Keating Of Chicago MG-4, MG-2 service manual III Operating, IV Maintenance

Page 7

WARNING

PROPANE GAS MAY EVENTUALLY LOSE ITS ODOR AND PRECAUTIONS SHOULD BE TAKEN TO ASSURE THAT IT IS NOT PRESENT EVEN THOUGH YOU DO NOT DETECT AN ODOR. IF THERE IS ANY DOUBT, YOU SHOULD CALL YOUR LOCAL PROPANE GAS SUPPLIER FOR ASSISTANCE.

III OPERATING

LIGHTING

Keating hot plates are designed to provide maximum efficiency and deliver high quality food products. Follow lighting procedure below.

WARNING

OPERATION OF THIS HOT PLATE SHOULD BE LIMITED TO PERSONNEL WHO HAVE BEEN THOROUGHLY TRAINED IN OPERATING PROCEDURES.

1.Open the manual gas valve.

2.For hot plates with constant pilots, light the constant pilot (located between the front and rear burners) with a match. For hot plates with spark ignitors, push in the red knob and rotate it fully counterclockwise unit the burner ignites.

CAUTION: For hot plates with spark ignitors, rotating the red knob without holding it in may damage the gas valve (infinite switch).

CAUTION: If the pilot or burner fails to stay lit, wait five minutes before attempting to relight to allow any accumulated gas to escape.

3.For hot plates with constant pilots, rotate the red knob counterclockwise to the desired setting. For hot plates with spark ignitors, rotate the red knob clockwise to the desired setting after the burner ignites.

NOTE: The left knob operates the back burner and the right knob operates the front burner.

SHUTDOWN

1. Rotate the red knob fully clockwise for each burner.

CLEANING

When cleaning your hot plate, use Keating Klenzer, the finest dry stainless steel polish available, to restore your hot plate’s exterior to it original luster. Keating Klenzer is USDA approved.

CAUTION: For hot plates with optional spark ignitors, disconnect the electrical power source before doing any cleaning.

IV MAINTENANCE

WARRANTY REPAIRS

Keating’s warranty begins with the date of installation. In the event that your hot plate, under warranty, needs repairs other than routine maintenance or cleaning, you are requested to contact Keating of Chicago (at 1-800- KEATING) before calling a local service company.

PREVENTIVE MAINTENANCE

Preventive maintenance should be done in daily, weekly, monthly and yearly intervals as necessary. Following preventive maintenance procedures will help keep your hot plate working efficiently. Proper care and servicing will lead to years of quality performance.

PREVENTIVE MAINTENANCE CHART

TIME

OPERATOR/OWNER

SECTION

QUALIFIED SERVICE

FRAME

 

 

PERSONNEL ONLY

 

 

 

 

At Least

￿ Check controls

III

 

Daily

￿ Drain and clean drip

 

 

 

pan.

III

 

 

 

 

 

At Least

 

 

 

Weekly

￿ Clean hot plate.

III

 

 

 

 

 

At Least

 

V

￿ Disassemble hot

Yearly*

 

 

plate to clean

 

 

 

burners and orifices.

 

 

 

 

 

*High production facilities should be checked more often.

4

Page 6 Page 8
Image 7
Page 6 Page 8
Contents GAS HOT Plate Service Manual Table of Contents Post this Label in a Prominent Location on Your Unit Introduction What to do if equipment arrives damaged II InstallationInstallation Damage During ShipmentElectrical Connection GAS Leak TestingPositioning Restraining DevicesIII Operating IV MaintenanceOrdering Parts Service DiagnosisVII Parts Lists Problem Probable Cause SolutionPart GAS HOT Plate Parts ListDescription MG-2 MG-4 Number HOT Plate Assembly MG SI Wiring and Ladder Diagrams Viii Wiring DiagramsWarranty Serving Those Who Serve The Very Best

MG-4, MG-2 specifications

The Keating Of Chicago MG-2 and MG-4 are standout models in the realm of high-performance ultra-light aircraft, showcasing cutting-edge technology and engineering. These aircraft are particularly noted for their innovative design and impressive performance, catering to both recreational pilots and aviation enthusiasts.

The MG-2 is an impressive two-seat aircraft, designed with a focus on agility and efficiency. It features a sleek composite airframe, which not only reduces weight but also enhances durability. One of its main characteristics is its low stall speed, allowing for safe landings and takeoffs in various conditions. Equipped with a state-of-the-art engine, the MG-2 offers remarkable fuel efficiency while delivering a responsive flying experience. The cockpit is ergonomically designed, providing an intuitive interface for the pilot, complete with advanced avionics that ensure navigation and communication remain seamless during flight.

On the other hand, the MG-4 brings a more spacious, four-seat configuration to the lineup, making it a versatile option for families or group outings. This model retains the premium build quality of the MG-2 while expanding on its capacity and range. Key features include a higher payload capacity and increased fuel tank volume, enabling longer journeys without compromising comfort. The MG-4's cabin is designed for passenger comfort, with ample legroom and modern amenities that enhance the flying experience.

Both aircraft utilize advanced materials, including carbon fiber composites, to optimize structural integrity while minimizing weight. This focus on materials translates into superior performance, with both models offering enhanced speed, climb rates, and overall handling.

One of the standout technologies incorporated in both the MG-2 and MG-4 is the fly-by-wire control system, which enhances maneuverability and simplifies handling, making these aircraft accessible to both novice and experienced pilots alike. This modern system improves responsiveness and provides critical data feedback in real-time, ensuring that pilots maintain optimal control.

In summary, the Keating Of Chicago MG-2 and MG-4 represent the pinnacle of modern ultralight aviation technology, with their strong emphasis on safety, efficiency, and passenger comfort. Whether for training, recreation, or cross-country flights, these models are designed to deliver an unmatched flying experience, further solidifying their place in the aviation landscape.
Top Page Image Contents