Haier WQP12-CFESS manual Installation Diagram

Installation

Positioning the Appliance

Positioning the appliance in the desired location. The back should rest against the wall behind it, and the sides, along the adjacent cabinets or wall. The dishwasher is equipped with water supply and drain hoses that can be positioned to the right or the left of the appliance.

Levelling the Appliance

Once the appliance is positioned, adjust the feet (screwing them in or out) to adjust the level of the dishwasher. The appliance should not be inclined more than 2˚. If it is level, it will help en- sure proper performance.

Cold Water Connection

Connect the cold water supply hose to a threaded 3/4 (gas) connector, making sure that it is fastened tightly in place (see fig. 1).

If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet filter may get blocked and damage the appliance.

Hot Water Connection

The water supply to the appliance can also be connected to the house's hot water line (centralised system, heating system), as long as it does not exceed a temperature of 60.

Drain Hose Connection

Insert the drain hose into a drain pipe with a minimum diameter of 4cm, Or let it run into the sink, making sure to avoid bending or crimping it. Use the special plastic support that comes with the appliance (see fig.2). The free end of the hose must be at a height between 40 and 100 cm and must not be immersed in water.

MAX 100	MIN 40
	fig.2

Installation

Diagram

In this case,the wash cycle time will be shortened by about 15 minutes and the wash efficiency slightly reduced.

The connection must be made to the hot water line following the same procedures as those for the connection to the cold water

Attention:

The special plastic hose support must be solidly fastened to the wall to prevent the drain hose from moving and allowing water to spill outside the drain.

A

		B
	3(1)	1(2)
	N
	IG	LS C
	L
	4(2)	2(1)
~	F
220-240V

IS

D

E

1

1

2 3

line.

fig.1

Electrical Connection

After making sure that the voltage and frequency values for the current in the home correspond to those on the rating plate (located on the stainless steel inner door of the appliance) and that the electrical system is correct for the maximum voltage on the rating plate, insert the plug into an electrical socket which is earthed properly (the earthing of the appliance is a safety re- quirement mandated by law).

If the electrical socket to which the appliance must be connected is not appropriate for the plug, replace the plug, rather than us- ing adaptors or the like as they could cause overheating and

P

O

CnP3

1

2

3

4

5

6

7

8

CnP1

6

5

4

3

2

1

CnL1

control panel

1 2 3 4 5 6 7 8

CnP2

12

11

10

9

8

7

6

5

4

3

2

1

N

F

						K
	G	H	1	I		4
Q	D-ED	1/2		IAQS		ML
				2	1
			3			2
						C

J 1

L

M

L

burns.

Caution:

The dishwasher plug must be accessible even when the appli- ance is installed as a built-in unit so that maintenance can be done safety.

RELE'

A. Wiring box	B.Power switch	C.Power indicator		D.Door switch	E.Water leve
F.Drain pump	G.Dispenser	H.1/2 washing valve		I.Overflow switch	J.Inlet valve
K.Washing pump	L.Temperature limiter		M.Heater	N.Relay	O.Sensor tempe
P.Rinsing agent missing switch		Q. Fan

.9. .10.