GE ZIRS36N RH Tools, Required, Materials, Hardware, Supplied, Recommendations, Flooring

Page 8

 

 

 

 

Installation Preparation

 

 

 

 

 

 

 

 

 

 

 

 

 

36" Stainless Steel Refrigerators, Freezers

 

 

 

 

 

 

 

 

Tools

• Tinsnips to cut banding

• Appliance hand truck

• Drill and appropriate bits

 

Required

• Stepladder

• Tubing cutter

• 7/16" socket with 3" extension for

 

 

 

 

• Bucket

• 7/16" open-end wrench

ratchet

 

 

 

 

• Level

• #2 Phillips screwdriver

• Safety glasses

 

 

 

 

• 1-1/4" open-end wrench

• Stubby Phillips screwdriver

 

 

 

 

 

 

 

Materials

• 2x4, 35" long, for Anti-Tip support, see page 10

• Water shut-off valve

 

Required

• Stick-on hook and loop fastener strips for 1/4" side panels

• Screws to secure refrigerator to cabinetry

 

 

 

 

• 1/4" copper water line tubing or GE SmartConnect™ Tubing Kit

 

 

 

 

 

 

 

 

Hardware

• 1/4-1/4 union with nuts

 

 

 

Supplied

• Anti-tip mounting brackets

 

 

 

 

 

 

 

 

 

Hardware

• Water shut-off valve

 

 

 

Recommendations

• Water filter WR97X0214

 

 

 

Flooring

For proper installation, the refrigerator and freezer must

 

be placed on a level surface of hard material that is at

 

the same height as the rest of the flooring. The floor

 

must be strong enough to support a fully loaded product,

 

or approximately 1,200 lbs.

NOTE: Protect the finish of the flooring. Cut a large section of the cardboard carton and place under the product where you are working.

Step 1

Remove

Packaging

8

CAUTION

Refrigerator is much heavier at the top than at the bottom – be careful when moving. When using a hand truck, handle from side only.

PRUDENCE

Le réfrigérateur est beaucoup plus lourd en haut qu’en bas. Il faut être prudent lors des déplacements. Si un diable est utilisé, il faut soulever le réfrigérateur sur le côté seulement.

•Remove outer carton.

–Carefully cut banding at the top and bottom.

•Slide out back corner posts (2).

•Slide carton off top of cabinet.

•Remove styrofoam pads taped to base cabinet.

NOTE: IT IS NOT NECESSARY TO LAY CABINET DOWN IN ORDER TO REMOVE SKID!

•The unit is secured to the skid with 3 slotted tie-down straps. First remove the 5/16" bolts from the base channels in the tie-downs, then remove the 7/16" bolts securing the straps to the skid.

•Protect the flooring. Cut a large piece of the card- board carton and place under the product where you are working.

•Support blocks on the bottom must be removed before the refrigerator is taken off the skid or damage will occur. Remove support blocks by carefully tilting cabinet to side and sliding out.

•Lift the refrigerator off the skid with an appliance dolly. Handle from the sides.

7/16" Bolt

CAUTION

DO NOT ATTEMPT TO ROLL UNIT OFF SKID.

PRUDENCE

IL NE FAUT PAS ESSAYER DE FAIRE ROULER LE

RÉFRIGÉRATEUR POUR L'ENLEVER DE LAY PALETTE.

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Page Contents Flush or Semi-Flush Enclosure Installations DimensionsCutout ProductSide By Side Installation Freezer Refrigerator Accessory Grille Panel KitsInstallation Between Base Wall Cabinets ExamplesInstallation At End-of-Run Product DimensionsFrameless Cabinets ZIRS36N RH, Refrigerator ZIFS36N RH, FreezerClearances ElectricalWater ConnectionGrounding Important Please read carefullyUse of Adapter plug Use of Extension CordsTools RequiredMaterials HardwareInstall StepWater Line Shut off the main water supplyStep Install Side Panels Anti-Tip BracketsLevel Secure Product to SidesCheck Power ConnectOn the unit and tighten nut to union Turn on the water to check for leaksAdjust Door Step Set temperature control at TemperatureBefore making adjustments ProblemTools and Materials Required Parts ListStep Install Spacer Pads Replace Side Case Trims Step Level Both Products Step Install Anti-Tip BracketsRoll Both Products into Opening Remove 3 screws holding the wire fence on both Step Secure Products To SidesGrille Base Cover Products. Retain fences and all screwsStep Install Grille Base Cover Remove Grille Frame Mount Outside case trim Unified Grille Panel Step Install Soffit Vent TopReinstall Screws Step Adjust Door Alignment Pub. No Part No D3003P001

ZIRS36N LH, ZIFS36N LH, ZIFS36N RH, ZIRS36N RH specifications

The GE ZIRS36N RH, ZIFS36N RH, ZIFS36N LH, and ZIRS36N LH are part of General Electric's innovative line of side-by-side refrigerators, designed to meet the needs of modern households while providing exceptional performance and convenience. These models are characterized by a sleek and stylish exterior, making them an attractive addition to any kitchen.

One of the standout features of these refrigerators is their advanced cooling technology. They incorporate a multi-air flow system that ensures even distribution of cold air throughout the refrigerator and freezer compartments. This technology helps maintain optimal temperature levels, keeping food fresher for longer, while also minimizing temperature fluctuations that can lead to spoilage.

These models are equipped with energy-efficient LED lighting that illuminates the interior, making it easy to find items even in low light conditions. The LED lights consume less energy compared to traditional incandescent bulbs, contributing to lower electricity bills and a more sustainable operation.

The GE ZIRS36N and ZIFS36N series also feature adjustable shelving, allowing users to customize the interior layout to accommodate various food items and containers. This flexibility is essential for maximizing storage space and ensuring that everything fits perfectly. Additionally, spill-proof shelves are included, which are designed to contain spills for easy cleanup and to prevent messes from spreading to other compartments.

For added convenience, these refrigerators are designed with a fresh food compartment that includes humidity-controlled crispers. These crispers help maintain the freshness of fruits and vegetables by regulating humidity levels, which is vital for preserving their quality.

Security and access are also a priority, as these models come with external water and ice dispensers. This feature provides instant access to cold water and ice without having to open the refrigerator door, promoting energy efficiency and convenience in daily routines.

In terms of design, the GE ZIRS36N RH, ZIFS36N RH, ZIFS36N LH, and ZIRS36N LH models are finished in high-quality stainless steel, giving them a modern and professional look that enhances any kitchen décor. Their reversible doors offer flexibility for kitchen layouts, allowing the user to configure the fridge to suit their space.

Overall, the GE ZIRS36N RH, ZIFS36N RH, ZIFS36N LH, and ZIRS36N LH refrigerators combine modern technology, user-friendly features, and a stylish design, making them ideal choices for families seeking functionality and efficiency in their kitchen appliances.
Top Page Image Contents