Jackson JP-24BPNSU technical manual Replacing the Booster Tank Heater

Page 30
Hex Nuts & Washers
Replacing the Heater

SECTION 5: SERVICE PROCEDURES

REPLACING THE PUMP MOTOR/REPLACING THE HEATER

REPLACING THE PUMP MOTOR

The following list of tools will be needed to complete this procedure. 5/6” nutdriver, phillips screwdriver, 7/16” socket and ratchet, and 7/16” wrench.

1.Disconnect the electrical power to the dishwasher at the main circuit breaker box when servicing. Place a tag on the cir- cuit box indicating the circuit is being repaired.

2.Disconnect power and conduit from dishmachine terminal block.

3.Turn off the water supply and disconnect the water supply line.

4.Disconnect the dishmachine drain hose from the kitchen’s

drain. Drain the machine of any water at this time.

 

5. Move the machine out and lay machine onto its back.

 

6. Use a 5/16” nutdriver to loosen the hose clamp and remove

8

the pump hose to the drain valve.

 

7. Use a 5/16” nutdriver to loosen the hose clamp and remove

6

the pump hose from the suction casting.

 

8. Use a 5/16” nutdriver to loosen the hose clamp and remove

 

the pump hose from the discharge hub casting.

 

9. Use a 7/16” socket and ratchet, and a 7/16” wrench to

 

remove the drain valve mounting bracket from the motor brack-

 

et.

 

10. Use a 7/16” socket and ratchet to remove the pump motor

 

assembly by loosening the (4) locknuts securing the motor

10

mounting bracket. NOTE: The motor mounting bracket is slot-

9

ted to allow for easy removal and installation. Remove (2) of the

7

locknuts on one side and slide the assembly toward that side

 

and remove. Once the assembly is removed, disconnect the

 

wire leads from the motor wiring box.

 

11. Install replacement motor in reverse order of above.

 

 

Replacing the Pump Motor

REPLACING THE BOOSTER TANK HEATER

The following list of tools will be needed to complete this procedure: phillips screwdriver and 1/2” socket and ratchet.

1.Disconnect the electrical power to the dishwasher at the main circuit breaker box when servicing. Place a tag on the cir- cuit box indicating the circuit is being repaired.

2.Use the phillips screwdriver to remove the two screws from the bottom of the kick panel.

3.Disconnect power and conduit from dishmachine terminal block.

4.Turn off the water supply to the dishmachine.

5.VERY IMPORTANT: Disconnect wire lead (orange/white) from heater contactor coil. Note: Wire is tagged in electrical

panel.

 

6.

Drain water from booster tank.

 

7.

Remove the wires from the heater.

Heater Gasket

8.

Use a 1/2” socket and ratchet to remove the (4) 5/16-18 hex

 

nuts and lock washers. Remove the heater and heater gasket

Heater

from booster tank.

 

8.

Install the replacement heater and gasket, the tighten firmly.

 

9.

Connect wire leads to heater and tighten firmly.

 

10.Turn on water supply and power to dishmachine.

11.Place cycle switch in AUTO position and depress power

switch to ON/FILL position.

12. VERY IMPORTANT: Run the dishmachine through several complete cycles and check water level in wash sump. If there is water in the wash sump, reconnect the wire lead (orange/white) previously removed from the heater contactor coil.

13. Run the dishwasher through several cycles and check to see that rinse and wash temperatures are correct.

JP-24BPNSU Technical Manual

7610-002-38-50 Rev. D (11/11/2005)

