Grindmaster CC-302-20 Cleaning, Drink Strength Adjustment for Model PIC3E or PIC33AE

Page 7
PORTION SIZE ADJUSTMENT
TURN DIAL CLOCKWISE TO INCREASE DISPENSE VOLUME COUNTERCLOCKWISE TO DECREASE DISPENSE VOLUME

Drink Strength Adjustment for Model PIC3E or PIC33AE

when equipped with remote adjust knobs behind drip tray (Refer to Figure C)

1. Dispense a drink to determine if drink is too strong or too weak.

2. Remove drip tray.

3. Using a flat head screwdriver, adjust individual dispense heads by rotating appropriate adjustment knob. Clockwise rotation will result in a stronger drink and counterclockwise rotation will result in a weaker drink.

4.Dispense a drink to determine if drink strength is acceptable, repeat adjustment steps until desired drink strength is achieved.

NOTE: Water flow rate is factory preset at approximately 24mL (0.80 ounces) per second.

Figure C

Drink Strength Adjustment for Model PIC2J & PIC3J (Refer to Figure D)

Tool required: #2 Flat Head screwdriver

1.Dispense a drink to determine if drink is too strong, weak or if portion size is correct.

2.Turn off power to machine at power switch.

3.Drink strength and portion size controls will be found behind the drain tray. (Refer to Figure D) For portion size adjustment, turn dial clockwise to increase dispense volume. To decrease volume turn dial counterclockwise. For drink strength adjustment turn dial clockwise to increase drink strength. To decrease strength turn dial counterclockwise. Turn on power to machine and

dispense a drink to determine if drink strength or portion is acceptable. If drink strength or portion is not acceptable, turn off power to machine and repeat adjustment steps until desired drink strength or portion is achieved.

Note: Clockwise rotation will result in a stronger drink and

DRINK STRENGTH

 

counterclockwise will result in a weaker drink.

 

ADJUSTMENT

 

Note: Water flow rate is factory preset at approximately

TURN DIAL CLOCKWISE TO

 

INCREASE DRINK STRENGTH

 

0.80 ounces per second.

COUNTERCLOCKWISE TO

Figure D

DECREASE STRENGTH

 

*To adjust flow rate, remove left side upper panel. Use flat head screwdriver and turn knob on respective dump valve.

WARNING: Do not adjust flow rate above the factory setting to prevent funnel overflow.

Cleaning

￿CAUTION: When cleaning the unit, do not use cleansers, liquid bleach, powders or any other substance that contains

chlorine. These products promote corrosion of stainless steel and plastic parts. Use of these products will void the warranty.

DAILY

1.Empty the drip pan as needed and wash daily in a solution of dish detergent.

2.Rinse out the whipper chambers by placing the rinse switch (located on the right of the dispensing valves when the door is open) in the “ON” position. Dispense one to two cups until the water is clean. Short bursts of dispensing may also help clean the chambers more effectively. When completed, return the rinse switch to the “OFF” position.

3.Remove the hoppers and refill with product.

Crathco® Powdered Beverage Dispensers

Mixing Funnel Shroud

Water Inlet Fitting

Water Inlet Pipe

Funnel O-Ring

Mixing Funnel

 

 

 

 

 

 

 

 

 

 

Whipper Chamber

 

 

 

 

 

 

 

 

 

 

 

 

 

Whipper Base

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Motor Shaft

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Whipper Base Seal

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Whipper O-Ring

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Whipper Blade

 

 

