Jackson JP-24BPNSU technical manual Installation & Operation Instructions

Page 17

SECTION 2: INSTALLATION & OPERATION INSTRUCTIONS

OPERATION INSTRUCTIONS

PREPARATION: Before proceeding with the start-up of the unit, verify the following:

1.The strainer is in place and is clean.

2.That the wash and rinse arms are screwed securely into place and that their endcaps are tight. The wash and rinse arms should rotate freely.

POWER UP: To energize the unit, turn on the power at the service breaker. The voltage should have been previously verified as being correct. If not, the voltage will have to be verified.

FILLING THE WASH TUB:For the initial fill, close the door and depress the ON/FILL-OFF/DRAIN rocker switch in the ON posi- tion. The machine will run a partial cycle and fill to the factory preset level. Open the door and verify that the water level is correct. Hereafter, the water level is controlled by the timer that has been preset at the factory. Verify that there are no other leaks on the unit before proceeding any further. The wash tub must be completely filled before operating the wash pump to pre- vent damage to the component. Once the wash tub is filled, the unit is ready for operation.

NOTE: Make sure the orange wires at the heater contactor are connected properly. They have been purposely disconnected at the factory to avoid damage to the heater element when there is no water in the booster heater.

The machine runs a complete cycle to drain and fill. If the machine is not allowed to drain, the water will build up inside the tub. After the initial fill, the rinse water for the current cycle will become the wash water for the next cycle.

WARE PREPARATION: Proper preparation of ware will help ensure good results and less re-washes. If not done properly, ware may not come out clean and the efficiency of the dishmachine will be reduced. It is important to remember that a dishmachine is not a garbage disposal and that simply throwing unscraped dishes into the machine simply defeats the purpose altogether of washing the ware. Scraps should be removed from ware prior to being loaded into a rack. Pre-rinsing and pre-soaking are good ideas, especially for silverware and casserole dishes. Place cups and glasses upside down in racks so that they do not hold water during the cycle. The dishmachine is meant not only to clean, but to sanitize as well, to destroy all of the bacteria that could be harmful to human beings. In order to do this, ware must be properly prepared prior to being placed in the machine.

DAILY MACHINE PREPARATION: Refer to the section entitled “PREPARATION” at the top of this page and follow the instruc- tions there. Afterwards, check that all of the chemical levels are correct and/or that there is plenty of detergent available for the expected workload.

WARM-UP CYCLES: For a typical daily start-up, it is recommended to run the machine through 3 cycles to ensure that all of the cold water is out of the system and to verify that the unit is operating correctly. To cycle the machine, ensure that the power is on and that the tub has filled to the correct level. Open the door and the cycle light will illuminate. When the light goes out, close the door, the unit will start, run through the cycle, and shut off automatically. Repeat this two more times. The unit should now be ready to proceed with the washing of ware.

WASHING A RACK OF WARE: To wash a rack, open the door completely and slide the rack into the unit. Close the door and the unit will start automatically. Once the cycle is completed, open the door and remove the rack of clean ware. Replace with a rack of soiled ware and close the door. The process will then repeat itself.

OPERATIONAL INSPECTION: Based upon usage, the pan strainer may become clogged with soil and debris as the workday progresses. Operators should regularly inspect the pan strainer to ensure it has not become clogged. If the strainer does, it will reduce the washing capability of the machine. Instruct operators to clean out the pan strainer at regular intervals or as required by work load.

SHUTDOWN AND CLEANING: At the end of the workday, close the door. Start a cycle, then place the ON/FILL - OFF/DRAIN SWITCH to the “ OFF/DRAIN” position. The unit will automatically drain and turn off. Once the wash tub is drained, remove he pan strainer. Remove soil and debris from the strainer and set to the side. Unscrew the wash and rinse arms from their mani- folds. Remove the endcaps and flush the arms with water. Use a brush to clean out the inside of the arms. If the nozzles appear to be clogged, use a toothpick to remove the obstruction. Wipe the inside of the unit out, removing all soil and scraps. Reassemble the wash and rinse arms and replace them in the unit. The arms only need to be hand tight, do not use tools to tighten them down. Reinstall the strainer and close the door.

JP-24BPNSU Technical Manual

7610-002-38-50 Rev. D (11/11/2005)

