Jackson JP-24BPNSU technical manual Removing the plunger

Page 29

SECTION 5: SERVICE PROCEDURES

VACUUM BREAKER REPAIR PARTS KIT (CONTINUED)

Removing the plunger

6.Your repair kit comes with a new plunger. Examine the old one and ensure that the mating surface is not damaged or cut. Also inspect the rubber seal on the top of the plunger to ensure it is in good condition and not torn.

Examining the seal ring on the plunger

7.If any of these conditions are present, replace the old plunger with the new one from your kit. Verify that the new plunger is also free from defects. If it is not, contact your Ecolab representative immediately.

8.The plunger should drop into the vacuum breaker and seat. Ensure it is not flipped upside down (the orange seal ring should be up towards the top of the vacuum breaker).

9.Pick up the cap and examine it. With a soft towel, remove any grit, grime or debris that may have gotten caught in the threads of both the cap retainer or the vacuum breaker body. There is an O-ring that should be present on the cap retainer as well. Regardless of the condition of the plunger, this O-ring should be replaced once the cap is removed. Using a small flathead screwdriver, remove the old O-ring.

Replacing the O-ring

10.With the new O-ring in place, screw the cap back on the vacuum breaker body. The cap needs to only be hand tight (snug).

AFTER MAINTENANCE ACTIONS

1. Reconnect the incoming water (if disconnected) and turn on. Then restore power to the unit. Run the unit for at least 10 minutes to ensure there are no leaks. If any prob- lems arise please contact Jackson.

SPECIAL PARTS

To order the kit with components and instructions:

Components of 1/2” Repair Kit 06401-003-06-23

Examining the plunger seating surface

JP-24BPNSU Technical Manual

7610-002-38-50 Rev. D (11/11/2005)

21

Page 28 Page 30
Image 29
Page 28 Page 30
Contents JP-24BPNSU Technical ManualManufacturers Warranty ONE Year Limited Parts & Labor WarrantyRevision Made Applicable Details Date ECN Nomenclature for the Model Covered in this Manual Model Serial No Installation Date Service Rep. Name Phone NoDLA-400-90-M-1376 Approval and Procurement Record Approval Data forContract no NSN NO. of Units CID/APL Change Record Additional Identification if any Not applicable Identifying Technical Publication SheetPurchase Order or Contract NO. DLA-400-90-M-1376 VII Electrical Schematics II. Installation & Operation InstructionsTmder Sheets Viii Jackson Maintenance and Repair Centers Parts SectionSection Specification Information Frame Dimensions Wash Pump Capacity Volts Hertz Phase Heater Motor Total Glasses PER HourTemperatures Ratings22 5/8 Specification Information DimensionsSection INSTALLATION/OPERATION Instructions Drain Hose Terminal Block Ground Lug Typical Location Foot Front View Floor Leveler Installation & Operation Instructions Detergent Control Installation & Operation Instructions Section Preventative Maintenance Preventative Maintenance Section Troubleshooting Problem Water overflow from bottom of door Troubleshooting Section Common ProblemsProblem Wash motor doesn’t operate on manual wash Problem Motor operates on manual wash but not on automaticProblem No indication of pressure Problem Rinse water not at required temperature rangeSection Service Procedures Steps Service Procedures Rinse Solenoid Valve Repair Parts KITPreparation Tools RequiredRemove the wire nuts from the wires and separate them Removing the valve bonnet Special Parts After Maintenance ActionsSet the cap to the side Service Procedures Vacuum Breaker Repair Parts KITRemoving the plunger Replacing the Booster Tank Heater Minal on the Motor Service Procedures Replacing the Drain ValveSection Parts Section Mfg. No Parts Section Electrical Panel AssemblyQTY Description Parts Section Gauge Panel Assembly Parts Section Kick Plate Assembly Parts Section Incoming Plumbing Assembly QTY Description Parts Section Plumbing Assembly Parts Section Plumbing Assembly Retainer 06401-003-07-41 Screen Parts Section Drain Valve Assembly QTY Description Parts Section Drain Plumbing Assembly QTY Description Parts Section Wash Motor to Wash TUB Assembly Parts Section Wash Motor Assembly 40F Rise Parts Section Rinse Tank & ComponentsParts Section Door Assembly Parts Section Miscellaneous Door SUB-ASSEMBLIES Door Latch AssemblyParts Section Rinse ARM & Wash ARM Assemblies Rinse Arm AssemblyWash Arm Assembly Parts Section Miscellaneous Parts Parts Section FRAME, SHROUD, & Panel Components Section Electrical Diagrams 9905-031-51-11 Navsea S0005-AA-GYD-030/TMMP Fold Here Department of the Navy Place Postage Here Navsea S0005-AA-GYD-030/TMMP Fold Here Department of the Navy Place Postage Here Jackson Maintenance Repair Centers Alaska Jackson Maintenance & Repair Centers AlabamaArizona ArkansasHawaii Jackson Maintenance & Repair Centers Georgia to MarylandIdaho IllinoisMassachusetts Jackson Maintenance & Repair Centers Maryland to NEW YorkMichigan MinnesotaNorth Carolina North DakotaOhio OklahomaUtah South CarolinaRhode Island South DakotaWyoming VirginiaWashington West Virginia

JP-24BPNSU specifications

The Jackson JP-24BPNSU is a striking electric guitar that caters to a wide range of musical genres, from rock to metal. Known for its exceptional playability and innovative design, this instrument stands out not only in appearance but also in performance.

At the heart of the JP-24BPNSU is its solid body, which is crafted from high-quality basswood. This lightweight tonewood contributes to the guitar's resonant sound while ensuring comfort during extended playing sessions. With a sleek, contoured design, the body allows for easy reach across the fretboard, making it an ideal choice for players who favor speed and agility.

The guitar features a unique bolt-on maple neck that offers stability and enhances sustain, paired with a rosewood fingerboard for a warm tonal quality. With 24 jumbo frets, the JP-24BPNSU provides ample space for intricate licks and solos, catering to both beginners and advanced players. Its 25.5-inch scale length contributes to a tight, focused sound that is perfect for aggressive playing styles.

One of the standout features of this guitar is its high-output Jackson humbucking pickups. These pickups deliver powerful tones with excellent clarity, making them suitable for various musical styles. They are designed to handle high levels of gain, allowing performers to achieve thick, saturated sounds without muddiness. The JP-24BPNSU also features a versatile three-way pickup selector switch, providing players with options to explore different tonal palettes effortlessly.

In terms of hardware, the guitar comes equipped with a high-quality licensed Floyd Rose tremolo system. This allows for dramatic pitch bending and dive-bombing effects while maintaining tuning stability, which is essential for many modern guitar techniques. The guitar's reliable tuning machines further enhance its performance, ensuring that your instrument stays in tune even after intense playing sessions.

Aesthetically, the Jackson JP-24BPNSU is designed to catch the eye. It often boasts a bold finish combined with striking body contours, making it a visually appealing choice for performers. The cutting-edge craftsmanship and attention to detail not only provide an attractive look but also ensure durability and longevity.

Overall, the Jackson JP-24BPNSU is an ideal electric guitar for musicians seeking a blend of style, tone, and performance. With its range of features and technologies, it is well-suited for both studio work and live performances. Whether you are a beginner or a seasoned player, the JP-24BPNSU offers an exceptional playing experience that is sure to inspire creativity and enhance your musical journey.
Top Page Image Contents