Samsung FER300SXPKG Removing heavy, burned-on residue, Removing metal marks and scratches

Page 36

Removing heavy, burned-on residue

1. Allow the cooktop to cool.

2. Use the single-edge razor-blade scraper at approximately a 45° angle against the glass surface and scrape the soil. It will be necessary to apply pressure in order to remove the residue.

3. After scraping with the razor scraper, spread a few drops of ceramic cooktop cleaner on the entire burned residue area. Use the cleaning pad to remove any remaining residue. (Do not scrape the seal.)

4. For additional protection, after all residue has been removed, polish the entire surface with the cooktop cleaner and a paper towel.

Removing metal marks and scratches

1.Be careful not to slide pots and pans across your cooktop. It will leave marks on the cooktop surface. You can remove these marks by applying ceramic cooktop cleaner.

2.If pots with a thin overlay of aluminum or copper are allowed to boil dry, the overlay may leave black discoloration on the cooktop. You should remove this discoloration immediately or it may become permanent.

Carefully check the bottoms of pans for roughness that may scratch the cooktop.

Cleaning the cooktop seal

To clean the seal around the edges of the glass, lay a wet cloth on it for a few minutes, then wipe clean with a nonabrasive cleaner.

Potential for permanent damage to the glass surface

•Sugary spillovers (such as jellies, fudge, candy, syrups) or melted plastics can cause pitting of the surface of your cooktop. This is not covered under the warranty. You should clean the spill while it is still hot. Take special care when removing hot substances. Refer to the following section.

•When using a scraper, be sure it is new and the razor blade is still sharp; do not use a dull or nicked blade.

Cleaning sugary spills and melted plastic

1.Turn off all surface units. Remove hot pans.

2.Wearing an oven mitt, use a single-edge razor-blade scraper to move the spill to a cool area of the cooktop. Remove the spill with paper towels.

3.Any remaining spillover should be left until the surface of the cooktop has cooled.

4.Don’t use the surface units again until all of the residue has been completely removed.

If pitting or indentation in the glass surface has already occurred, the cooktop glass will have to be replaced. In this case, service will be necessary.

35_ Maintaining your appliance

FE-R300_XAA_DG68-00277A-08_EN.indd 35

2013-06-11 �� 12:37:02

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Electric Range Features of your new range Important safety instructionsPersonal injury when using your oven, follow these basic Safety precautionsANTI-TIP Device Hazards or unsafe practices that may result in minorFor Your Safety Do not enter inside the oven Surface Cooking Units Oven Ventilating HoodSELF-CLEANING Ovens GLASS/CERAMIC Cooking SurfacesBefore YOU Begin Important safety instructions Features of your new range Important safety instructions Features of your new range State of California Proposition Contents Introducing your new range OverviewWHAT’S Included with Your Range Surface cooking About Surface CookingAbout the radiant surface elements HOW to SET the Appliance for Surface Cooking Hot surface indicatorLocation of the radiant surface elements and controls Cooking areasUsing the Proper Cookware Dual surface unit control knob left front, right frontChoosing the Proper Cookware Protecting the Smoothtop SurfaceOperating the oven Oven Control PanelSetting the Clock Setting the Kitchen TimerHow to set the clock How to change between a 12-hour and 24-hour displayMinimum and Maximum Settings Using the Oven RacksBefore using the racks Oven rack positionsHow to set the thermostat How to adjust the thermostat while cookingHow to set the oven for timed cooking BakingDelay Timed Cooking How to set the oven for delay timed cookingHow to set the oven for broiling BroilingBroil stop position Recommended broiling guideUsing the Easy Cook Feature Slow CookChicken Nuggets ProofUsing the Custom Cook Feature Using the Warm FunctionHow to record a recipe setting How to recall a settingExtra Features Fahrenheit or Celsius temperature selectionThermostat adjustment Hour energy savingSound on/off Control lockoutSetting the Sabbath For use on the Jewish Sabbath & HolidaysSELF-CLEANING Before a self-cleaning cycleMaintaining your appliance How to set the oven for self-cleaning How to delay the start of self-cleaningHow to turn off the self-cleaning feature After a self-cleaning cycleSTEAM-CLEANING How to set the oven for steam-cleaningAfter a steam-cleaning cycle Care and Cleaning of the Oven Cleaning painted parts and decorative trimCleaning stainless steel surfaces Cleaning the broil pan and insertCare and Cleaning of the Glass Cooktop Normal daily use cleaningOven racks Oven doorCleaning the cooktop seal Cleaning sugary spills and melted plasticRemoving heavy, burned-on residue Removing metal marks and scratchesRemoving and Replacing the Oven Door Removing and Replacing the Storage DrawerChanging the Oven Light Troubleshooting TroubleshootingAreas Discoloration onCooktop Frequently cycles onTemperature is too Self-cleanCleaning cycle Not open after a Self-cleaning cycleOven not clean after Steam from the ventBurning or oily odor Emitting fromWarranty Limited Warranty to Original PurchaserCode No. DG68-00277A-08

FER300SB, FER300SX, FER300SBPKG, FER300SW, FER300SWPKG specifications

The Samsung FER300 series of refrigerators, comprising models such as FER300SXPKG, FER300SWPKG, FER300SW, FER300SBPKG, and FER300SX, represents a notable advancement in refrigeration technology. These refrigerators are designed with a blend of functionality, style, and energy efficiency, making them suitable for modern households.

One of the main features of the Samsung FER300 series is its spacious interior design. The refrigerators offer optimized storage solutions with adjustable shelves, allowing users to customize the layout according to their needs. This flexibility ensures that items of various shapes and sizes can be accommodated effortlessly. Additionally, the series includes multiple compartments, including crisper bins for fruits and vegetables, which help to preserve the freshness of produce for extended periods.

A key technological highlight of the FER300 series is the Digital Inverter Compressor. This technology automatically adjusts the compressor speed in response to cooling demand. As a result, these refrigerators operate more quietly and efficiently compared to traditional models. This not only enhances energy efficiency but also contributes to reduced wear and tear, leading to a longer lifespan for the appliance.

The refrigerators in the FER300 series also feature advanced cooling technologies, such as Multi-Air Flow. This system ensures that cold air is evenly distributed throughout the interior, minimizing temperature fluctuations and ensuring consistent cooling for all items within the fridge. This feature is particularly beneficial for maintaining the freshness of perishable goods.

Energy efficiency is another standout characteristic of the Samsung FER300 series. These models are designed to meet high energy-efficiency standards, helping users save on electricity bills while reducing their carbon footprint. Many of the refrigerators in this series also come with LED lighting, which not only illuminates the interior but also consumes less energy compared to traditional bulb lighting.

Furthermore, the stylish design of the FER300 models adds a modern touch to any kitchen. Available in various finishes, including stainless steel and sleek black, these refrigerators are built to blend seamlessly with a wide range of kitchen aesthetics.

In conclusion, the Samsung FER300 series represents a powerful combination of innovative features and technologies aimed at enhancing everyday living. With its focus on efficiency, functionality, and modern design, these refrigerators are an excellent choice for consumers seeking a reliable and stylish appliance.
Top Page Image Contents