Extron electronic MDA 4SV EQ, MDA 4V EQ Rear Panel Features and Cabling, MDA 2V EQ rear panel

Page 10

Installation and Operation, cont’d

3.

Secure the unit to a projector mount or other surface by

 

inserting the mounting bolt through the bracket’s slotted

 

hole.

Rear Panel Features and Cabling

The following figures show the back panel configurations of the three MDA EQ models.

6

 

7

MDA 4SV EQ

INPUT

 

POWER

IN

HIGH Z

12V

0.2A MAX

 

 

75 Ohm

 

LOOP-THRU

OUTPUTSOUTPUTS

1 3

2 4

MDA 2V EQ

INPUT

OUTPUTS

 

 

 

 

 

POWER

IN

HIGH Z

1

4

12V

 

 

 

0.2A MAX

 

 

 

 

 

 

75 Ohm

2

 

1

2

3

 

 

MDA 2V EQ rear panel

6

MDA 4V EQ

INPUT

OUTPUTS

 

 

 

 

POWER

IN

1

3

12V

 

HIGH Z

 

0.2A MAX

 

LOOP-THRU

75 Ohm

2

4

 

 

 

 

1

2

3

 

4

MDA 4V EQ rear panel

1

2

3

5

MDA 4SV EQ rear panel

1Power connector — Plug the external 12 VDC power supply into this 2-pin, 3.5 mm captive screw connector. The power supply is included with the unit.

To wire the connector:

1. Cut the DC output cord to the length needed.

2. Strip the jacket to expose 0.2 inches (5 mm) of the conductors.

Exposing more than 0.2" (5 mm) of the copper wires could allow the stripped wires to touch each other, causing a short circuit. This could result in the external DC power supply overheating and/or burning.

Stripping the wires to expose less than the recommended amount causes them to slide out of the connector too easily, even if they are tightly pinched by the captive screws.

3. Slide the leads into the supplied captive screw plug and lock them, using an Extron Tweeker (small screwdriver).

4. To verify the power cord’s polarity before connecting it, plug in the power supply with no load and check the output with a voltmeter.

The figure on the next page shows how to wire the connector.

2-6

VersaTools® MDA EQ Series • Installation and Operation

VersaTools® MDA EQ Series • Installation and Operation 2-7

Page 9 Page 11
Image 10
Page 9 Page 11
Contents User’s Manual VersaTools Video Mini Distribution AmplifiersExtron’s Warranty PrecautionsFCC Class a Notice Quick Start Guide MDA EQ Series Projector Mounting Bracket Ceiling BoltTable of Contents Introduction Table of Contents, cont’dOne MDA EQ SeriesAbout this Manual IntroductionAbout the MDA EQ Series Mini Distribution Amplifiers Two Installation and OperationIntroduction MDA EQ Series Tabletop use Installation and Operation, cont’dMounting the MDA EQ Series Rack mountingMounting an MDA EQ on a 6-inch rack shelf Projector mountingFurniture mounting Preparing the MDA EQ for under-desk mountingMDA 2V EQ rear panel Rear Panel Features and CablingMDA 4V EQ rear panel MDA 4SV EQ rear panel MDA 2V EQ front panel Front Panel Features and OperationPower connector wiring MDA 4V EQ front panelSpecifications, Part Numbers, and Accessories AAppendix aSpecifications, Parts, and Accessories Optional Accessories Specifications, Parts, and Accessories, cont’d ModelsIncluded Parts
Related manuals
Manual 19 pages 17.74 Kb

MDA 2V EQ, MDA 4SV EQ, MDA 4V EQ specifications

Extron Electronics is renowned for its innovative solutions in the field of professional audiovisual technology. Among its diverse lineup of products, the MDA 2V EQ, MDA 4SV EQ, and MDA 4V EQ stand out as exceptional multi-distribution amplifiers designed to enhance signal processing and distribution in various AV settings.

The MDA 2V EQ is a two-channel distribution amplifier that excels in providing high-quality video and audio signal distribution. It is equipped with advanced equalization capabilities that allow users to fine-tune signal levels for optimal performance over long cable runs. The MDA 2V EQ supports a wide range of video formats, including composite, S-video, and component, ensuring compatibility with various equipment. Its compact design makes it easy to integrate into existing AV setups, while its robust construction ensures reliability in demanding environments.

The MDA 4SV EQ, on the other hand, is a four-channel distribution amplifier specifically designed for S-video signals. This model also features EQ for tailoring the output levels to match varying distances between the source and the display devices. By providing four isolated outputs, it ensures that each connected device receives a clean and undistorted signal. The MDA 4SV EQ is ideal for applications that demand high-quality S-video distribution, such as corporate presentations or educational content delivery.

Meanwhile, the MDA 4V EQ extends Extron’s commitment to versatile AV solutions with its four-channel capability focused on composite video signals. Similar to its counterparts, this model includes built-in EQ, enabling precise signal adjustments. Its ability to drive multiple outputs without compromising signal integrity makes it a perfect choice for situations requiring extensive video distribution.

All three models incorporate Extron’s proprietary technologies, ensuring minimal signal degradation and enhanced performance. They feature user-friendly troubleshooting tools such as LED indicators for signal presence and power status. Additionally, these amplifiers are designed with thermal protection to avoid overheating during extended use.

In summary, the Extron MDA 2V EQ, MDA 4SV EQ, and MDA 4V EQ offer a range of features tailored for optimal video and audio distribution in professional settings. Their advanced signal management technologies, robust performance, and user-friendly design make them invaluable tools for AV professionals looking to achieve high-quality signal distribution in diverse applications.
Top Page Image Contents