Keating Of Chicago 2006 Service Diagnosis, Gas Pressure, Air Flow, Required Test Thermostat

Page 12

Short Cycle: The thermostat will cycle rapidly while the fryer is in the idle mode; the temperature will be erratic.

Thermostat Bulb Positioning 18" & up Fryer Gas

SERVICE

ALL HI-LIMIT CONTROLS ARE PRESET AT THE FACTORY FOR A SPECIFIC TEMPERATURE. DO NOT ATTEMPT TO CHANGE THE SETTING OF THE HI-LIMIT. IF THE HI-LIMIT FAILS TO SHUT OFF BETWEEN 425°F AND 450°F DURING TESTING, IT MUST BE REPLACED.

FLAME ADJUSTMENT

A. Gas Pressure

1.At gas valve, remove adjustment port cover, rotate adjustment screw with screwdriver and replace port cover.

2.To check the gas pressure (3" WC for natural gas or 10" WC for Propane at the manifold), use an allen wrench to remove the gas pressure test port, located in the center of the manifold.

3.Line pressure (incoming pressure) is critical for proper ignition of the IFM. Incoming pressure must

be : Natural - 7” W.C. Propane - 11” W.C.

B. Air Flow

1.To determine the proper gas/air mixture, look into the viewing window for each burner, located just to the left of each burner air hose where the hose is connected to the burner assembly. (See figure below).

•bright red/orange with proper mixture – orange “glow” around burner tube

•too much gas – orange “haze” around burner tube (showing incomplete combustion)

•too little gas – blue at front of burner, or totally blue

Remove the cover by loosening the screws to gain access to the burner viewing windows (14” Model Shown).

REQUIRED TEST THERMOSTAT

Multimeter (for testing continuity)

CHECKING CONTINUITY WITH THE MULTIMETER

1.Rotate the thermostat shaft until an audible click is heard.

2.Rotate the thermostat shaft left and right ten times causing the switch to click on and off ten times, while using the Multimeter to verify continuity.

3.If the switch does not show continuity during all ten trials, replace the thermostat.

Disassembling the thermostat will void the thermostat warranty.

1.Set compression ring onto capillary end of bulb finger tight, 1/2” from end of capillary.

2.Insert new thermostat bulb through control panel back.

3.Apply oil resistant flexible sealant ontocompression fitting thread before installing fitting into fryer vessel.

4.Position bent portion of bulb against far right heat transfer tube and install compression fitting snugly into fryer vessel.

5.Adjust bulb so at least 2” of bent portion of it is next to heat transfer tube and tighten compression nut onto compression fitting for fryer 18 & up. The end of thermostat bulb should touch the burner tube for 14" fryers.

6.Refill fryer with oil to “fill level line”.

7.Start fryer, preheat and calibrate with thermometer.

SERVICE DIAGNOSIS

A properly adjusted Keating Incredible Frying Machine® (IFM), with no load, will cycle “On” approximately every 2 1/2 to 3 minutes. Each cycle will last 15 to 25 seconds, ensuring that the temperature setting is held within a narrow band.

•Every Keating Incredible Frying Machine® (IFM) has a number of safety controls to ensure safe operation and guard against component failure.

10

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Contents Series 2006 Fryer ManualRead and Save this Manual for Future Reference Post this Label in a Prominent Location on Your Unit Introduction Clearances Installation InstallationDamage During Shipment LevelingGAS Leak Testing Electrical ConnectionOperating GAS Pressure AT ManifoldMaximum Incoming GAS Pressure See FigureDigital Timer Resetting to Minutes Seconds Step CookingShut Down Digital Timer Programming Pause FeatureCanceling a Cycle Cleaning and BOIL-OUTClose drain valve Maintenance Warranty RepairsPreventive Maintenance Qualified Service PERService Service DiagnosisGas Pressure Air FlowCommon Problems Probable Cause Solutions Follow Sequentially SELF-HELP GuideTroubleshooting Chart Problem Probable Cause SolutionBreaker tripped Problem Probable Cause Solution Parts List Drain Valve Pull Rod AssemblyOrdering Parts Corresponds with parts list on Incredible Frying Machine GAS Fryer Rear Drain Model030862 Blower 053726 See pages 23-25 for Control Panel Parts List Incredible Frying Machine GAS Fryer Front Drain ModelThermostat Burner Assembly see Insulation High LimitDescription QTY Part Number IFM Control Panel Parts List with Timers Model IFM Control Panel Parts List Model 2006 CPU Located on Rear Drain Units only Description QTY Part Number 166 16 Burner Replacement KIT Description QTY Wiring Diagrams IFM 120V Connection Diagram no TIMERS, Front Drain Model Control Panel Insert Control Panel Back IFM Model 2006 Front Drain Without Lighted Rocker Switch IFM Model 2006 with Safe and Easy Filter IFM Model 2006 CPU Basket Lift Front Drain Page Page Page Page Effective 5/2006 Effective 5/2006 Warranty Service Information Keating Limited Warranty Card

2006 specifications

Keating of Chicago 2006 is a significant entry in the world of high-performance sports cars, designed to offer an exhilarating driving experience while emphasizing speed, technology, and innovative engineering. Developed by Keating Sports Cars, a British automotive manufacturer known for its dedication to performance and craftsmanship, the 2006 model showcases the brand’s ethos of creating lightweight and powerful vehicles.

One of the standout features of the Keating of Chicago is its striking design, which blends aerodynamic efficiency with aesthetic appeal. The car boasts a low profile and sleek lines that not only catch the eye but also facilitate optimal airflow, reducing drag during high-speed maneuvers. Available in various striking colors, the exterior encapsulates the essence of a true sports car, conveying both aggression and elegance.

At the heart of the Keating of Chicago lies a formidable powertrain. The car is typically equipped with an advanced V8 engine, which can produce over 500 horsepower, ensuring thrilling acceleration and top speeds. This engine is paired with an efficient transmission system, providing seamless gear shifts and enhancing driving pleasure. The lightweight chassis contributes to the car’s impressive power-to-weight ratio, allowing it to leap from 0 to 60 mph in just a few seconds.

In terms of technology, the Keating of Chicago is well-equipped with modern conveniences and enhancements aimed at improving both performance and driver experience. Features such as advanced suspension systems, performance brakes, and traction control systems ensure that drivers experience unparalleled handling and stability on various terrains. The integration of digital dashboards provides essential information at a glance, allowing drivers to monitor vital metrics while maintaining focus on the road ahead.

The interior of the Keating of Chicago is designed with driver comfort in mind, offering a minimalist yet functional layout that prioritizes ergonomics and user experience. High-quality materials and bespoke options allow for customization, ensuring that each car is as unique as its owner. With comfortable seating and an intuitive control system, the driving experience is both engaging and enjoyable.

Overall, Keating of Chicago 2006 serves as a testament to the manufacturer's commitment to performance, technology, and style. With its potent engine, aerodynamic design, and cutting-edge features, it continues to be a desirable choice for enthusiast drivers seeking a unique blend of performance and luxury in the world of sports cars.
Top Page Image Contents