Greenheck Fan 470658 MSX manual Water Wizard Improper Water Supply, Adjust the Manual Supply Valve

Page 32

Troubleshooting

Water Wizard™ — Improper Water Supply

note

If the water supply is too low, the media will continuously appear dry.

note

If the water supply is too high, the media will be saturated and excessive water will be draining from the sump tank.

note

Some water drainage is desired to keep the media flushed, but it should be minimized to utilize the Water Wizard™.

1. Adjust the Manual Supply Valve

Adjust the manual supply valve (refer to Start-Up, Water Wizard™). If the recommended water pressure does not provide enough water, increase the pressure until the desired water supply is achieved. If the recommended water pressure provides too much water, decrease the water pressure until the desired water supply is achieved.

caution

Only proceed to Steps 2 and 3 if Step 1 does not correct the problem.

2. Enter Program Mode

Press and hold

 

the Enter key for

 

three seconds to enter

 

Program Mode. The

 

display will read “Pro”

 

when Program Mode is

Program Display

active.

3. Adjust the On Time Factor

While in the Program Menu, use the Up and Down keys to navigate through the menu options until “ont” is displayed.

With “ont” displayed, press the Enter key to access the setting.

With the setting displayed, use the Up and Down keys to adjust the setting as needed.

Increase the factor to increase the water supply or decrease the factor to decrease the water supply.

Press the Enter key to save the new On Time Factor and return to the Program Menu.

On Time Factor Display

note

Changing the On Time Factor by (1) will change the water supply by approximately 3%.

important

The enter key must be pressed to save the new On Time Factor.

4. Exit Program Mode

After 15 seconds of idle time the controller will automatically exit Program Mode

32

Model MSX Make-Up Air

®

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Installation, Operation and Maintenance Manual General Safety InformationInspection and Maintenance during Storage ReceivingUnpacking HandlingInstallation of Indoor Unit Table of ContentsClearance to Combustibles / Service Clearances Installation Arrangement DB / HZ / UB Installation of Roof Mounted Unit Arrangement DBC Install Curb/Equipment SupportsInstall Combination Extension Install Exhaust FanInstall Supply Unit Installation of Evaporative Cooling Module optional Locate Equipment SupportsSecure Cooling Module to Unit Set Evaporative Cooling ModuleInstallation of Electrical Wiring Installation of Electric Heater optional Sizing of Supply ConductorsInstallation Evaporative Cooler Piping optional Install the Water Supply LineInstall the Drain Line Check/Adjust Water LevelInstall the Drain Line Installation of Water WizardTM optional Install Normally Closed Supply Line/ SolenoidInstall Normally Open Drain Line/ Solenoid Wire the SolenoidsInstallation of Direct Expansion DX Coil Piping optional Installation of Chilled Water Coil Piping optional Verify Coil Hand DesignationCheck the Coil for Leaks Connect the Supply and Return LinesInstallation of Building Pressure Control optional Mount Pressure TapRun Pressure Tap Lines Set the Building PressureStart-Up Blower Air Volume Measurement & Check Set-Up Optional ComponentsAirflow Interlock Set the Unit’s Operating TemperatureStart-Up Electric Heater optional Start-Up Evaporative Cooling Recirculating optional Start-Up Water Wizard optional Adjust the Freeze Temperature Building Pressure Control Variable Volume OperationCheck Operation VAV Units optional Building Pressure Control a Operation Electrical Exhaust Fan Contact S1 Closed optionalSupply Fan Contact S2 Closed Electric Heat Contact S4 Closed optionalOperation - Water Wizard optional Troubleshooting Blower Does Not OperateMotor Overamps Insufficient Airflow Too Much AirflowExcessive Noise or Vibration Electric Heater Does Not Operate optional Supply fan must be on for heater to operateEvaporative Cooler does not Operate Recirculating pump Water Blows through Evaporative CoolerWater Wizard Improper Water Supply Adjust the Manual Supply ValveAdjust the On Time Factor Maintenance Routine Belt DrivesSnow Accumulation MotorsEvaporative Coolers BearingsFilters Cooling Coils Chilled Water CoilsMaintenance Fall Winterizing Chilled Water CoilsBlowing-Out Coils Flushing CoilsTypical Control Center Layout Dirty Filter SwitchReference Start-Up Evaporative Cooler optional refer Start-Up ChecklistStart-Up Checklist Maintenance Log Warranty

470658 MSX specifications

The Greenheck Fan 470658 MSX is a premium performance ventilation solution designed to meet the needs of various commercial and industrial applications. Known for its robustness and efficient air movement capabilities, the MSX series is highly regarded in the industry for its innovative technologies and user-friendly features.

One of the standout features of the Greenheck Fan 470658 MSX is its advanced motor technology. It is equipped with an energy-efficient direct drive motor, which minimizes energy consumption while delivering high airflow rates. The motor's design allows for quieter operation, making it ideal for environments where noise reduction is crucial.

The aerodynamic design of the fan blades is another hallmark of the Greenheck MSX. The blades are engineered to enhance performance by maximizing airflow while reducing turbulence. This design optimization results in increased efficiency and lower operational costs over time. Furthermore, the fan is capable of handling a wide range of air volumes, making it versatile for various installation requirements.

Durability is a key characteristic of the Greenheck Fan 470658 MSX. Constructed from high-quality materials, it can withstand harsh environmental conditions, including exposure to moisture and corrosive elements. The fan housing is designed to be robust, ensuring long-lasting performance and minimal maintenance needs.

In addition to its physical attributes, the MSX series comes equipped with smart technology features. The fan can be integrated with building management systems for real-time monitoring and control, helping facility managers optimize energy usage and maintain indoor air quality. The inclusion of variable speed controls further enhances adaptability, allowing users to adjust fan speed according to specific ventilation needs.

Safety features are also a priority with the Greenheck Fan 470658 MSX. The unit is designed with built-in protections against overheating and overcurrent, ensuring reliable operation under demanding conditions. Additionally, the fan meets rigorous safety standards and certifications, instilling confidence in its performance.

With its combination of efficiency, durability, and innovative features, the Greenheck Fan 470658 MSX is a top choice for those seeking reliable ventilation solutions. Its ability to deliver consistent airflow while minimizing energy consumption sets it apart in the competitive market of industrial fans, making it a valuable investment for businesses looking to enhance their air management systems.
Top Page Image Contents