Bunn T3A, T6A Service Digital Brew Timer Late Models, If voltage is as described, proceed to #7

Page 18

SERVICE (cont.)

DIGITAL BREW TIMER (Late Models)

P2207.50

FIG. 6 DIGITAL BREW TIMER

Location:

The timer is located inside the hood, attached to the left side.

Test Procedure.

NOTE: Do not remove or install wires while timer board is installed. Pressure applied to one side may cause damage to the board.

1.Disconnect the brewer from the power source and remove the front access panel.

2.Remove the two #8-32 screws securing circuit board to the mounting bracket.

3.Remove circuit board and spacers (as required).

4.With a voltmeter, check the voltage across termi- nals TL1 and TL2 when the "ON/OFF" switch is in the "ON" position. Connect the brewer to the power source. The indication must be:

a)120 volts ac for two wire 120 volt models.

b)240 volts ac for two wire 240 volt models.

c)100 volts ac for two wire 100 volt models.

5.Disconnect the brewer from the power source.

If voltage is present as described, proceed to #6.

If voltage is not present as described, refer to the Wiring Diagrams and check the brewer wiring har- ness.

6.With a voltmeter, check the voltage across termi- nals TL1 and TL4 when the "ON/OFF" switch is in the "ON" position. Connect the brewer to the power source. The indication must be 0 volts.

If voltage is as described, proceed to #7.

If voltage is not as described, disconnect the brewer from the power source and replace the timer.

7.With a voltmeter, check the voltage across termi- nals TL1 and TL4 when the "ON/OFF" switch is in the "ON" position. Connect the brewer to the power source and press the "START" switch. The indica- tion must be as follows:

a)120 volts ac for two wire 120 volt models.

b)240 volts ac on two wire 240 volt models.

c)100 volts ac for two wire 100 volt models.

If voltage is present as described, the brew timer is operating properly. Reset the timer as required, to obtain the desired brew volume.

If voltage is not present as described, disconnect the brewer from the power source and replace the timer.

Removal and Replacement:

1.Remove the two #8-32 screws securing circuit board to the mounting bracket.

2.Remove circuit board and spacers (as required).

3.Remove all wires from the timer.

4.Attach all wires to the replacement timer board prior to installation to the component mounting bracket. Refer to FIG. 7 when reconnecting the wires.

5.Install new circuit board with spacers (as re- quired) to the component mounting bracket.

6.Adjust the timer as described below.

Timer Setting:

NOTE: Prior to setting or modifying volumes, check that the brewer is connected to water supply, the tank is properly filled, and a funnel and server are in place. NOTE: All volume settings must be done with the sprayhead installed.

Page 18

10145

072600

 

 

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Post Office BOX SPRINGFIELD, Illinois Telephone 217 529-6601 FAX 217Warranty IntroductionUser Notices #00831.0000 #00656.0000 #03408.0000 #03409.0000Electrical Requirements Plumbing RequirementsElectrical Hook-Up Initial Timer Adjustment Initial SET-UP Fill & HeatAdjusting Brew Volumes ON/OFF Switch T3 onlyOperating Controls Start Switch CleaningSelector Switch T6 only TEA BrewingTroubleshooting Problem Probable Cause Brew cycle will not startRemedy Troubleshooting ProblemProbable Cause Remedy Problem Probable Cause Remedy Dilution cycle will not start Dilution Solenoid ValveSpitting or excessive steaming Control Thermostat Drip-out time too longDripping from sprayhead Beverage overflows dispenser Weak beverage Dry tea leaves remain in the funnel Brewer is making unusal noisesPlumbing Lines Water Supply Tank Heater Service Component AccessContents Service Brew Solenoid ValveService Brew Solenoid Valve Solenoid Valve TerminalsIf voltage is present as described, proceed to #4 Brew TimerIndication must be If continuity is not present as described, refer toService Digital Brew Timer Late Models If voltage is as described, proceed to #7Service Digital Brew Timer Late Modelscont Digital Timer WiringControl Thermostat Test Procedure Disconnect the brewer from the power source Dilution Solenoid ValvesDilution Timer ClockwiseSource. The indication must be Limit Thermostat With a voltmeter, check the voltage acrossON/OFF or Selector Switch On left or right position WHI/VIOStart Switch Tank Heater 10145 072600 10145 072600 10145 072600
Related manuals
Manual 30 pages 4.71 Kb

T6, T6A, T3A specifications

The Bunn T6A, T3A, T6, and T3 are part of a distinguished line of commercial coffee brewers engineered for consistency, efficiency, and top-notch brew quality. These machines are well-suited for cafes, restaurants, and specialty coffee shops where reliability and performance are paramount.

The Bunn T6A is designed to brew large quantities, accommodating high-demand environments. With a capacity of six gallons per hour, this machine can quickly fulfill orders, ensuring that customers receive fresh, hot coffee without delay. It features a programmable touchpad that allows users to customize brew settings, enabling them to fine-tune extraction times and temperatures for various coffee blends. The T6A’s dual-float system provides precise water control, preventing overflow and enhancing safety.

The Bunn T3A is another exceptional model in this lineup, designed for both versatility and speed. It boasts a three-gallon capacity, making it ideal for medium-sized establishments. The T3A is equipped with Bunn's patented SplashGard funnel, which helps protect users from hot water splashes, providing an additional layer of safety. Its advanced brewing technology allows for an optimal brew temperature range, ensuring that coffee is extracted to perfection every time.

The Bunn T6 is similar to the T6A in its heavy-duty construction but focuses on a slightly different brewing capacity. Capable of producing back-to-back brews, the T6 can keep up with high-volume demands. This model features a digital brewer interface, making it user-friendly while providing detailed feedback on the brewing process. Its robust design allows for easy maintenance, ensuring it remains in peak operating condition.

Lastly, the Bunn T3 serves as a compact alternative in the series, suited for locations with limited space but requiring high-quality coffee. The T3 can brew up to three gallons per hour, seamlessly fitting into smaller setups without compromising on performance. Like its counterparts, it features programmable settings and quick brew times, providing flexibility and efficiency.

Together, the Bunn T6A, T3A, T6, and T3 represent a versatile range of commercial coffee brewing solutions. Each model is designed to deliver exceptional coffee, maintain consistent quality, and provide ease of use, making them integral tools for any serious coffee business. Whether high volume or limited space, Bunn caters to diverse needs while upholding the highest standards in coffee brewing technology.
Top Page Image Contents