Dispense Nozzle

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure E

Page 7

Image 7
Contents Crathco Powdered Beverage Dispensers Advertencia Crathco Powdered Beverage Dispensers Water Inlet Connection InstallationStart-up Procedure for Standard Units Start-Up Procedures for Pump Units PIC 2P & PIC 3P onlyAdjustments How to Dispense a Cup of CappuccinoPortion Adjustment Drink Strength Adjustment Thermostat AdjustmentDrink Strength Adjustment for Model PIC3E or PIC33AE CleaningWeekly Reassembling the Hoppers PIC 1/2/3/5/6 Refer to Figure WeeklyQuarterly Cleaning Weekly CleaningPIC Preventative Maintenance Checklist Every 6 to 12 months To Prepare for Shipment ServiceDraining the Tank PIC 2/3/4 230V Whipper Motor Replacement Kit # Quantity Description 120V Whipper Motor Replacement Kit # Quantity DescriptionPurging Machine of All Water for Shipment in Cold Areas Figure Q Removal of Whipper MotorsCrathco Powdered Beverage Dispensers Figure CC Removal of Inlet ValveThermistor Curve Removal of ThermistorRemoval of Heater Relay Removal of Auger MotorsRemoval of Blower Motor Removal of ControllerCrathco Powdered Beverage Dispensers Problem Probable Cause Corrective Action Troubleshooting GuideTroubleshooting Guide PIC 1 Chassis Parts PIC 1 Hopper Bracket PIC 1 Door Assembly Units with serial numbers beginning with L or T PIC 1 Tank AssemblyUnits with serial numbers beginning with T $2!7.Ĥ 63097 PIC 2/3 Chassis Parts PIC 2/3 Hopper Bracket PIC 2/3 Tank Assembly PIC 2/3 Door Assembly PIC 4 Chassis Parts Base PIC 4 Control Bracket AssemblyPIC43A Control Bracket Assembly PIC 4 Hopper Bracket PIC 4 Hopper OHPHQW PIC 4 Tank AssemblyPIC 4 Door Assembly PIC 4 Final Assembly PIC 5 Base Assembly PIC 5 Casing AssemblyItem NO. Part NO. Description PIC 5 Door AssemblyHopper Brkt Asy PIC5 PIC 5 Hopper Bracket AssemblyCrathco Powdered Beverage Dispensers PIC5 Final Assembly PIC 5 Final Assembly62874 PIC 6 Casing AssemblyPIC 6 Lid Assembly PIC 6 Base Assembly 62876PIC 6 Door Assembly PIC 5/6 Control Bracket Assembly62863 PIC 6 Hopper Bracket AssemblyPIC 6 Final Assembly PIC 1 120V and 120/240V Q Model Wiring PIC 1 230V E Model Wiring PIC1KE or PIC1KAE, 230V E Model Wiring PIC1K or PIC1KA 120 & 120/240 Q Model Wiring PIC1KAEW or PIC1KEW Wiring CAP1AE or CAP1E 230V E Model Wiring PIC 2/3 120 & 120/240V Q Model Wiring Crathco Powdered Beverage Dispensers PIC33AE 230V CE Model Wiring with 3-Portion Touch Pads PIC 2/3 100 & 200V J Model Wiring Crathco Powdered Beverage Dispensers Crathco Powdered Beverage Dispensers PIC 4 Wiring PIC43A 120V & PIC43AQ 120/240V Wiring PIC43AZ and PIC43AWZ Model Wiring with 3-Portion Touchpad PIC4Z, PIC4AZ, PIC4WZ, PIC4AWZ 240V Model Wiring PIC 5/6 Wiring Crathco Powdered Beverage Dispensers Grindmaster Corporation

CC-302-20 specifications

The Grindmaster CC-302-20 is a highly regarded coffee brewing machine designed for cafes and restaurants that require both quality and efficiency. This model stands out for its user-friendly features and advanced brewing technology, making it a popular choice among coffee enthusiasts and professionals alike.

One of the main features of the Grindmaster CC-302-20 is its programmable brewing cycles. This allows operators to customize brew times and temperatures according to their specific coffee offerings. The machine can brew up to 3 gallons of coffee per cycle, ensuring that businesses can meet high demand during peak hours without compromising on quality.

A significant characteristic of the CC-302-20 is its digital display, which provides real-time information on brewing status and alerts for maintenance needs. This feature ensures that users can monitor the brewing process at a glance, minimizing the chance of over-brewing or under-brewing coffee. The machine also includes an automatic shut-off function, which enhances energy efficiency and safety.

The Grindmaster CC-302-20 incorporates advanced brewing technology, notably its precision temperature control system. This system guarantees that water is heated to the optimal brewing temperature, which is crucial for maximizing the extraction of coffee flavors. This feature is particularly beneficial for cafes that pride themselves on serving high-quality, flavorful coffee.

Additionally, the CC-302-20 is designed with a durable, stainless steel construction, ensuring long-lasting performance in busy commercial environments. Its compact footprint makes it suitable for various countertop sizes, while the sleek design contributes to an appealing aesthetic in any coffee shop or restaurant.

Maintenance is another critical aspect of the Grindmaster CC-302-20. The machine is engineered for easy access to components, making it simple for staff to clean and service as needed. Regular maintenance routines can help extend the life of the equipment and maintain optimum brewing performance.

In conclusion, the Grindmaster CC-302-20 coffee brewer is an exceptional choice for establishments seeking a reliable, efficient, and high-quality brewing solution. Its programmable features, precision temperature control, and durable design make it an investment that meets the demands of busy coffee environments while consistently delivering delicious brews.