9

Image 17
Contents JP-24BPNSU Technical ManualManufacturers Warranty ONE Year Limited Parts & Labor WarrantyRevision Made Applicable Details Date ECN Nomenclature for the Model Covered in this Manual Model Serial No Installation Date Service Rep. Name Phone NoDLA-400-90-M-1376 Approval and Procurement Record Approval Data forContract no NSN NO. of Units CID/APL Change Record Additional Identification if any Not applicable Identifying Technical Publication SheetPurchase Order or Contract NO. DLA-400-90-M-1376 VII Electrical Schematics II. Installation & Operation InstructionsTmder Sheets Viii Jackson Maintenance and Repair Centers Parts SectionSection Specification Information Frame Dimensions Wash Pump Capacity Volts Hertz Phase Heater Motor Total Glasses PER HourTemperatures Ratings22 5/8 Specification Information DimensionsSection INSTALLATION/OPERATION Instructions Drain Hose Terminal Block Ground Lug Typical Location Foot Front View Floor Leveler Installation & Operation Instructions Detergent Control Installation & Operation Instructions Section Preventative Maintenance Preventative Maintenance Section Troubleshooting Problem Water overflow from bottom of door Troubleshooting Section Common ProblemsProblem Wash motor doesn’t operate on manual wash Problem Motor operates on manual wash but not on automaticProblem No indication of pressure Problem Rinse water not at required temperature rangeSection Service Procedures Steps Service Procedures Rinse Solenoid Valve Repair Parts KITPreparation Tools RequiredRemove the wire nuts from the wires and separate them Removing the valve bonnet Special Parts After Maintenance ActionsSet the cap to the side Service Procedures Vacuum Breaker Repair Parts KITRemoving the plunger Replacing the Booster Tank Heater Minal on the Motor Service Procedures Replacing the Drain ValveSection Parts Section Mfg. No Parts Section Electrical Panel AssemblyQTY Description Parts Section Gauge Panel Assembly Parts Section Kick Plate Assembly Parts Section Incoming Plumbing Assembly QTY Description Parts Section Plumbing Assembly Parts Section Plumbing Assembly Retainer 06401-003-07-41 Screen Parts Section Drain Valve Assembly QTY Description Parts Section Drain Plumbing Assembly QTY Description Parts Section Wash Motor to Wash TUB Assembly Parts Section Wash Motor Assembly 40F Rise Parts Section Rinse Tank & ComponentsParts Section Door Assembly Parts Section Miscellaneous Door SUB-ASSEMBLIES Door Latch AssemblyParts Section Rinse ARM & Wash ARM Assemblies Rinse Arm AssemblyWash Arm Assembly Parts Section Miscellaneous Parts Parts Section FRAME, SHROUD, & Panel Components Section Electrical Diagrams 9905-031-51-11 Navsea S0005-AA-GYD-030/TMMP Fold Here Department of the Navy Place Postage Here Navsea S0005-AA-GYD-030/TMMP Fold Here Department of the Navy Place Postage Here Jackson Maintenance Repair Centers Alaska Jackson Maintenance & Repair Centers AlabamaArizona ArkansasHawaii Jackson Maintenance & Repair Centers Georgia to MarylandIdaho IllinoisMassachusetts Jackson Maintenance & Repair Centers Maryland to NEW YorkMichigan MinnesotaNorth Carolina North DakotaOhio OklahomaUtah South CarolinaRhode Island South DakotaWyoming VirginiaWashington West Virginia

JP-24BPNSU specifications

The Jackson JP-24BPNSU is a striking electric guitar that caters to a wide range of musical genres, from rock to metal. Known for its exceptional playability and innovative design, this instrument stands out not only in appearance but also in performance.

At the heart of the JP-24BPNSU is its solid body, which is crafted from high-quality basswood. This lightweight tonewood contributes to the guitar's resonant sound while ensuring comfort during extended playing sessions. With a sleek, contoured design, the body allows for easy reach across the fretboard, making it an ideal choice for players who favor speed and agility.

The guitar features a unique bolt-on maple neck that offers stability and enhances sustain, paired with a rosewood fingerboard for a warm tonal quality. With 24 jumbo frets, the JP-24BPNSU provides ample space for intricate licks and solos, catering to both beginners and advanced players. Its 25.5-inch scale length contributes to a tight, focused sound that is perfect for aggressive playing styles.

One of the standout features of this guitar is its high-output Jackson humbucking pickups. These pickups deliver powerful tones with excellent clarity, making them suitable for various musical styles. They are designed to handle high levels of gain, allowing performers to achieve thick, saturated sounds without muddiness. The JP-24BPNSU also features a versatile three-way pickup selector switch, providing players with options to explore different tonal palettes effortlessly.

In terms of hardware, the guitar comes equipped with a high-quality licensed Floyd Rose tremolo system. This allows for dramatic pitch bending and dive-bombing effects while maintaining tuning stability, which is essential for many modern guitar techniques. The guitar's reliable tuning machines further enhance its performance, ensuring that your instrument stays in tune even after intense playing sessions.

Aesthetically, the Jackson JP-24BPNSU is designed to catch the eye. It often boasts a bold finish combined with striking body contours, making it a visually appealing choice for performers. The cutting-edge craftsmanship and attention to detail not only provide an attractive look but also ensure durability and longevity.

Overall, the Jackson JP-24BPNSU is an ideal electric guitar for musicians seeking a blend of style, tone, and performance. With its range of features and technologies, it is well-suited for both studio work and live performances. Whether you are a beginner or a seasoned player, the JP-24BPNSU offers an exceptional playing experience that is sure to inspire creativity and enhance your musical journey.