22

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Technical Manual JP-24BPNSUONE Year Limited Parts & Labor Warranty Manufacturers WarrantyRevision Made Applicable Details Date ECN Model Serial No Installation Date Service Rep. Name Phone No Nomenclature for the Model Covered in this ManualApproval and Procurement Record Approval Data for Contract no NSN NO. of Units CID/APLDLA-400-90-M-1376 Change Record Identifying Technical Publication Sheet Purchase Order or Contract NO. DLA-400-90-M-1376Additional Identification if any Not applicable Tmder Sheets Viii Jackson Maintenance and Repair Centers II. Installation & Operation InstructionsVII Electrical Schematics Parts SectionSection Specification Information Temperatures Volts Hertz Phase Heater Motor Total Glasses PER HourFrame Dimensions Wash Pump Capacity RatingsSpecification Information Dimensions 22 5/8Section INSTALLATION/OPERATION Instructions Drain Hose Terminal Block Ground Lug Typical Location Foot Front View Floor Leveler Installation & Operation Instructions Detergent Control Installation & Operation Instructions Section Preventative Maintenance Preventative Maintenance Section Troubleshooting Problem Wash motor doesn’t operate on manual wash Troubleshooting Section Common ProblemsProblem Water overflow from bottom of door Problem Motor operates on manual wash but not on automaticProblem Rinse water not at required temperature range Problem No indication of pressureSection Service Procedures Preparation Service Procedures Rinse Solenoid Valve Repair Parts KITSteps Tools RequiredRemove the wire nuts from the wires and separate them Removing the valve bonnet After Maintenance Actions Special PartsService Procedures Vacuum Breaker Repair Parts KIT Set the cap to the sideRemoving the plunger Replacing the Booster Tank Heater Service Procedures Replacing the Drain Valve Minal on the MotorSection Parts Section Parts Section Electrical Panel Assembly QTY DescriptionMfg. No Parts Section Gauge Panel Assembly Parts Section Kick Plate Assembly Parts Section Incoming Plumbing Assembly QTY Description Parts Section Plumbing Assembly Parts Section Plumbing Assembly Retainer 06401-003-07-41 Screen Parts Section Drain Valve Assembly QTY Description Parts Section Drain Plumbing Assembly QTY Description Parts Section Wash Motor to Wash TUB Assembly Parts Section Wash Motor Assembly Parts Section Rinse Tank & Components 40F RiseParts Section Door Assembly Door Latch Assembly Parts Section Miscellaneous Door SUB-ASSEMBLIESRinse Arm Assembly Wash Arm AssemblyParts Section Rinse ARM & Wash ARM Assemblies Parts Section Miscellaneous Parts Parts Section FRAME, SHROUD, & Panel Components Section Electrical Diagrams 9905-031-51-11 Navsea S0005-AA-GYD-030/TMMP Fold Here Department of the Navy Place Postage Here Navsea S0005-AA-GYD-030/TMMP Fold Here Department of the Navy Place Postage Here Jackson Maintenance Repair Centers Arizona Jackson Maintenance & Repair Centers AlabamaAlaska ArkansasIdaho Jackson Maintenance & Repair Centers Georgia to MarylandHawaii IllinoisMichigan Jackson Maintenance & Repair Centers Maryland to NEW YorkMassachusetts MinnesotaOhio North DakotaNorth Carolina OklahomaRhode Island South CarolinaUtah South DakotaWashington VirginiaWyoming West Virginia

JP-24BPNSU specifications

The Jackson JP-24BPNSU is a striking electric guitar that caters to a wide range of musical genres, from rock to metal. Known for its exceptional playability and innovative design, this instrument stands out not only in appearance but also in performance.

At the heart of the JP-24BPNSU is its solid body, which is crafted from high-quality basswood. This lightweight tonewood contributes to the guitar's resonant sound while ensuring comfort during extended playing sessions. With a sleek, contoured design, the body allows for easy reach across the fretboard, making it an ideal choice for players who favor speed and agility.

The guitar features a unique bolt-on maple neck that offers stability and enhances sustain, paired with a rosewood fingerboard for a warm tonal quality. With 24 jumbo frets, the JP-24BPNSU provides ample space for intricate licks and solos, catering to both beginners and advanced players. Its 25.5-inch scale length contributes to a tight, focused sound that is perfect for aggressive playing styles.

One of the standout features of this guitar is its high-output Jackson humbucking pickups. These pickups deliver powerful tones with excellent clarity, making them suitable for various musical styles. They are designed to handle high levels of gain, allowing performers to achieve thick, saturated sounds without muddiness. The JP-24BPNSU also features a versatile three-way pickup selector switch, providing players with options to explore different tonal palettes effortlessly.

In terms of hardware, the guitar comes equipped with a high-quality licensed Floyd Rose tremolo system. This allows for dramatic pitch bending and dive-bombing effects while maintaining tuning stability, which is essential for many modern guitar techniques. The guitar's reliable tuning machines further enhance its performance, ensuring that your instrument stays in tune even after intense playing sessions.

Aesthetically, the Jackson JP-24BPNSU is designed to catch the eye. It often boasts a bold finish combined with striking body contours, making it a visually appealing choice for performers. The cutting-edge craftsmanship and attention to detail not only provide an attractive look but also ensure durability and longevity.

Overall, the Jackson JP-24BPNSU is an ideal electric guitar for musicians seeking a blend of style, tone, and performance. With its range of features and technologies, it is well-suited for both studio work and live performances. Whether you are a beginner or a seasoned player, the JP-24BPNSU offers an exceptional playing experience that is sure to inspire creativity and enhance your musical journey.
Top Page Image Contents