Henny Penny OFE/OFG-341 To avoid electrical shock or other injury, run, Power terminals

Page 13

 

 

Model OFE/OFG/OEA/OGA-341, 342

2-3. HIGH TEMPERATURE

 

 

LIMIT CONTROL

 

 

(Gas Units) (Continued)

 

 

Replacement

 

To avoid electrical shock or property damage, move the

 

 

power switch to OFF and disconnect main circuit

 

 

breaker, or unplug cord at wall receptacle.

 

1.

If the tube is broken or cracked, the control opens, shutting

 

 

off electrical power to the heat circuit. The control cannot be

 

 

reset, and it continuously clicks when pushed.

 

2.

Drain the shortening from the frypot and discard. A substance

 

 

from the tube could contaminate the shortening.

Figure 2-6

3.

Remove the control panel.

 

4.

Using a 5/16” wrench, loosen small inside screw nut on

 

 

capillary tube. Figure 2-6.

 

5.

Using a 11/16” crows-foot, remove the larger nut securing the

 

 

capillary tube to the pot. Figure 2-7.

Figure 2-7

6.

Remove the two screws securing the high limit guard and

 

remove guard. Figure 2-8

 

7.

Straighten the capillary tube inside the frypot, and pull the

 

 

capillary tube through the frypot, from behind the control

 

 

panel. Remove the defective high limit from the control panel

 

 

area.

 

8.

Replace new high limit in reverse order.

Figure 2-8

 

 

 

 

To avoid electrical shock or other injury, run the

 

 

capillary line under and away from all electrical power

 

 

wires and terminals. The tube must never be in such a

 

 

position where it could accidentally touch the electrical

 

 

power terminals.

1003

 

2-3

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Technical Manual Model OFE/OFG/OEA/OGA-341 FM06-030 Revised Table of Contents Introduction SafetyWhich, if not avoided, could result in death or serious InjuryIf maintenance procedures are not followed correctly TroubleshootingProblem Cause Correction Injuries and/or property damage could resultCleaning the fryer Thoroughly TroubleshootingTroubleshooting Problem Cause Correction Display Cause Panel Board Correction Error CodesError Codes Display Cause Panel Board Correction High Temperature Limit Control Maintenance HintsGas Units Remove the high limit from bracket Remove the two screws securing the high limit to the bracketWires and terminals. The tube must never be in such a Capillary line under and away from all electrical powerPosition where it could accidentally touch the electrical Power terminalsPower Switch Panel ReplacementComplete Control Power Switch Excess force will damage probe Flame SENSOR/ Pilot / Ignitor Assembly GAS Temperature Probe Replacement ElectricFlame SENSOR/ Pilot / Ignitor Assembly Gas Remove the control panel and heat shield from control area Boards Replacement ReplacementTransformer To avoid property damage, do not tamper with, or disassemble Filter Switch Replacement Filter Switch GAS Control Valve Remove screws securing the rear cover to the unit Blower Motor Replacement Heating Elements Electric Blower Motor ReplacementWire Nos Voltage Wattage Ohms cold Heating Checkout Power RemovedContactors 30 31 34 35 36 FigureRe-apply power to unit and turn power switch to on Heating Contactors Electric Replacement Primary ContactorSpeaker Assembly 106 Connect the two electrical wires High TemperatureLimit Control Electric Where it could accidentally touch the electrical power Line under and away from all electrical power wiresTerminals. The tube must never be in such a position TerminalsMotor Removal Filter Pump and Motor Removal Transformer ReplacementAutolift If applicable Actuator Motor ReplacementAutolift Actuator Motor Replacement Install new actuator in reverse order Drain switch wired N/C Drain switch wired N/C Drain switch wired N/C Drain switch wired N/C Drain switch wired N/C Drain switch wired N/C Drain switch wired N/C Drain switch wired N/C Drain switch wired N/O Drain switch wired N/O 707 Drain switch wired N/O Drain switch wired N/O Drain switch wired N/O Drain switch wired N/O 106 Warranty When OrderingParts Information Introduction Genuine PartsItem No Description Qty. per Well Gas Components Gas Burner Assembly Item No Description Qty. per Well Electric Components Item No Description Qty. per Well Item No Description Qty. per Well Model OFE/OFG/OEA/OGA-341 806 Item No Description Qty. per Unit √ recommended parts/*not shown √ recommended parts *not shown Item No Description Qty. per Well 2per well √ recommended parts/*not shown Item No Description Qty. per Well Item No Description Qty. per Well  recommended parts/*not shown OFG/OGA-341 OFG/OGA-342 Item No Description Qty. per Well Part Number Description OFG/OFE Electro Mechanical Parts ListItem No Description Qty ASSY. 341 Faucet DIRECT-CONNECT Parts List Before March 1 DIRECT-CONNECT Parts List Before March 1 Description QtyDescription Qty ROD Extension Filter Valve PIN-COTTER Fitting Connector Male 1209

OEA/OGA-341, OEA/OGA-342, OFE/OFG-341, OFE/OFG-342 specifications

Henny Penny OFE/OFG-341, OEA/OGA-342, OFE/OFG-342, and OEA/OGA-341 are advanced cooking equipment designed primarily for the foodservice industry. These models are part of Henny Penny’s renowned line of pressure fryers, which are celebrated for their ability to deliver consistently high-quality, crispy fried foods while maintaining efficiency and safety.

One of the standout features of these models is their patented pressure frying technology, which allows food to be cooked at higher temperatures and pressures compared to traditional frying methods. This not only reduces cooking time significantly but also helps seal in moisture and flavor, resulting in juicy, tender products with a superior texture. The pressure frying system also uses less oil, making it a more economical choice for busy kitchens.

The OFE/OFG-341 and OFE/OFG-342 models are designed for versatility and ease of use. They offer programmable controls that allow operators to customize cooking times and temperatures for a range of food items, from chicken and fish to vegetables. This adaptability ensures that cooks can achieve the desired results each time, regardless of the menu item. The digital display is user-friendly, allowing staff to navigate through settings with ease.

Safety and maintenance are paramount in these designs. Each model is equipped with a robust safety locking system to prevent accidental opening during the cooking process. Additionally, they feature self-diagnostic capabilities that alert operators to potential issues before they become major problems, thereby reducing downtime.

In terms of construction, Henny Penny's OFE/OFG series is built with durable stainless steel, making them resistant to rust and easy to clean. They also come with an efficient filtration system that prolongs oil life, ensuring that food quality remains high while minimizing costs associated with oil replacement.

Moreover, the OEA/OGA models are designed with energy efficiency in mind. Equipped with advanced heating technology, these fryers conserve energy without compromising performance, making them an environmentally friendly choice.

With precise temperature controls, robust safety mechanisms, and a focus on efficiency, the Henny Penny OFE/OFG-341, OEA/OGA-342, OFE/OFG-342, and OEA/OGA-341 models set a high standard in commercial frying equipment, catering to the needs of modern kitchens while delivering delicious, consistent results.
Top Page Image Contents