Fisher & Paykel DS603M Option Adjustment Mode, How to Change Setup Options, Rinse Aid Setup rA

Page 16

March 2004

Manual 599082

4.0OPTION ADJUSTMENT MODE

4.1How to Change Setup Options

4.1.1Rinse Aid / Water Supply Hardness / Auto Power / End of Cycle Beeps / Closed Drawer Option / Clean/Dirty Dish Symbol /Dry Enhancement Option

To enter this setup mode, press Power, then hold the Eco touch switch and KeyLock button simultaneously for 5 seconds ensuring that Eco is pushed first. Once the setup mode is entered a beep is emitted and the LCD displays the letters rA. By pushing the Start/Pause button you can scroll through and change the following options:- Rinse Aid Setup (rA)

Water Supply Hardness Setup (hd) Auto Power Option (AP)

End of Cycle Beeps (EC)

Closed Drawer Option (Ld).

Clean/Dirty Dish Symbol (dS)

Dry Enhancement Option (LH)

Integrated:- On an Integrated DishDrawer, where there is no display, you can still tell which option you have chosen

by using the lights showing on the integrated badge as follows:- Rinse Aid Setup (red light above Start/Pause button)

Water Supply Hardness (green light above Start/Pause button) Auto Power Option (orange light above Start/Pause button)

End of Cycle Beeps (green light above Start/Pause and red light above Keylock) button) Closed Drawer Option (red light above Start/Pause and Keylock buttons)

Clean/Dirty Dish Symbol (not available on Integrated models)

Dry Enhancement Option (orange light above Start/Pause button, Eco light is red)

Push Power at any time to exit this setup mode.

4.1.2Rinse Aid Setup (rA)

The current rinse aid setting is shown using the red LED’s on the touch switch panel.

The amount of rinse aid dispensed into a rinse cycle can be varied to suit the level of hardness of the local water supply. It is adjusted for 1 - 5 dispenser levels

(1 = approx 0.5mls (1/10) teaspoon of rinse aid, 5 = approx. 2.5mls (½) teaspoon of rinse aid).

Push Keylock to advance the rinse aid setting. Once the desired setting is achieved, push Power to exit. The rinse aid index is stored in EE memory, so even with the power removed, the rinse aid level is retained.

Integrated:- On an Integrated DishDrawer when you turn on or turn off one of the following options it is indicated by the red wash cycle LEDs on the secondary control panel. If an option is turned on then all the LEDs turn on and if an option is turned off all the LEDs turn off.

4.1.3Water Supply Hardness Setup (hd)

The current supply hardness setting is shown using the red LED’s on the touch switch panel. One of 5 settings should be selected according to the known hardness of the supply water. Each setting is appropriate for the following water supply hardness:

No. LED

Water Softener turned off, continuous bypass of softener

1

150-250 ppm water supply hardness

2

250-350 ppm water supply hardness

3

350-450 ppm water supply hardness

4

450-550 ppm water supply hardness

5

550-625 ppm water supply hardness

 

- 16 -

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 599082 Page Changes USAN T E N T S Lockring NUT Drain Cycle Filter Plate Page Service Requirements Health & SafetySpecialised Tools Dimensions & Specifications DimensionsSpecifications ElectricalComponent Part Number Specifications Technical Overview ChassisDrawer Fronts ElectronicsWiring Cover MotorLid System TubFilling HeatingLockring Nut Drain CycleFilter Plate Drying CycleWater Softener where fitted Option Adjustment Mode How to Change Setup OptionsRinse Aid Setup rA Water Supply Hardness Setup hdAuto Power Option AP Clean/dirty Dish Symbol dSEnd of Cycle Beeps EC Closed Drawer Option LdOption Adjustment Quick Reference Charts Press Start / Pause Five times Press Start/Pause Four timesPress Start / Pause Six times Diagnostics DishDrawer DiagnosticsNorm Fast Deli Rinse Hardware Output Continuous Cycle Test ModeFast Test Cycle Show Off / Showroom Wash Mode Cycle Count RetrievalPage Fault Display/Download Mode Diagnostics Quick Reference ChartsHardware Output Test Mode Fast Test Cycle Temperature & Voltage Display ModeContinuous Cycle Fault Codes Fault Code Description Chart Fault Code LED Display Rinse LEDFault Possible CausesFault Code Problem Solving Charts F2 The motor is not sensed to be rotating F3 Water temperature sensed at greater than 85C 185FQuestion Yes F9 Electronics failure Eeprom access error Question Yes Question Yes Cause of problem How to resolve the problem Poor Dry PerformancePoor Wash Performance Poor Dry Performance Question YesCustomers Complaint Coffee/Tea Stains left in Cups C2 Water Softener Brine Pump Wiring Diagram MarchDrawer Front Removal Service ProceduresTub Removal Drawer and LCD Display Removal Drying Fan RemovalDetergent Dispenser Electronic ControllerWiring Cover Removal Rotor Assembly RemovalFilter Plate Removal Tub Disconnection Rotor Sensor RemovalLocking Ring, Element Plate and Motor Assembly Removal Lid Removal Yoke RemovalLid Actuator Removal Slide Rail Replacement Chassis Circuit Board / Flood Sensor RemovalFill Hose, Drain Hose, Wiring Harness Replacement Water Valve RemovalToe Kick Removal Lower Tub CowlingFront Trim Replacement Water Softener
Related manuals
Manual 27 pages 54.23 Kb Manual 12 pages 41.18 Kb Manual 40 pages 641 b

DS603 I, DS603H, DS603IH, DS603M, DD603I specifications

The Fisher & Paykel DS603 is an innovative and highly efficient dishwasher designed to streamline the dishwashing process while providing exceptional cleaning performance. As part of Fisher & Paykel’s commitment to sustainable living and user-friendly design, the DS603 is packed with features that enhance both functionality and convenience in the kitchen.

One of the standout features of the DS603 is its unique Drawer Dishwasher design. Unlike traditional dishwashers, which have a single, large compartment, the DS603 offers two separate drawers that can be independently operated. This allows users to run smaller loads without the need to fill an entire dishwasher, making it ideal for smaller households or quick cleanups. Additionally, each drawer can accommodate different wash cycles, enabling users to tailor the washing process for delicate glassware or heavily soiled pots and pans.

The DS603 also incorporates a variety of wash programs, including Eco, Fast, and Heavy options, ensuring that dishes are cleaned thoroughly no matter the level of soiling. The Eco wash program is particularly notable, as it uses less water and energy while still providing superb cleaning performance, aligning with modern sustainability goals.

In terms of technology, the DS603 features SmartDrive™ technology, which utilizes a direct current motor that adapts to the load size and type, optimizing the wash performance while minimizing noise. This whisper-quiet operation makes it perfect for open-plan living spaces, ensuring that household activities continue smoothly without the interruption of loud washing cycles.

Another impressive characteristic of the DS603 is its adjustable racking system. Users can configure the interior of the dishwasher to accommodate a variety of dish sizes and shapes, from tall wine glasses to bulky pots. This adaptability enhances user convenience and maximizes the efficiency of each wash cycle.

Furthermore, the DS603 is equipped with a robust water filtration system that ensures clean water is used throughout the washing process. This not only improves washing results but also protects the dishwasher’s internal components from buildup and residue.

The Fisher & Paykel DS603 stands out as a versatile, eco-friendly appliance that combines cutting-edge technology with a user-centric design. Its unique dual-drawer system, customizable wash options, and efficient water use make it a top choice for modern kitchens, reflecting Fisher & Paykel’s dedication to creating quality home appliances that simplify everyday life while being kind to the environment.
Top Page Image Contents