Jackson JP-24BPNSU technical manual Remove the wire nuts from the wires and separate them

Page 25

SECTION 5: SERVICE PROCEDURES

RINSE SOLENOID VALVE REPAIR PARTS KIT (CONTINUED)

Prying open the coil wire cover

4.When replacing the coil, ensure that when removing the coil wire cover that care is taken not to damage the wires inside. Using the medium flathead screwdriver, gently use it to open the cover enough to where it could be pulled off.

Straightening the wires

5.Once the coil wire cover has been removed and set to the side, take the internal wires and pull them out straight.

Removing the wire nuts

6. Remove the wire nuts from the wires and separate them.

Loosening the conduit nut

7.Using a pair of channel locks, gently loosen the conduit retaining ring for the conduit nut. Once it is loosened, use your fingers to unscrew and remove it.

8.Pull the conduit away and discard the bad coil. Take the new coil and attach the conduit, reinstall & tighten the conduit nut, and pull the wires through so that you will be able to wire the valve back up.

9.Reconnect the wires from the conduit to the wires from the solenoid as they had been connected previously. Ensure that the wire nuts are on tight.

10.Slide the coil wire cover back on, taking care not to dam- age the wires.

11.If you are done performing maintenance on the valve, con- tinue on to step 23. Otherwise, please go on to step 12.L

Loosening the valve bonnet

12.To remove the valve bonnet, grasp it with the jaws of the pipe wrench and turn to the left. Note: on some models you may have to remove the valve in order to perform this and any further steps. Be careful not to damage the plumbing assem- bly. Only use the pipe wrench enough to where you can spin the valve bonnet off with your hand.

JP-24BPNSU Technical Manual 7610-002-38-50 Rev. D (11/11/2005)

17

Page 24 Page 26
Image 25
Page 24 Page 26
Contents JP-24BPNSU Technical ManualManufacturers Warranty ONE Year Limited Parts & Labor WarrantyRevision Made Applicable Details Date ECN Nomenclature for the Model Covered in this Manual Model Serial No Installation Date Service Rep. Name Phone NoContract no NSN NO. of Units CID/APL Approval and Procurement Record Approval Data forDLA-400-90-M-1376 Change Record Purchase Order or Contract NO. DLA-400-90-M-1376 Identifying Technical Publication SheetAdditional Identification if any Not applicable VII Electrical Schematics II. Installation & Operation InstructionsTmder Sheets Viii Jackson Maintenance and Repair Centers Parts SectionSection Specification Information Frame Dimensions Wash Pump Capacity Volts Hertz Phase Heater Motor Total Glasses PER HourTemperatures Ratings22 5/8 Specification Information DimensionsSection INSTALLATION/OPERATION Instructions Drain Hose Terminal Block Ground Lug Typical Location Foot Front View Floor Leveler Installation & Operation Instructions Detergent Control Installation & Operation Instructions Section Preventative Maintenance Preventative Maintenance Section Troubleshooting Problem Water overflow from bottom of door Troubleshooting Section Common ProblemsProblem Wash motor doesn’t operate on manual wash Problem Motor operates on manual wash but not on automaticProblem No indication of pressure Problem Rinse water not at required temperature rangeSection Service Procedures Steps Service Procedures Rinse Solenoid Valve Repair Parts KITPreparation Tools RequiredRemove the wire nuts from the wires and separate them Removing the valve bonnet Special Parts After Maintenance ActionsSet the cap to the side Service Procedures Vacuum Breaker Repair Parts KITRemoving the plunger Replacing the Booster Tank Heater Minal on the Motor Service Procedures Replacing the Drain ValveSection Parts Section QTY Description Parts Section Electrical Panel AssemblyMfg. No Parts Section Gauge Panel Assembly Parts Section Kick Plate Assembly Parts Section Incoming Plumbing Assembly QTY Description Parts Section Plumbing Assembly Parts Section Plumbing Assembly Retainer 06401-003-07-41 Screen Parts Section Drain Valve Assembly QTY Description Parts Section Drain Plumbing Assembly QTY Description Parts Section Wash Motor to Wash TUB Assembly Parts Section Wash Motor Assembly 40F Rise Parts Section Rinse Tank & ComponentsParts Section Door Assembly Parts Section Miscellaneous Door SUB-ASSEMBLIES Door Latch AssemblyWash Arm Assembly Rinse Arm AssemblyParts Section Rinse ARM & Wash ARM Assemblies Parts Section Miscellaneous Parts Parts Section FRAME, SHROUD, & Panel Components Section Electrical Diagrams 9905-031-51-11 Navsea S0005-AA-GYD-030/TMMP Fold Here Department of the Navy Place Postage Here Navsea S0005-AA-GYD-030/TMMP Fold Here Department of the Navy Place Postage Here Jackson Maintenance Repair Centers Alaska Jackson Maintenance & Repair Centers AlabamaArizona ArkansasHawaii Jackson Maintenance & Repair Centers Georgia to MarylandIdaho IllinoisMassachusetts Jackson Maintenance & Repair Centers Maryland to NEW YorkMichigan MinnesotaNorth Carolina North DakotaOhio OklahomaUtah South CarolinaRhode Island South DakotaWyoming VirginiaWashington West Virginia

JP-24BPNSU specifications

The Jackson JP-24BPNSU is a striking electric guitar that caters to a wide range of musical genres, from rock to metal. Known for its exceptional playability and innovative design, this instrument stands out not only in appearance but also in performance.

At the heart of the JP-24BPNSU is its solid body, which is crafted from high-quality basswood. This lightweight tonewood contributes to the guitar's resonant sound while ensuring comfort during extended playing sessions. With a sleek, contoured design, the body allows for easy reach across the fretboard, making it an ideal choice for players who favor speed and agility.

The guitar features a unique bolt-on maple neck that offers stability and enhances sustain, paired with a rosewood fingerboard for a warm tonal quality. With 24 jumbo frets, the JP-24BPNSU provides ample space for intricate licks and solos, catering to both beginners and advanced players. Its 25.5-inch scale length contributes to a tight, focused sound that is perfect for aggressive playing styles.

One of the standout features of this guitar is its high-output Jackson humbucking pickups. These pickups deliver powerful tones with excellent clarity, making them suitable for various musical styles. They are designed to handle high levels of gain, allowing performers to achieve thick, saturated sounds without muddiness. The JP-24BPNSU also features a versatile three-way pickup selector switch, providing players with options to explore different tonal palettes effortlessly.

In terms of hardware, the guitar comes equipped with a high-quality licensed Floyd Rose tremolo system. This allows for dramatic pitch bending and dive-bombing effects while maintaining tuning stability, which is essential for many modern guitar techniques. The guitar's reliable tuning machines further enhance its performance, ensuring that your instrument stays in tune even after intense playing sessions.

Aesthetically, the Jackson JP-24BPNSU is designed to catch the eye. It often boasts a bold finish combined with striking body contours, making it a visually appealing choice for performers. The cutting-edge craftsmanship and attention to detail not only provide an attractive look but also ensure durability and longevity.

Overall, the Jackson JP-24BPNSU is an ideal electric guitar for musicians seeking a blend of style, tone, and performance. With its range of features and technologies, it is well-suited for both studio work and live performances. Whether you are a beginner or a seasoned player, the JP-24BPNSU offers an exceptional playing experience that is sure to inspire creativity and enhance your musical journey.
Top Page Image Contents