Grindmaster Model 3311 manual Consistency Adjustment, Figure J

Page 9

Consistency Adjustment

From time to time, it may become necessary to readjust the consistency setting (thickness) to compensate for variation between different mixes or to switch from one type of product to another. This adjustment is made as follows:

1.Disconnect electrical power.

￿WARNING: Do not attempt to readjust the freezer until electrical power has been disconnected.

2.Remove right side panel (facing the freezer).

3.Use the adjustment screw, situated on the front of the drive motor mounting bracket to change product thickness. Turn the thumbscrew (3 full turns for red spring, 1 turn for yellow spring) to make a noticeable change in consistency. (See Figure K)

NOTE: Clockwise is for thicker product consistency and counter clockwise is for thinner product consistency. (See Figure L)

4.Reinstall the side panel, reconnect power.

5.Turn freezer to “ON” and allow it to freeze to desired consistency.

6.Check product. Repeat process until desired consistency is achieved.

NOTE: When making changes to a colder (thicker) setting, recheck consistency again after the compressor has cycled off. When adjusting (counter-clockwise) to a thinner consistency, a large portion of product must be drawn from the dispense valve to reduce the product thickness below the new set point (adjustment). Then allow the freezer to refreeze product to the new setting.

Mix Low Float O-ring

Carburetor

Mix Low Float

Figure J

Adjustment Screw

Figure K

Increase Thickness

(turn clockwise)

Decrease Thickness

(turn counterclockwise)

Figure L

Model 3311

Page 7

 

 

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Model 3311 Beverage Freezer Manual Page Table of Contents Freezer Application and Specifications OPERATOR’S Safety PrecautionsModel Product TipsCarburetor Assembly Freezer SpecificationsMix Considerations General Shipment Transit InstallationWill cause serious damage to spinner Avoid injuryReview hopper contents to make sure all parts are available Accessory Installation Operation and AdjustmentsHow to Operate Mix Low FunctionFigure J Consistency AdjustmentCare and Cleaning Disassembly and CleaningDrain and Rinse Tight. Do not use tools to tighten knobs Figure CC Insert Retaining Pin Sanitizing and RefillingClean-In-Place Procedure Daily Cleaning MaintenanceSuggested Daily Maintenance Parts Replacement SchedulePreventative Maintenance Procedure Every 6 to 12 Months How to Clean Concealed Filter Air-Cooled Unit Only How to Clean Exposed Filter Air-Cooled Unit OnlyHow to Adjust Belt How to Change Back Lit Sign Merchandiser BulbProblem Probable Cause Remedy General TroubleshootingCheck List Description Item no Exploded View Model 115V Air-Cooled ModelPart Number Description Exploded View Model 220V Air-Cooled ModelExploded View Model 115V Water-Cooled Model Part Description Number Model Base Assembly 115V Air-Cooled ModelPart Number Description Model Base Assembly 220V Air-Cooled ModelModel Base Assembly 115V Water-Cooled Model Model Electrical Box Assembly 115V Model AC/WC Units Model Electrical Box Assembly 220V Air-Cooled Model Model Wiring Diagram 115V Air-Cooled Model Model Wiring Diagram 220V Air-Cooled Model Model Wiring Diagram Water-Cooled Model Model 3311 Compressor Wiring Model Ladder Diagram 115V Air-Cooled Model Model Ladder Diagram 220V Air-Cooled Model Model Ladder Diagram 115V Water-Cooled Model Model 3311 AC/WC Units Spinner Hook-Up 115V Model 220V Model Model Refrigeration 115V Air-Cooled Model Model Refrigeration 220V Air-Cooled Model Model Refrigeration 115V Water-Cooled Model Model Refrigeration Schematic AC Units 115V & 220V Models Model Refrigeration Schematic Water-Cooled Model Model Grindmaster Corporation Form # WH-312-03 W0600110

Model 3311 specifications

The Grindmaster Model 3311 is a state-of-the-art coffee grinder designed for commercial use, particularly favored by coffee shops and restaurants that prioritize precision and consistency in their coffee preparation. This grinder stands out for its robust construction, user-friendly features, and advanced grinding technologies.

One of the main features of the Grindmaster Model 3311 is its high-capacity grinding capabilities. The grinder is equipped with a powerful motor that allows for fast and efficient operation, making it an ideal choice for high-demand environments. It can handle large volumes of beans, grinding them quickly without overheating, which ensures that the coffee's essential flavors and aromas are preserved.

Technologically, the Model 3311 utilizes a set of precision-engineered burrs to achieve uniform particle size. This is crucial because consistent grind size is essential for optimal extraction during brewing, directly impacting the taste and quality of the coffee. The burrs are designed for longevity and can be easily adjusted to customize the grind settings based on the specific needs of different coffee beverages.

Another significant characteristic of the Grindmaster Model 3311 is its intuitive control panel, which allows baristas to easily adjust grind settings and monitor the grinding process. The user-friendly interface features clear indicators and easy-to-use buttons, making it accessible for staff at all skill levels. This design ensures that any operator can quickly become proficient in using the grinder, leading to improved efficiency in busy café environments.

The grinder also features a large bean hopper, capable of holding a considerable amount of coffee beans, which reduces the frequency of refills. This is particularly beneficial during peak service hours, allowing for uninterrupted operation. Additionally, the grind chamber has anti-static technology, minimizing coffee dust and ensuring a clean workspace.

Maintenance is straightforward with the Grindmaster Model 3311, thanks to its accessible design. Regular cleaning and upkeep are essential for maintaining performance, and the model has been engineered to facilitate these tasks without needing extensive disassembly.

In conclusion, the Grindmaster Model 3311 is a remarkable coffee grinder that combines robust performance with user-friendly features. Its high-capacity grinding, advanced burr technology, intuitive controls, and easy maintenance make it a top choice for coffee professionals who demand quality and efficiency. With this grinder, users can expect to deliver exceptional coffee experiences to their customers every time.
Top Page Image Contents