Hoshizaki KM-1300SAH3, KM-1300SWH3, KM-1300SRH3 service manual Maintenance

Page 69

3. Maintenance

IMPORTANT

This icemaker must be maintained individually, referring to the instruction manual and labels provided with the icemaker.

1) Stainless Steel Exterior

To prevent corrosion, wipe the exterior occasionally with a clean and soft cloth. Use a damp cloth containing a neutral cleaner to wipe off oil or dirt build up.

2)Storage Bin and Scoop

•Wash your hands before removing ice. Use the plastic scoop provided.

•The storage bin is for ice use only. Do not store anything else in the bin.

•Keep the scoop clean. Clean it by using a neutral cleaner and rinse thoroughly.

•Clean the bin liner by using a neutral cleaner. Rinse thoroughly after cleaning.

3)Condenser (Except water-cooled model)

Check the condenser once a year, and clean if required by using a brush or vacuum cleaner. More frequent cleaning may be required depending on the location of the icemaker.

4) Air Filters

Plastic mesh air filters remove dirt or dust from the air and keep the condenser from getting clogged. As the filters get clogged, the icemaker’s performance will be reduced. Check the filters at least twice a month. When clogged, use warm water and a neutral cleaner to wash the filters.

69

Page 68 Page 69
Image 69
Page 68 Page 69
Contents Hoshizaki Stackable Crescent Cuber Hoshizaki AMERICA, INC Contents Page KM-1300SAH Specifications IcemakerWater Cooled Condenser KM-1300SWHKM-1300SRH KM-1300SAH3 KM-1300SWH3 KM-1300SRH3 URC-12F Condensing UnitSpecifications Model URC-12F KM-1300SAH, KM-1300SAH3 II. General Information ConstructionKM-1300SWH, KM-1300SWH3 KM-1300SRH, KM-1300SRH3 Controller Board Features of Control Products E Controller BoardSolid-State Control Controller BoardPage Minute Fill Cycle Beep every 3 sec. = High Evaporator Temperature 127 FHarvest Cycle CycleControl Products HOS-001A Board Sequence 1st Cycle Important Water Valve opening is limited to 6 minutes 2nd Cycle and after with pump drain2nd Cycle and after with no pump drain Dip switch is factory-adjusted to the following positions Controls and AdjustmentsSetting Time Setting Frequency Checking the Controller Board Page KM-1300SAH, KM-1300SAH3 KM-1300SWH, KM-1300SWH3 KM-1300SRH, KM-1300SRH3 KM-1300SAH, KM-1300SWH Wiring DiagramsPsig KM-1300SAH3, KM-1300SWH3 Cut-out 412 0 +21.3 Psig Cut-in 327 ± 21.3 Psig Timing Chart Page 327 Performance Data1284 1296 1320 1254 1308 Problem Possible Cause Remedy IV. Service Diagnosis No Ice ProductionProblem Possible Cause Remedy Water Regulator Water Problem Possible Cause Remedy Evaporator is Frozen Up Low Ice Production Abnormal IceOther Service for Refrigerant Lines Removal and Replacement of ComponentsRefrigerant Recovery Evacuation and Recharge R-404ABrazing Removal and Replacement of Compressor Removal and Replacement of Drier Removal and Replacement of Expansion Valve Removal and Replacement of Hot Gas Valve and Line Valve Removal and Replacement of Evaporator Page Adjustment of Water Regulating Valve Water-Cooled Model Only Page Removal and Replacement of Thermistor Removal and Replacement of Fan Motor Removal and Replacement of Pump Motor Removal and Replacement of Water ValveRemoval and Replacement of Spray Tubes Preparing the Icemaker for Long Storage VI. Maintenance and Cleaning InstructionsPage Cleaning and Sanitizing Procedures Cleaning Procedure Page Sanitizing Procedure Following Cleaning Procedure Maintenance

KM-1300SRH3, KM-1300SWH, KM-1300SRH, KM-1300SAH, KM-1300SWH3 specifications

The Hoshizaki KM-1300 series ice makers are designed to meet the demands of high-volume establishments requiring consistent, high-quality ice production. Among the models in this series are the KM-1300SAH3, KM-1300SWH, KM-1300SRH3, KM-1300SWH3, and KM-1300SAH, each boasting a variety of features and technologies to enhance efficiency and reliability.

One of the standout features of the KM-1300 series is its impressive ice production capacity. Each model is capable of producing up to 1,300 pounds of ice in a 24-hour period, making them ideal for busy restaurants, hotels, or bars that serve a high volume of customers. The machines are designed to create crescent ice, known for its pellet-like texture that is perfect for drink service and food display.

Energy efficiency is another key characteristic of the Hoshizaki KM-1300 models. They are equipped with a highly efficient refrigeration system that minimizes energy consumption while maximizing output. Many of the models in this series are certified by Energy Star, helping operators reduce their environmental footprint and lower operational costs.

Durability and ease of maintenance are also prominent features of the KM-1300 series. Constructed with stainless steel exteriors, these ice makers are built to withstand the rigors of a busy kitchen environment. Additionally, Hoshizaki has incorporated a unique air-cooled condenser design, which reduces the need for frequent servicing and minimizes downtime.

The KM-1300SAH3 and KM-1300SAH models come with advanced touch controls and a user-friendly interface, allowing operators to monitor and adjust settings with ease. The built-in self-diagnostic system alerts users to potential issues before they escalate, improving reliability and ensuring consistent ice production.

For those seeking flexibility, the KM-1300 series also offers modular designs, enabling operators to stack units or configure them in various layouts to optimize space. This adaptability makes these ice makers a smart choice for establishments with limited room or specific design requirements.

In summary, the Hoshizaki KM-1300 series ice makers combine efficiency, durability, and high production rates with advanced technology and user-friendly features. Ideal for high-demand environments, these machines deliver reliable performance and consistent ice quality, making them a valuable asset for any food service operation.
Top Page Image Contents