GE JDP39 owner manual Type of margarine will affect baking performance, Consumer Support

Page 14

Using the Sabbath Feature.

(Designed for use on the Jewish Sabbath and Holidays)

How to Exit the Sabbath Feature

Touch the CLEAR/OFF pad.

If the oven is cooking, wait for a random delay period of approximately 30 seconds to 1 minute, until only ⊃ is in the display.

Touch and hold both the BAKE and BROIL HI/LO pads, at the same time, until the display shows SF.

Tap the CLOCK pad until ON or OFF appears in the display. ON indicates that the oven will automatically turn off after 12 hours. OFF indicates that the oven will not automatically turn off. See

the Special Features section for an explanation of the 12 Hour Shut-Off feature.

Touch the START/ON pad.

NOTE: If a power outage occurred while the oven was in Sabbath, the oven will automatically turn off and stay off even when the power returns. The oven control must be reset.

Adjust the oven thermostat—Do it yourself!

You may find that your new oven cooks differently than the one it replaced. Use your new oven for a few weeks to become more familiar with it. If you still think your new oven is too hot or too cold, you can adjust the thermostat yourself.

Do not use thermometers, such as those found in grocery stores, to check the temperature setting of your oven. These thermometers may vary 20–40 degrees.

NOTE: This adjustment will not affect the broiling or the self-cleaning temperatures. The adjustment will be retained in memory after a power failure.

Troubleshooting Tips Care and Cleaning Operating Instructions Safety Instructions

To Adjust the Thermostat

Touch the BAKE and BROIL HI/LO pads at the same time for 2 seconds until the display shows SF.

Touch the BAKE pad. A two-digit number shows in the display.

The oven temperature can be adjusted up to (+) 35°F hotter or (–) 35°F cooler. Touch the + pad to increase the temperature in 1-degree increments.

Touch the pad to decrease the temperature in 1-degree increments.

When you have made the adjustment, touch the START/ON pad to go back to the time of day display. Use your oven as you would normally.

NOTE: This adjustment will not affect the broiling or self-cleaning temperatures. It will be retained in memory after a power failure.

Consumer Support

The type of margarine will affect baking performance!

Most recipes for baking have been developed using high-fat products such as butter or margarine (80% fat). If you decrease the fat, the recipe may not give the same results as with a higher-fat product.

Recipe failure can result if cakes, pies, pastries, cookies or candies are made with low-fat spreads. The lower the fat content of a spread product, the more noticeable these differences become.

Federal standards require products labeled “margarine” to contain at least 80% fat by weight. Low-fat spreads, on the other hand, contain less fat and more water. The high moisture content of these spreads affects the texture and flavor of baked goods. For best results with your old favorite recipes, use margarine, butter or stick spreads containing at least 70% vegetable oil.

14

Image 14
Contents Safety Instructions Operating Instructions Write the model and serial numbers here Model # Serial #Consumer Support Troubleshooting All ranges can tip and injury could resultTips Consumer Operating Instructions Care and Cleaning TroubleshootingSupport Troubleshooting Tips Care and Cleaning ConsumerTips Consumer Support Using the surface unitsSafety Functions must be reset Using the oven controlsConsumer Support Troubleshooting Tips Care and Cleaning Been a power outage. Reset the clockControl Lockout Instructions Care and CleaningTroubleshooting Tips Consumer Power Outage To lock/unlock the controlsTroubleshooting Using the ovenTips Care and Cleaning InstructionsBroiling Guide How to Set the Oven for BroilingInstructions Operating Broiling GuideTroubleshooting Tips Care Using the clock and timerCleaning How to Set an Immediate Start and Automatic Stop Safety InstructionsTroubleshooting Tips Consumer Support How to Set a Delayed Start and Automatic StopHour Shut-Off Special features of your oven controlSafety Instructions How to Set for Regular Baking/Roasting Using the Sabbath FeatureSafety Instructions Designed for use on the Jewish Sabbath and HolidaysType of margarine will affect baking performance To Adjust the ThermostatHow to Exit the Sabbath Feature Consumer SupportBefore a Clean Cycle Using the self-cleaning ovenCleaning Troubleshooting Tips Consumer Support How to Set the Oven for CleaningHow to Delay the Start of Cleaning Consumer Support Troubleshooting TipsAfter a Clean Cycle Vinegar and water mixtureControl Knobs Care and cleaning of the rangeHow to Remove Packaging Tape Control PanelConsumer Support Troubleshooting Tips Care and Cleaning Operating InstructionsInstructions Operating Instructions Care Cleaning Troubleshooting Tips ConsumerCleaning the Oven Door Lift-Off Oven DoorTo remove the cover Oven Light ReplacementBroiler Pan and Grid To replace the coverInstructions Operating Instructions Care and CleaningTroubleshooting Tips Before you call for service… Problem Possible Causes What To DoUnlock Oven not clean after See the Using the self-cleaning oven sectionDuring a clean cycle Clean cycleOr letter flash Power outageA number DisplayWe’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Safety Instructions Care and CleaningOperating Instructions Safety Instructions Accessories Looking For Something More?Instructions Care GE Electric Range WarrantyCleaning Troubleshooting Tips Consumer Support GE Will ProvideConsumer Support GE Appliances Website Schedule ServiceParts and Accessories Real Life Design Studio
Related manuals
Manual 16 pages 27.5 Kb

JDP39 specifications

The GE JDP39 and JDS28 series, including model 131-10595-2 1-07 JR, represent significant advancements in the realm of electronic instrumentation and components, essential for various industrial applications. These models are part of General Electric's ongoing commitment to innovation and reliability in technology.

One of the standout features of the JDP39 and JDS28 models is their robustness in harsh environments. Designed with durability in mind, these devices can withstand extreme temperatures, humidity, and vibration, making them ideal for use in sectors such as aerospace, manufacturing, and power generation. The materials used in their construction ensure longevity and reliable performance under stress.

In terms of technology, the GE JDP39 model employs advanced signal processing capabilities. This enables high accuracy and rapid response times in measurement applications. The devices incorporate state-of-the-art sensors that provide precise data, which is crucial for monitoring and controlling various industrial processes. This level of precision is particularly beneficial in applications where safety and efficiency are paramount.

The JDS28 series is known for its user-friendly interface and ease of integration with existing systems. Designed with operators in mind, these devices feature intuitive controls and clear displays that ensure quick adaptation and minimal training period for users. Furthermore, they support various communication protocols, facilitating seamless integration into modern automated systems.

Power efficiency is another significant characteristic of the GE JDP39 and JDS28 models. With a focus on reducing energy consumption without compromising performance, these devices utilize advanced power management technologies. This not only lowers operational costs but also aligns with global initiatives aimed at promoting energy sustainability.

Additionally, GE has incorporated advanced diagnostic features into these models. Users can access real-time data and alerts regarding the operational status, enabling proactive maintenance and reducing downtime. This predictive capability is vital for organizations seeking to enhance their operational efficiency and minimize unexpected failures.

In conclusion, the GE JDP39, JDS28, and the 131-10595-2 1-07 JR model embody the intersection of durability, advanced technology, and user-friendly design. Their features make them an indispensable choice for industries requiring reliable instrumentation that can perform consistently under challenging conditions. As industries continue to evolve and embrace automation, these devices stand out as essential tools for achieving operational excellence.