Fisher & Paykel DD603HM, DS603, DD603M, DD603I Cycle Count Retrieval, Show Off / Showroom Wash Mode

Page 22

March 2004

Manual 599082

Press Start/Pause to enter Continuous Cycle.

Once selected the LCD backlight flashes on and off to indicate the DishDrawer is in continuous cycle and the cycle starts straight away (for integrated models the LED above the start/pause button will be orange instead of green to indicate the DishDrawer is running in continuous cycle). It will run the last cycle that had been selected prior to going into diagnostics mode.

If you wish to run a different cycle you need to exit diagnostics turn the DishDrawer on as normal and select the cycle you want. Then turn the DishDrawer off again reenter diagnostics and restart the Continuous Cycle as above.

Press Power to Exit at any time.

Cycle Count Retrieval

(not available on integrated models)

To display the cycle count on the LCD screen, pause the DishDrawer while running a Continuous Cycle. The two bytes of the cycle count will be displayed alternately, in syncronisation with the changing backlight.

The Low byte is displayed when the backlight is Off. The High byte is displayed when the backlight is On.

To calculate the Total DishDrawer cycle count use the formula below.....

Cycle_Count = (200 x High_byte) + Low_byte.

Eg.

Low_byte = 156

 

High_byte = 2

 

Cycle_count = (200 x 2) + 156 = 556.

5.1.7Temperature & Voltage Display Mode (not available on integrated models)

During a wash cycle, the current water temperature or the power supply rail voltage of the controller can be displayed on the LCD instead of the time remaining. To enter temperature/voltage display mode, start a wash cycle as normal. Initiate a keylock by pushing and holding the Keylock button for 4 seconds.

Once in keylock mode push and hold Start/Pause for 8 seconds to enter temperature display mode. The display now alternates between a ￿C symbol and the water temperature. Pressing the Start/Pause again changes the display to alternate between an ￿E symbol and the power supply rail voltage of the controller.

To cancel temperature/voltage display mode, press the Power button.

5.1.8Show Off / Showroom Wash Mode

This mode initiates a shop show off display and wash operation demonstration.

With the DishDrawer powered up and turned on the show off mode is entered by holding the Eco and Power buttons simultaneously for 5 seconds. Ensure that Eco is pushed first.

The DishDrawer is now in the Show Off mode and cycles through all of the LED & LCD segments while pulsing the LCD backlight on and off.

Pressing the Power button now puts the DishDrawer into the Showroom Wash mode. Before running this mode the tub should be filled with water until it is just touching the underside of the spray arm. The Showroom Wash is started by pushing the Start/Pause button whereby the following cycle is run:-

The lid is pulled down

The wash motor starts and runs for 4 minutes The wash motor stops.

- 22 -

Image 22
Contents 599082 Page Changes USAN T E N T S Lockring NUT Drain Cycle Filter Plate Page Service Requirements Health & SafetySpecialised Tools Specifications Dimensions & SpecificationsDimensions ElectricalComponent Part Number Specifications Drawer Fronts Technical OverviewChassis ElectronicsLid System Wiring CoverMotor TubFilling HeatingFilter Plate Lockring NutDrain Cycle Drying CycleWater Softener where fitted Rinse Aid Setup rA Option Adjustment ModeHow to Change Setup Options Water Supply Hardness Setup hdEnd of Cycle Beeps EC Auto Power Option APClean/dirty Dish Symbol dS Closed Drawer Option LdOption Adjustment Quick Reference Charts Press Start / Pause Five times Press Start/Pause Four timesPress Start / Pause Six times Diagnostics DishDrawer DiagnosticsNorm Fast Deli Rinse Hardware Output Continuous Cycle Test ModeFast Test Cycle Show Off / Showroom Wash Mode Cycle Count RetrievalPage Fault Display/Download Mode Diagnostics Quick Reference ChartsHardware Output Test Mode Fast Test Cycle Temperature & Voltage Display ModeContinuous Cycle Fault Codes Fault Fault Code Description ChartFault Code LED Display Rinse LED Possible CausesFault Code Problem Solving Charts F2 The motor is not sensed to be rotating F3 Water temperature sensed at greater than 85C 185FQuestion Yes F9 Electronics failure Eeprom access error Question Yes Question Yes Poor Wash Performance Cause of problem How to resolve the problemPoor Dry Performance Poor Dry Performance Question YesCustomers Complaint Coffee/Tea Stains left in Cups C2 Water Softener Brine Pump Wiring Diagram MarchDrawer Front Removal Service ProceduresTub Removal Drawer and LCD Display Removal Drying Fan RemovalDetergent Dispenser Electronic ControllerWiring Cover Removal Rotor Assembly RemovalFilter Plate Removal Tub Disconnection Rotor Sensor RemovalLocking Ring, Element Plate and Motor Assembly Removal Lid Removal Yoke RemovalLid Actuator Removal Slide Rail Replacement Chassis Circuit Board / Flood Sensor RemovalFill Hose, Drain Hose, Wiring Harness Replacement Water Valve RemovalToe Kick Removal Lower Tub CowlingFront Trim Replacement Water Softener
Related manuals
Manual 27 pages 54.23 Kb Manual 12 pages 41.18 Kb Manual 40 pages 641 b

DS603 I, DS603H, DS603IH, DS603M, DD603I specifications

The Fisher & Paykel DS603 is an innovative and highly efficient dishwasher designed to streamline the dishwashing process while providing exceptional cleaning performance. As part of Fisher & Paykel’s commitment to sustainable living and user-friendly design, the DS603 is packed with features that enhance both functionality and convenience in the kitchen.

One of the standout features of the DS603 is its unique Drawer Dishwasher design. Unlike traditional dishwashers, which have a single, large compartment, the DS603 offers two separate drawers that can be independently operated. This allows users to run smaller loads without the need to fill an entire dishwasher, making it ideal for smaller households or quick cleanups. Additionally, each drawer can accommodate different wash cycles, enabling users to tailor the washing process for delicate glassware or heavily soiled pots and pans.

The DS603 also incorporates a variety of wash programs, including Eco, Fast, and Heavy options, ensuring that dishes are cleaned thoroughly no matter the level of soiling. The Eco wash program is particularly notable, as it uses less water and energy while still providing superb cleaning performance, aligning with modern sustainability goals.

In terms of technology, the DS603 features SmartDrive™ technology, which utilizes a direct current motor that adapts to the load size and type, optimizing the wash performance while minimizing noise. This whisper-quiet operation makes it perfect for open-plan living spaces, ensuring that household activities continue smoothly without the interruption of loud washing cycles.

Another impressive characteristic of the DS603 is its adjustable racking system. Users can configure the interior of the dishwasher to accommodate a variety of dish sizes and shapes, from tall wine glasses to bulky pots. This adaptability enhances user convenience and maximizes the efficiency of each wash cycle.

Furthermore, the DS603 is equipped with a robust water filtration system that ensures clean water is used throughout the washing process. This not only improves washing results but also protects the dishwasher’s internal components from buildup and residue.

The Fisher & Paykel DS603 stands out as a versatile, eco-friendly appliance that combines cutting-edge technology with a user-centric design. Its unique dual-drawer system, customizable wash options, and efficient water use make it a top choice for modern kitchens, reflecting Fisher & Paykel’s dedication to creating quality home appliances that simplify everyday life while being kind to the environment.