Damper Sizing Information
Dampers larger than maximum single section size are supplied as a factory assembly of two or more sections of equal size.
The following figures show damper sections and assemblies that have been qualified for operation with a single actuator. Larger sizes can be accommodated using multiples of these assemblies.
Double Section
Single Section
50 in. (1270mm)
50 in. (1270mm)
32 in. (813mm) 64 in. (1626mm)
32 in. (813mm)
Transitioned Damper Dimensions
When a fire/smoke damper is being used in conjunction with round or oval ductwork, the
D*+ 2 in. ( |
|
|
|
|
|
|
|
| |
51mm) +T | s |
| W*+ | 2 in. (51mm)+T |
| ||||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| s | |
|
|
|
| W*+ 2 | in. (51mm)+T | s |
|
| |
|
|
|
|
|
|
|
|
|
|
D* + 2 in. (51mm)+T |
| s |
| H*+ 2 in. (51mm)+T | s | ||
|
|
|
| ||||
|
|
|
| 21/8 in. |
|
|
|
|
|
|
| (54mm) |
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
16 in. (406mm) | D* | 16 in. (406mm) |
Min. |
| Min. |
TYPE R
|
|
| H* + 2 in. (51mm)+T |
| s |
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |||||
|
|
| H* |
|
|
|
|
|
|
| H* |
| |
1 |
|
|
|
|
| 21/8 in. |
| ||||||
|
|
|
|
|
| ||||||||
|
| 2 /8 in. |
|
|
|
|
|
|
|
|
|
|
|
| (54mm) |
|
|
|
|
|
| (54mm) | |||||
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| W* |
|
|
|
|
|
|
|
| * These dimensions are furnished | |||
|
|
| 16 in. (406mm) |
| W* |
| |||||||
|
|
|
|
|
| ||||||||
|
|
|
|
|
| approximately 1/4 in. (6mm) undersize, | |||||||
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
| |||||||
|
|
|
|
|
| Min. |
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
| except round and oval dimensions | ||
TYPE O |
|
|
|
|
| TYPE C | which are approximately 1/8 in. (3mm) | ||||||
|
|
|
|
| undersize. | ||||||||
Ts = (2)(Sleeve Thickness)
Specifications
Smoke Dampers meeting the following specifications shall be furnished and installed where shown on plans and/or as described in schedules. Dampers shall meet the require- ments of NFPA 92A, 92B, 101, and 105 and further shall be tested, rated and labeled in accordance with the latest edition of UL Standard 555S. Smoke dampers shall be of low leakage design qualified to UL 555S Leakage Class II.
Each damper /actuator combination shall have a UL555S elevated temperature rating of 250°F (121º C) minimum and shall be rated to operate at maximum design air flow at its installed location. Each damper shall be supplied with an appropriate actuator installed by the damper manufacturer at the time of damper fabrication. Damper actuator shall be (specifier select one of the following) electric type for 24 Volt operation.
Damper blades shall be of the double skin airfoil type and
shall have an equivalent metal thickness of 14 ga. (2mm) Damper frame shall be galvanized steel formed into a struc- tural hat channel shape with reinforced corners. Bearings shall be sintered bronze sleeve type rotating in extruded holes in the damper frame. Blade edge seals shall be sili- cone rubber designed to inflate and provide a tighter seal against leakage as pressure on either side of the damper increases. Jamb seals shall be stainless steel compression type with silicone rubber backing. Blades shall be complete- ly symmetrical relative to their axle pivot point, presenting identical resistance to airflow in either direction or pressure on either side of the damper.
Damper must be rated for mounting vertically (with blades running horizontal) or horizontally and be UL 555S rated for leakage and airflow in either direction through the damper.
The basis of design is Greenheck Model
Copyright ©2007 Greenheck Fan Corporation