Hoshizaki KM-1300SAH3, KM-1300SWH3, KM-1300SRH3 service manual Brazing

Page 50

5)Disconnect the vacuum pump, and attach a refrigerant service cylinder to the high-side line. Remember to loosen the connection, and purge the air from the hose. For air-cooled and water- cooled models, see the nameplate for the required refrigerant charge. For remote air-cooled models, see the charge label in the machine compartment. Hoshizaki recommends only virgin refrigerant or reclaimed refrigerant which meets ARI Standard No. 700-88 be used.

6)A liquid charge is recommended for charging an R-404A system. Invert the service

cylinder. Open the high-side, service manifold valve.

7)Allow the system to charge with liquid until the pressures balance.

8)If necessary, add any remaining charge to the system through the low-side. Use a throttling valve or liquid dispensing device to add the remaining liquid charge through the low-side access port with the unit running.

9)Close the two refrigerant access valves and disconnect the hoses and service manifold.

10)Cap the access valves to prevent a possible leak.

2. Brazing

DANGER

1.Refrigerant R-404A itself is not flammable at atmospheric pressure and temperatures up to 176° F.

2.Refrigerant R-404A itself is not explosive or poisonous. However, when exposed to high temperatures (open flames) R-404A can be decomposed to form hydrofluoric acid and carbonyl fluoride both of which are hazardous.

3.Always recover the refrigerant and store it in an approved container. Do not discharge the refrigerant into the atmosphere.

4.Do not use silver alloy or copper alloy containing arsenic.

5.Do not use R-404A as a mixture with pressurized air for leak testing. Refrigerant leaks can be detected by charging the unit with a little refrigerant, raising the pressure with nitrogen and using an electronic leak detector.

Note: All brazing-connections inside the evaporator case are clear-paint coated. Sandpaper the brazing connections before unbrazing the components. Use a good abrasive cloth to remove coating.

50

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Hoshizaki Stackable Crescent Cuber Hoshizaki AMERICA, INC Contents Page Specifications Icemaker KM-1300SAHKM-1300SWH Water Cooled CondenserKM-1300SRH KM-1300SAH3 KM-1300SWH3 KM-1300SRH3 Condensing Unit URC-12FSpecifications Model URC-12F II. General Information Construction KM-1300SAH, KM-1300SAH3KM-1300SWH, KM-1300SWH3 KM-1300SRH, KM-1300SRH3 Solid-State Control Features of Control Products E Controller BoardController Board Controller BoardPage Harvest Cycle Beep every 3 sec. = High Evaporator Temperature 127 FMinute Fill Cycle CycleControl Products HOS-001A Board Sequence 1st Cycle 2nd Cycle and after with pump drain Important Water Valve opening is limited to 6 minutes2nd Cycle and after with no pump drain Controls and Adjustments Dip switch is factory-adjusted to the following positionsSetting Time Setting Frequency Checking the Controller Board Page KM-1300SAH, KM-1300SAH3 KM-1300SWH, KM-1300SWH3 KM-1300SRH, KM-1300SRH3 Wiring Diagrams KM-1300SAH, KM-1300SWHPsig KM-1300SAH3, KM-1300SWH3 Cut-out 412 0 +21.3 Psig Cut-in 327 ± 21.3 Psig Timing Chart Page Performance Data 3271284 1296 1320 1254 1308 IV. Service Diagnosis No Ice Production Problem Possible Cause RemedyProblem Possible Cause Remedy Water Regulator Water Problem Possible Cause Remedy Evaporator is Frozen Up Other Low Ice ProductionAbnormal Ice Refrigerant Recovery Removal and Replacement of ComponentsService for Refrigerant Lines Evacuation and Recharge R-404ABrazing Removal and Replacement of Compressor Removal and Replacement of Drier Removal and Replacement of Expansion Valve Removal and Replacement of Hot Gas Valve and Line Valve Removal and Replacement of Evaporator Page Adjustment of Water Regulating Valve Water-Cooled Model Only Page Removal and Replacement of Thermistor Removal and Replacement of Fan Motor Removal and Replacement of Water Valve Removal and Replacement of Pump MotorRemoval and Replacement of Spray Tubes VI. Maintenance and Cleaning Instructions Preparing the Icemaker for Long StoragePage Cleaning and Sanitizing Procedures Cleaning Procedure Page Sanitizing Procedure Following Cleaning Procedure Maintenance

KM-1300SRH3, KM-1300SWH, KM-1300SRH, KM-1300SAH, KM-1300SWH3 specifications

The Hoshizaki KM-1300 series ice makers are designed to meet the demands of high-volume establishments requiring consistent, high-quality ice production. Among the models in this series are the KM-1300SAH3, KM-1300SWH, KM-1300SRH3, KM-1300SWH3, and KM-1300SAH, each boasting a variety of features and technologies to enhance efficiency and reliability.

One of the standout features of the KM-1300 series is its impressive ice production capacity. Each model is capable of producing up to 1,300 pounds of ice in a 24-hour period, making them ideal for busy restaurants, hotels, or bars that serve a high volume of customers. The machines are designed to create crescent ice, known for its pellet-like texture that is perfect for drink service and food display.

Energy efficiency is another key characteristic of the Hoshizaki KM-1300 models. They are equipped with a highly efficient refrigeration system that minimizes energy consumption while maximizing output. Many of the models in this series are certified by Energy Star, helping operators reduce their environmental footprint and lower operational costs.

Durability and ease of maintenance are also prominent features of the KM-1300 series. Constructed with stainless steel exteriors, these ice makers are built to withstand the rigors of a busy kitchen environment. Additionally, Hoshizaki has incorporated a unique air-cooled condenser design, which reduces the need for frequent servicing and minimizes downtime.

The KM-1300SAH3 and KM-1300SAH models come with advanced touch controls and a user-friendly interface, allowing operators to monitor and adjust settings with ease. The built-in self-diagnostic system alerts users to potential issues before they escalate, improving reliability and ensuring consistent ice production.

For those seeking flexibility, the KM-1300 series also offers modular designs, enabling operators to stack units or configure them in various layouts to optimize space. This adaptability makes these ice makers a smart choice for establishments with limited room or specific design requirements.

In summary, the Hoshizaki KM-1300 series ice makers combine efficiency, durability, and high production rates with advanced technology and user-friendly features. Ideal for high-demand environments, these machines deliver reliable performance and consistent ice quality, making them a valuable asset for any food service operation.
Top Page Image Contents