubes from the condenser and the accumulator.

2.Disconnect the compressor wiring harness from the dispenser main wiring harness.

3.Remove the four .25-20 keps nuts and washers securing the compressor to the chassis. Set nuts and washers aside for reassembly.

BLU/BLK

GRN

WHI

BLU from Capacitor

BRN from Capacitor

FIG. 17 RELAY TERMINALS

Plugs into Relay

FIG. 18 THERMAL OVERLOAD PROTECTOR

TERMINALS

4.Disconnect and remove the transformer.

5.From the right side of the dispenser lift the com- pressor assembly over the four studs in the chassis and remove compressor.

6.Install new compressor over the four studs in the dispenser chassis with the fill valve to the right side of the dispenser.

7.Secure compressor to the dispenser chassis using four .25-20 keps nuts and washers.

8.Reconnect tubes from the condenser and the ac- cumulator to the compressor.

9.Reinstall transformer.

10.Evacuate the system.

11.Recharge 120V and 230V system with:

JDF-4SB - 10 oz. Type R134A refrigerant. Design Pressures: High 335 - Low 88 psi

NOTE: The charging of the system must be done by a licensed refrigeration repair person.

NOTE: Refer to Wiring Diagrams when reconnecting wires to Compressor, Thermal Overload Protector and Start Relay.

22

49179

110613

 

Page 21 Page 23
Image 22
Page 21 Page 23
Contents JDF-4D, JDF-4SB Phone 217 529-6601 FAX 217BUNN-O-MATIC Commercial Product Warranty Introduction Recommended Daily Cleaning Instructions Required Regular Maintenance Cold Water Circulation Problem Probable CauseRemedy Refrigeration Problem Probable Cause RemedyDispenser Locked Out Ed replace relay When dispensing. If yes, replaceContinuity Check for kinked flex lineConcentrate only Water onlyWater pressure greater than Nect fittingsTray 100psiUnit is not working Pump tubing Inspect, clean, or replace tubing AgeAdapter assembly Replace control boardService Component AccessServicecont Access Panels Access PanelsServicecont Dispense Platform Removal Dispense Platform RemovalBallast JDF-2S,4S ServiceTest Procedure LocationRemove the four screws attaching the fan and cover assembly Cabinet Fan all ModelsLG Compressor JDF-2S,4S,4D LocationCompressor Design Pressures High 335 Low 88 psiGD Compressor JDF-2S,4S,4D CompressorDisconnect and remove the transformer Compressor JDF-4SB Compressor ThermalBLU/BLK Compressor Switch all Models Compressor SwitchCondenser Fan all Models Condenser FANTest Procedure Power Supply Circuitry Control Board, Main all ModelsSource. The indication must be 24 volts ac Portion Control Board JDF-2S,4SWith a voltmeter, back probe check the voltage To the transformer See TransformerPush Button Control Board JDF-4D Push Button Control BoardPortion Control Board JDF-4D Circulation Pump all Models With a voltmeterDisconnect the two black wires from the switch Dispense Platform Switch all ModelsReturn power to the dispenser Dispense Pump all Models except JDF-4D Dispense PumpReconnect the two wires to the motor as shown in Fig Dispense Motor all ModelsDispense Valve all Models Dispense ValveDispense Switches JDF-2S, JDF-4S Dispense SwitchesCold Water Dispense Switch JDF-4S only Cold Water Dispense SwitchDispense Membrane Switch all Models LocationMembrane Switch EMI Filter all Models EMI FilterLamps, Holders and Ballasts Early Models Lamps & HoldersLED Lamps JDF-2S, JDF-4S Disconnect power from the dispenserLED regulator board Rectifier JDF-2S, JDF-4S RectifierRelay all Models Refer to to reconnect the wiresVolts ac for 120 volt models Volts ac for 230 volt models Resistor all 230V Models ResistorSolenoid Cold Water JDF-4S only If voltage is present as described, proceed to #5Solenoid Inlet all Models 120V 1.2 kΩ 230V 3.84 kΩ32 F 31.2k 34k Ω Temperature Probe all ModelsTemp Resistance Voltage 77 F 8k 10.2k Ω32 F 5k Ω Temperature Sensor all Models77 F 350 Ω Transformer all Models Transformer TerminalsTransformer Lited Doors JDF-2S, JDF-4S Water Q28 Compressor Relay Q25Water Q27 Water Q7Diagram for JDF-2S LED Lited Doors Schematic Wiring Schematic Wiring Diagram JDF-4S Schematic Wiring Diagram JDF Schematic Wiring Diagram JDF-4D Schematic Wiring Diagram JDF-4D Electrical Schematic Diagram
Related manuals
Manual 28 pages 48.61 Kb Manual 28 pages 35.87 Kb Manual 31 pages 40.19 Kb

JDF-4D, JDF-4SB, JDF-4S specifications

The Bunn JDF-4S is a high-performance commercial coffee brewer designed to meet the needs of busy coffee shops, restaurants, and other establishments requiring a reliable and efficient coffee brewing solution. This versatile machine boasts an array of advanced features and technologies, making it a prominent choice among professionals in the coffee industry.

One of the most notable features of the Bunn JDF-4S is its ability to brew up to 4 gallons of coffee per hour, ensuring that establishments can keep pace with high-demand environments. This capacity makes it an ideal choice for venues that experience peak periods of coffee consumption, minimizing wait times for customers. The machine is designed with a multiple-brew option, allowing users to select various brew methods, which can cater to diverse customer preferences.

The JDF-4S incorporates Bunn’s patented brewing technology, which utilizes a precision-controlled process to ensure optimal flavor extraction. The brewed coffee is delivered at an ideal temperature, typically between 195°F and 205°F, promoting maximum taste and aroma. The machine also features a programmable digital controller that enables users to set specific brew times and adjust water temperature settings to achieve consistent results.

Another significant characteristic of the Bunn JDF-4S is its durability and ease of use. Constructed with high-quality materials, the machine is built to withstand the rigors of daily operation. The user-friendly interface features a simple touchpad design for easy navigation and programming. Additionally, the machine includes a built-in diagnostics program, helping users quickly identify and troubleshoot potential issues, thereby minimizing downtime.

The JDF-4S also offers flexible brewing options, including iced coffee brewing, enhancing its versatility. It is compatible with Bunn’s extensive range of coffee and tea dispensers, allowing businesses to expand their beverage offerings effortlessly. Furthermore, the unit features an easy-access water reservoir for quick refilling and reduced wait times during busy service periods.

In terms of maintenance, the Bunn JDF-4S is designed with user convenience in mind. The machine includes a rinse and clean cycle to ensure optimal hygiene and coffee quality. Integrated clean alerts guide users through the cleaning process, promoting regular upkeep and ensuring the longevity of the brewer.

In summary, the Bunn JDF-4S represents a cutting-edge solution for coffee brewing that prioritizes performance, versatility, and ease of use. With its advanced brewing technology, user-friendly features, and robust construction, it offers an exceptional choice for businesses seeking to serve high-quality coffee efficiently.
Top Page Image Contents