Bunn JDF-2N manual Troubleshooting, Problem Probable Cause, All water LEDs flash

Page 21

TROUBLESHOOTING

A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic Technical Service Department.

Inspection, testing, and repair of electrical equipment should be performed only by qualified service person- nel.

All electronic components have 120-240 volt ac and low voltage dc potential on their terminals. Shorting of terminals or the application of external voltages may result in board failure.

Intermittent operation of electronic circuit boards is unlikely. Board failure will normally be permanent. If an intermittent condition is encountered, the cause will likely be a switch contact or a loose connection at a terminal or crimp.

Solenoid removal requires interrupting the water supply to the valve. Damage may result if solenoids are energized for more than ten minutes without a supply of water.

The use of two wrenches is recommended whenever plumbing fittings are tightened or loosened. This will help to avoid twists and kinks in the tubing.

Make certain that all plumbing connections are sealed and electrical connections tight and isolated.

This brewer is heated at all times. Keep away from combustibles.

WARNING – • Exercise extreme caution when servicing electrical equipment.

Unplug the brewer when servicing, except when electrical tests are specified.

Follow recommended service procedures.

Replace all protective shields or safety notices.

PROBLEM

PROBABLE CAUSE

REMEDY

All water LED's flash.

1. Bath water level low.

Access bath fill valve and top off bath tank.

Cold Water Circulation

All dispense stations not working or all water & refill LED's flash and beep 3 times.

Note: Cooling failure or excessive bath and cabinet temperatures for m ore than 4 hours will result in touchpad lockout or no dispense. Note: Reset faul/timer by unplug- ging unit.

1.Cabinet cooling fan.

2.Bath recirculation pump.

3.Restricted water flow to cabinet water coil and bath.

Replace fan (24vdc).

Note: Fan receives power when door switch is closed.

A)If not running, replace pump (120vac).

B)If no power, replace control board.

Clean or replace cabinet water strainer or recirculating manifold or check for kinked hose.

21

38310 010406

 

Image 21
Contents Phone 217 529-6601 FAX 217 Post Office BOX SPRINGFIELD, IllinoisContents User Notices Electrical Requirements Initial SET-UPPlumbing Requirements Electrical HOOK-UPInitial Fill Connection Initial FillPriming LoadingPlumbing Hookup Frozen ConcentratesRefrigeration Switch Refrigeration SwitchSanitize Switch Operating ControlsOperating Controls Dispenser USE Press and Hold Models Refer to FigPortion Control Models Refer to Fig Cleaning & Preventive Maintenance Daily Parts WashingWeekly Sanitizing Cleaning Annually Replace Pump Tubing Cleaning Monthly Clean Condenser Air FilterTemperature Compensated Refractometer Method Adjustment & Optional SettingsMix Ratio Product Brix %Per 3-second test Cup Size Programming Portion Control Dispensers Only Adjustment & Optional Settings Pump Speed ProgrammingService Lockout Adjustment & Optional Settings Dispenser LockoutPassword Protection Adjustment & Optional SettingsBeeper Fault Dispense Fault ListCooling Fault List DBC display FaultRefill indicator when concentrate out is detected Dip Switch Function ListControls Off Audio feedback during dispensesFunction List Problem Probable Cause TroubleshootingAccess bath fill valve and top off bath tank All water LEDs flashProblem TroubleshootingCooling system failure or DBC fault RemedyDispense touchpad Bottle adapter switch mem- braneRefill LED not extinguishing All stations dispense concentrate Main water supply OnlyProblem Probable Cause Remedy Concentrate onlyWater only Cant access programming Programming password feature Initial fill/setupPassword Nect fittingsIs powered from the step-down Fault codesOnce water is set, adjust motor Step-down transformerStation Difficulty brixing and/or weak bev Pump tubing ErageUse of portable water pump Difficulty brixing bag-in-boxCoolant Schematic Diagram Schematic Wiring Diagram Schematic Wiring Diagram Schematic Wiring Diagram JDF-2 Control Panel Circuit Schematic Wiring Diagram JDF-2 Remaining Circuits

JDF-2N specifications

The Bunn JDF-2N is a high-performance coffee brewing system that has gained popularity among coffee enthusiasts and professionals for its innovative features and exceptional brewing capabilities. Designed with user convenience and operational efficiency in mind, this machine is ideal for cafes, restaurants, and various other commercial settings.

One of the standout features of the Bunn JDF-2N is its dual brewing capability. It allows for simultaneous brewing of two distinct coffee batches, accommodating high demand and ensuring that customers receive fresh coffee promptly. This feature is particularly advantageous in busy environments, where quick service is essential to maintain customer satisfaction.

The brewing technology employed in the JDF-2N is designed to optimize extraction and flavor. The machine utilizes a precisely controlled spray head that saturates coffee grounds evenly, allowing for a consistent extraction process. This results in a rich, flavorful coffee that highlights the unique characteristics of each coffee blend. Additionally, the machine is equipped with a large-capacity water reservoir, which guarantees a steady flow of hot water, further enhancing brewing efficiency.

Another notable characteristic of the Bunn JDF-2N is its intuitive digital control panel. This user-friendly interface allows baristas and operators to easily adjust brewing parameters, such as brew temperature and time, tailoring the process to specific coffee types or personal preferences. The programmable features enable users to save their favorite settings, ensuring a consistent coffee experience with every brew.

The build quality of the Bunn JDF-2N is robust, featuring durable stainless steel construction that not only maintains aesthetic appeal but also ensures longevity. The machine is designed with serviceability in mind, allowing for easy access to components for maintenance and repairs.

Moreover, the Bunn JDF-2N is equipped with an innovative hot water faucet, offering immediate access to hot water for tea, soup, or other hot beverages, further enhancing its versatility in a commercial setting.

In summary, the Bunn JDF-2N stands out with its dual brewing functionality, advanced extraction technology, user-friendly interface, and durable construction. It represents an ideal solution for businesses that prioritize quality, efficiency, and customer satisfaction in their coffee offerings. With its array of features and reliable performance, the Bunn JDF-2N is a noteworthy choice for any establishment looking to elevate its coffee service.