Fisher & Paykel Understanding DishDrawer Diagnostic Mode for Your Dishwasher
Page 20

March 2004

Manual 599082

5.0DIAGNOSTICS

5.1DishDrawer Diagnostics

DishDrawer Diagnostics can only be entered in Power Off mode, ie. When there is no display on the LCD or the badge LED’s are off. Diagnostics is entered by holding the Keylock and Start/Pause buttons simultaneously for 5 seconds. Ensure that Keylock is pushed first.

There are currently four levels of diagnostics. To move to the next level push Power. To enter a level push Start/Pause. Once a level has been entered, pushing Power will exit diagnostics completely. If no level is entered then the display will cycle through the four levels and exit after the last. On entering diagnostic mode the first level is the Display/Download Mode.

5.1.1Display / Download Mode

In this mode all LED’s and LCD segments (except keylock) are illuminated.

5.1.2Optical LED Download / Fault Display

An optical data download is available here to download all EE data to a PC or Palm PC via the lower tub-home sensor light pipe. Hold the reader pen over the lower tub-home sensor light pipe and press Start/Pause to initiate the download. A short beep indicates the start and finish of download.

In products manufactured before MEM741743, 21/5/03, the last two faults are displayed on the LCD (secondary control panel LEDs for integrated models) during the optical download, the Current Fault code is displayed first followed by the Previous Fault Code. To read the Fault Code on the secondary display for integrated and prefinished products after MEM741743, refer to Section 7.1 on Fault Codes.

5.1.3Clearing Fault Logs

To Clear the current Fault press the Keylock button until a beep is sounded. This action moves the Current Fault into the Previous Fault while clearing the Current Fault. To Clear the Previous Fault press Keylock once more until the beep is sounded.

Warning: Once a fault has been cleared, it is permanently removed from memory and cannot be recovered.

Press Power to advance to the next level.

5.1.4Hardware Output Diagnostic Test Mode

This level tests all the hardware outputs and inputs. The LCD display shows ‘HO’.

Press Power to skip hardware diagnostics and advance to the next level.

Press Start/Pause to enter hardware diagnostics.

Once hardware diagnostics has been entered letters in the LCD display indicate the current hardware output being tested and for integrated models the LEDs on the touch switch panel, using binary encoding, as shown in the table on the next page.

Different combinations of outputs can be switched on or off together but the controller will prevent higher current drawing components such as the wash pump and the lid motors being turned on together.

Press Start/Pause to advance to the next hardware output.

Press Keylock to turn the currently displayed output On or Off. If the scrubbing brush symbol (green LED above start/pause button on integrated models) is displayed then that output has been switched on, and if it is not displayed then that output is off.

- 20 -

Page 19 Page 21
Image 20
Page 19 Page 21
Contents 599082 Page Changes USAN T E N T S Lockring NUT Drain Cycle Filter Plate Page Service Requirements Health & SafetySpecialised Tools Dimensions & Specifications DimensionsSpecifications ElectricalComponent Part Number Specifications Technical Overview ChassisDrawer Fronts ElectronicsWiring Cover MotorLid System TubFilling HeatingLockring Nut Drain CycleFilter Plate Drying CycleWater Softener where fitted Option Adjustment Mode How to Change Setup OptionsRinse Aid Setup rA Water Supply Hardness Setup hdAuto Power Option AP Clean/dirty Dish Symbol dSEnd of Cycle Beeps EC Closed Drawer Option LdOption Adjustment Quick Reference Charts Press Start / Pause Six times Press Start/Pause Four timesPress Start / Pause Five times Diagnostics DishDrawer DiagnosticsFast Test Cycle Continuous Cycle Test ModeNorm Fast Deli Rinse Hardware Output Show Off / Showroom Wash Mode Cycle Count RetrievalPage Hardware Output Test Mode Diagnostics Quick Reference ChartsFault Display/Download Mode Continuous Cycle Temperature & Voltage Display ModeFast Test Cycle Fault Codes Fault Code Description Chart Fault Code LED Display Rinse LEDFault Possible CausesFault Code Problem Solving Charts Question Yes F3 Water temperature sensed at greater than 85C 185FF2 The motor is not sensed to be rotating F9 Electronics failure Eeprom access error Question Yes Question Yes Cause of problem How to resolve the problem Poor Dry PerformancePoor Wash Performance Poor Dry Performance Question YesCustomers Complaint Coffee/Tea Stains left in Cups C2 Water Softener Brine Pump Wiring Diagram MarchTub Removal Service ProceduresDrawer Front Removal Drawer and LCD Display Removal Drying Fan RemovalDetergent Dispenser Electronic ControllerFilter Plate Removal Rotor Assembly RemovalWiring Cover Removal Tub Disconnection Rotor Sensor RemovalLocking Ring, Element Plate and Motor Assembly Removal Lid Removal Yoke RemovalLid Actuator Removal Slide Rail Replacement Chassis Circuit Board / Flood Sensor RemovalFill Hose, Drain Hose, Wiring Harness Replacement Water Valve RemovalToe Kick Removal Lower Tub CowlingFront Trim Replacement Water Softener
Related manuals
Manual 27 pages 54.23 Kb Manual 12 pages 41.18 Kb Manual 40 pages 641 b

DS603 I, DS603H, DS603IH, DS603M, DD603I specifications

The Fisher & Paykel DS603 is an innovative and highly efficient dishwasher designed to streamline the dishwashing process while providing exceptional cleaning performance. As part of Fisher & Paykel’s commitment to sustainable living and user-friendly design, the DS603 is packed with features that enhance both functionality and convenience in the kitchen.

One of the standout features of the DS603 is its unique Drawer Dishwasher design. Unlike traditional dishwashers, which have a single, large compartment, the DS603 offers two separate drawers that can be independently operated. This allows users to run smaller loads without the need to fill an entire dishwasher, making it ideal for smaller households or quick cleanups. Additionally, each drawer can accommodate different wash cycles, enabling users to tailor the washing process for delicate glassware or heavily soiled pots and pans.

The DS603 also incorporates a variety of wash programs, including Eco, Fast, and Heavy options, ensuring that dishes are cleaned thoroughly no matter the level of soiling. The Eco wash program is particularly notable, as it uses less water and energy while still providing superb cleaning performance, aligning with modern sustainability goals.

In terms of technology, the DS603 features SmartDrive™ technology, which utilizes a direct current motor that adapts to the load size and type, optimizing the wash performance while minimizing noise. This whisper-quiet operation makes it perfect for open-plan living spaces, ensuring that household activities continue smoothly without the interruption of loud washing cycles.

Another impressive characteristic of the DS603 is its adjustable racking system. Users can configure the interior of the dishwasher to accommodate a variety of dish sizes and shapes, from tall wine glasses to bulky pots. This adaptability enhances user convenience and maximizes the efficiency of each wash cycle.

Furthermore, the DS603 is equipped with a robust water filtration system that ensures clean water is used throughout the washing process. This not only improves washing results but also protects the dishwasher’s internal components from buildup and residue.

The Fisher & Paykel DS603 stands out as a versatile, eco-friendly appliance that combines cutting-edge technology with a user-centric design. Its unique dual-drawer system, customizable wash options, and efficient water use make it a top choice for modern kitchens, reflecting Fisher & Paykel’s dedication to creating quality home appliances that simplify everyday life while being kind to the environment.
Top Page Image Contents