GE JDP39 owner manual Consumer Support Troubleshooting, All ranges can tip and injury could result

Page 2

Tips Care and Cleaning Operating Instructions Safety Instructions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of fire, electric shock, or to prevent property damage, personal injury, or loss of life.

WARNING ANTI-TIP DEVICE

All ranges can tip and injury could result.

To prevent accidental tipping of the range, secure the attached Anti-Tip bracket, under the rear countertop.

If the Anti-Tip device supplied with the range does not fit this application, use the universal Anti-Tip device WB2X7909.

To check if the device is installed and engaged properly, lower the oven door and gently apply medium force at the handle end until movement of the range is detected. Continue pressing until the anti-tip bracket is engaged and movement stops. A small amount of movement is acceptable at the back of the range top but it should be stable and not tip once the anti-tip bracket is engaged.

If you pull the range out from the wall for any reason, make sure the device is properly engaged when you push the range back against the wall. If it is not, there is a possible risk of the range tipping over and causing injury if you or a child stand, sit or lean on an open door.

Please refer to the Anti-Tip device information shipped with the device and in this manual. Failure to take this precaution could result in tipping of the range and injury.

IMPORTANT SAFETY NOTICE

The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of substances known to the state to cause cancer, birth defects or other reproductive harm, and requires businesses to warn customers of potential exposure to such substances.

The fiberglass insulation in self-clean ovens gives off a very small amount of carbon monoxide during the cleaning cycle. Exposure can be minimized by venting with an open window or using a ventilation fan or hood.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

Consumer Support Troubleshooting

Use this appliance only for its intended purpose as described in this Owner’s Manual.

Be sure your appliance is properly installed and grounded by a qualified installer in accordance with the provided installation instructions.

Have the installer show you the location

of the circuit breaker or fuse. Mark it for easy reference.

Do not attempt to repair or replace any part of your range unless it is specifically recommended in this manual. All other servicing should be referred to a qualified technician.

Before performing any service, disconnect the range power supply at the household distribution panel by removing the fuse or switching off the circuit breaker.

2

Do not leave children alone—children should not be left alone or unattended in an area where an appliance is in use. They should never be allowed to sit or stand on any part of the appliance.

Do not allow anyone to climb, stand or hang on the door or cooktop. They could damage the range and even tip it over, causing severe personal injury.

Large scratches or impacts to glass doors can lead to broken or shattered glass.

Do not store flammable materials in an oven or near the cooktop.

CAUTION: Items of interest to children should not be stored in cabinets above a range or on the backsplash of a range—children climbing on the range to reach items could be seriously injured.

Image 2
Contents Safety Instructions Operating Instructions Write the model and serial numbers here Model # Serial #Consumer Support Troubleshooting All ranges can tip and injury could resultTips Consumer Operating Instructions Care and Cleaning TroubleshootingSupport Troubleshooting Tips Care and Cleaning ConsumerTips Consumer Support Using the surface unitsSafety Functions must be reset Using the oven controlsConsumer Support Troubleshooting Tips Care and Cleaning Been a power outage. Reset the clockControl Lockout Instructions Care and CleaningTroubleshooting Tips Consumer Power Outage To lock/unlock the controlsTroubleshooting Using the ovenTips Care and Cleaning InstructionsBroiling Guide How to Set the Oven for BroilingInstructions Operating Broiling GuideTroubleshooting Tips Care Using the clock and timerCleaning How to Set an Immediate Start and Automatic Stop Safety InstructionsTroubleshooting Tips Consumer Support How to Set a Delayed Start and Automatic StopHour Shut-Off Special features of your oven controlSafety Instructions How to Set for Regular Baking/Roasting Using the Sabbath FeatureSafety Instructions Designed for use on the Jewish Sabbath and HolidaysType of margarine will affect baking performance To Adjust the ThermostatHow to Exit the Sabbath Feature Consumer SupportBefore a Clean Cycle Using the self-cleaning ovenCleaning Troubleshooting Tips Consumer Support How to Set the Oven for CleaningHow to Delay the Start of Cleaning Consumer Support Troubleshooting TipsAfter a Clean Cycle Vinegar and water mixtureControl Knobs Care and cleaning of the rangeHow to Remove Packaging Tape Control PanelConsumer Support Troubleshooting Tips Care and Cleaning Operating InstructionsInstructions Operating Instructions Care Cleaning Troubleshooting Tips ConsumerCleaning the Oven Door Lift-Off Oven DoorTo remove the cover Oven Light ReplacementBroiler Pan and Grid To replace the coverInstructions Operating Instructions Care and CleaningTroubleshooting Tips Before you call for service… Problem Possible Causes What To DoUnlock Oven not clean after See the Using the self-cleaning oven sectionDuring a clean cycle Clean cycleOr letter flash Power outageA number DisplayWe’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Safety Instructions Care and CleaningOperating Instructions Safety Instructions Accessories Looking For Something More?Instructions Care GE Electric Range WarrantyCleaning Troubleshooting Tips Consumer Support GE Will ProvideConsumer Support GE Appliances Website Schedule ServiceParts and Accessories Real Life Design Studio
Related manuals
Manual 16 pages 27.5 Kb

JDP39 specifications

The GE JDP39 and JDS28 series, including model 131-10595-2 1-07 JR, represent significant advancements in the realm of electronic instrumentation and components, essential for various industrial applications. These models are part of General Electric's ongoing commitment to innovation and reliability in technology.

One of the standout features of the JDP39 and JDS28 models is their robustness in harsh environments. Designed with durability in mind, these devices can withstand extreme temperatures, humidity, and vibration, making them ideal for use in sectors such as aerospace, manufacturing, and power generation. The materials used in their construction ensure longevity and reliable performance under stress.

In terms of technology, the GE JDP39 model employs advanced signal processing capabilities. This enables high accuracy and rapid response times in measurement applications. The devices incorporate state-of-the-art sensors that provide precise data, which is crucial for monitoring and controlling various industrial processes. This level of precision is particularly beneficial in applications where safety and efficiency are paramount.

The JDS28 series is known for its user-friendly interface and ease of integration with existing systems. Designed with operators in mind, these devices feature intuitive controls and clear displays that ensure quick adaptation and minimal training period for users. Furthermore, they support various communication protocols, facilitating seamless integration into modern automated systems.

Power efficiency is another significant characteristic of the GE JDP39 and JDS28 models. With a focus on reducing energy consumption without compromising performance, these devices utilize advanced power management technologies. This not only lowers operational costs but also aligns with global initiatives aimed at promoting energy sustainability.

Additionally, GE has incorporated advanced diagnostic features into these models. Users can access real-time data and alerts regarding the operational status, enabling proactive maintenance and reducing downtime. This predictive capability is vital for organizations seeking to enhance their operational efficiency and minimize unexpected failures.

In conclusion, the GE JDP39, JDS28, and the 131-10595-2 1-07 JR model embody the intersection of durability, advanced technology, and user-friendly design. Their features make them an indispensable choice for industries requiring reliable instrumentation that can perform consistently under challenging conditions. As industries continue to evolve and embrace automation, these devices stand out as essential tools for achieving operational excellence.