GE ZIRS36N LH, ZIRS36N RH Step Install Anti-Tip Brackets, Roll Both Products into Opening

Page 15

ZUGSS Trim Kit

Unified Stainless Steel Grille Panel

Step 2

Install

Anti-Tip

Brackets

WARNING

ANTI-TIP PRECAUTIONS

These products are heavy at the top and must be secured to prevent the possibility of tipping over.

ATTENTION

PRECAUTIONS CONTRE LES BASCULEMENTS

Le réfrigérateur est beaucoup plus lourd en haut et il faut le maintenir en place pour éviter la possibilité de son basculement vers l’avant.

Brackets Block Required

2 x 4 Cut 71" Length

Soffit

Height

From

Floor

to

Bottom

of Wood

Block

Side View

Brackets

Not Required

Beneath a

Soffit

•Cut a 2"x4" block, 71" long. Secure the 2"x4" to the 4 mounting brackets provided using #12 or #14 wood screws.

•Secure the brackets with wood block to the back wall so that it is 84" (or your installation height) from the finished floor. Use #12 or #14 wood screws. See illustration.

•Screws must penetrate at least one inch into vertical wall studs.

Roll Both Products into Opening

•Gently push each product into opening with hands against front corners. Push back into the opening until it is flush or semi-flush with adjacent cabinets.

Installation Mounting

Height Bracket

From Floor

Screws Mounted into

Vertical Wall Studs

IMPORTANT NOTE: When the products are installed under a soffit or if there is not enough height for this method of security, use Step 4 as an alternative. The refrigerator and

freezer must be secured to prevent tipping.

Step 3

Level Both

Products

Both products MUST BE LEVEL AND PLUMB with each other and adjacent cabinetry on each side. Toekick heights should align with cabinetry.

•Adjust carefully. Both models have 4-point leveling. The front is supported by leveling legs, the rear is supported by wheels.

•Raise units to the same level, aligning with adjacent toekick heights.

•Adjust rear wheels beneath the product to just barely touch the 2x4 block.

•Turn the 7/16" hex nut located above the front wheels to raise or lower the back of the refrigerator.

•To adjust the front leveling legs: Use a 1/4" angled wrench to turn the top of the leveling leg, or turn the bottom of the legs with a 1-1/4" wrench.

Hex Nut Adjusts

Rear Wheels

Leveling Leg

Units must be 1" apart and evenly aligned at top and bottom. The inside case trims must align, top and bottom.

CAUTION

The rear leveling wheels and front leveling legs are limited to a maximum height adjustment of 1". If the installation requires more than 84-1/2" height, the installer should elevate the refrigerator on a sheet of plywood or runners. Cabinetry trim could also be added across the top of the opening to shorten the opening. If you attempt to raise the refrigerator more than 1", you will damage the front leveling legs and rear leveling wheels.

PRUDENCE

Les roues de nivellement arrière et les pattes de nivellement avant permettent un réglage maximal de 25 mm (1 po). Si l’ouverture pour le réfrigérateur a une hauteur supérieure à 2,15 m (84-1/2 po), l’installateur doit élever le réfrigérateur sur une feuille de contre-plaqué ou des glissières. Il est également possible d’ajouter des baguettes de finition des placards sur le haut de l’ouverture afin de la réduire. Lever le réfrigérateur de plus de 25 mm (1 po) endommage les pattes de nivellement avant et les roues de nivellement arrière.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Page Contents Product Flush or Semi-Flush Enclosure InstallationsDimensions CutoutExamples Side By Side Installation Freezer RefrigeratorAccessory Grille Panel Kits Installation Between Base Wall CabinetsZIRS36N RH, Refrigerator ZIFS36N RH, Freezer Installation At End-of-RunProduct Dimensions Frameless CabinetsConnection ClearancesElectrical WaterUse of Extension Cords GroundingImportant Please read carefully Use of Adapter plugHardware ToolsRequired MaterialsShut off the main water supply InstallStep Water LineAnti-Tip Brackets Step Install Side PanelsSecure Product to Sides LevelTurn on the water to check for leaks Check PowerConnect On the unit and tighten nut to unionProblem Adjust DoorStep Set temperature control at Temperature Before making adjustmentsParts List Step Install Spacer Pads Replace Side Case TrimsTools and Materials Required Step Install Anti-Tip Brackets Roll Both Products into OpeningStep Level Both Products Products. Retain fences and all screws Remove 3 screws holding the wire fence on bothStep Secure Products To Sides Grille Base CoverStep Install Grille Base Cover Remove Grille Frame Step Install Soffit Vent Top Reinstall ScrewsMount Outside case trim Unified Grille Panel Step Adjust Door Alignment Pub. No Part No D3003P001

ZIRS36N LH, ZIFS36N LH, ZIFS36N RH, ZIRS36N RH specifications

The GE ZIRS36N RH, ZIFS36N RH, ZIFS36N LH, and ZIRS36N LH are part of General Electric's innovative line of side-by-side refrigerators, designed to meet the needs of modern households while providing exceptional performance and convenience. These models are characterized by a sleek and stylish exterior, making them an attractive addition to any kitchen.

One of the standout features of these refrigerators is their advanced cooling technology. They incorporate a multi-air flow system that ensures even distribution of cold air throughout the refrigerator and freezer compartments. This technology helps maintain optimal temperature levels, keeping food fresher for longer, while also minimizing temperature fluctuations that can lead to spoilage.

These models are equipped with energy-efficient LED lighting that illuminates the interior, making it easy to find items even in low light conditions. The LED lights consume less energy compared to traditional incandescent bulbs, contributing to lower electricity bills and a more sustainable operation.

The GE ZIRS36N and ZIFS36N series also feature adjustable shelving, allowing users to customize the interior layout to accommodate various food items and containers. This flexibility is essential for maximizing storage space and ensuring that everything fits perfectly. Additionally, spill-proof shelves are included, which are designed to contain spills for easy cleanup and to prevent messes from spreading to other compartments.

For added convenience, these refrigerators are designed with a fresh food compartment that includes humidity-controlled crispers. These crispers help maintain the freshness of fruits and vegetables by regulating humidity levels, which is vital for preserving their quality.

Security and access are also a priority, as these models come with external water and ice dispensers. This feature provides instant access to cold water and ice without having to open the refrigerator door, promoting energy efficiency and convenience in daily routines.

In terms of design, the GE ZIRS36N RH, ZIFS36N RH, ZIFS36N LH, and ZIRS36N LH models are finished in high-quality stainless steel, giving them a modern and professional look that enhances any kitchen décor. Their reversible doors offer flexibility for kitchen layouts, allowing the user to configure the fridge to suit their space.

Overall, the GE ZIRS36N RH, ZIFS36N RH, ZIFS36N LH, and ZIRS36N LH refrigerators combine modern technology, user-friendly features, and a stylish design, making them ideal choices for families seeking functionality and efficiency in their kitchen appliances.
Top Page Image Contents