GE RM25 Adjusting the Height Between the Doors, Making small adjustments between doors

Page 23

ADJUSTING THE HEIGHT BETWEEN THE DOORS

Making small adjustments between doors.

If the door of fridge is lower than that of the freezer,

adjustment part

1)If you open the Fresh Select Zone Door (➀), you can see the hinge-mid (➁).

2)Insert enclosed hex wrench (➂) into the shaft (➃) of the hinge mid.

3)Please adjust the height difference between the doors turning the hex wrench (➂) clockwise ( )

or counter clockwise ( ).

When you turn counter clockwise ( ), the door goes up.

NOTE

4)After adjusting the doors, please insert enclosed fastener-ring (➄) using a plier (➅) in the gap between the hinge-grommet (➆) and the hinge-mid (➇).

The number of the fastener-ring to insert depends on the gap.

Four fastener-rings are enclosed with the refrigerator.

NOTE

INSTALLATION INSTRUCTIONS

Image 23

Contents Side by Side Refrigerator Differ slightly from those described in this manual Safety Warning SignsSafety Warning Signs TDM System Time-Divided-Multi-Evaporator system Setting UP the RefrigeratorMajor Features Freezer Button Control PanelFreezer Fridge Digital PanelTemperature Control Upper Drawer Upper Drawer Shelves and BinsFreezer & Fridge Arctic Select ZoneTM and Fresh Select ZoneTMTempered Glass Shelf Food Storage GuideIce Chute Door Bin Tilt PocketDairy Compartment Tempered Spill Proof Glass ShelfEgg Container on some models Fruit & Vegetable DrawerArctic Select Zonetm Drawer Guide Freeze function keeps the freezer setting temperatureFresh Function Fresh Select Zonetm Drawer GuideRemoving the Fridge Accessories Removing the Freezer AccessoriesBeverage Stationtm on Some Models Empty the basket first before taking it out Open the Arctic Select Zone DoorEmpty the basket before taking it out Open the Fresh Select Zone DoorCleaning the Accessories Air duct, then pull out Changing the Interior LightPush both sides of the upper Push both sides of the bottom Lamp cover, marked onReplace the lamp with a new one Rear hook rear hook Front hookWater Filter Water Filter Indicator lightUsing the dispenser without the water filter Ordering replacement filtersSelecting the Location for the Refrigerator Installation of the RefrigeratorChecking the Dimensions of your Entrance Door Appliance is level Turn the left adjusting leg in the directionArrow with a flat head screwdriver until ➀ Driver ➁ Control Lever Making small adjustments between doors Adjusting the Height Between the DoorsAdjusting the Height Between the Doors Lift the door straight up Removing the Refrigerator DoorsRemoving the Front Leg Cover Removing the Freezer DoorRemoving the Refrigerator Doors Removing the Fridge Door Zone Door How to Disassemble the Arctic Select Zone DoorHow to Disassemble the Fresh Select Zone Door Reattaching the Freezer Door Reattaching the Refrigerator DoorsReattaching the Fridge Door Reattaching the Refrigerator DoorsReattaching the Front Leg Cover Maker to the off position Follow the instructions in the ice maker installation kitChecking the Water Dispenser Line Shut off the main water supply line and turn the IceInstallation of the Water Dispenser Line Close the filter cartridge cover Insert the filter as shown and Push until you hear a clickCheck the amount of water supplied to the ice tray Start the Icemaker Important Facts About Your DispenserWater Supply to the Icemaker Icemaker must be connected to a cold water lineBefore YOU Call for Service Warm on some models Slow ice cube freezingCube dispenser does not Workon some modelsContact Samsung World Wide Ambient Room Temperature Limits

RM25 specifications

The GE RM25 is a powerful and versatile gas turbine engine specifically designed for a variety of applications, including aviation and industrial settings. With its innovative technologies and impressive performance characteristics, the RM25 has established itself as a reliable choice for clients looking for efficiency and durability.

One of the standout features of the GE RM25 is its high thrust-to-weight ratio, which allows the engine to produce significant power while maintaining a relatively low mass. This attribute is particularly beneficial for aircraft, where weight reduction is crucial for enhancing flight performance and fuel efficiency. The engine’s design incorporates advanced materials that contribute to its light weight without compromising strength or reliability.

The RM25 employs a sophisticated modular design, making it easier to maintain and service compared to conventional gas turbines. This modularity ensures that individual components can be easily replaced or repaired, reducing downtime and optimizing operational efficiency. The engine’s service intervals have been extended, allowing for longer operational periods between maintenance checks.

GE's commitment to innovation is evident in the use of cutting-edge technologies within the RM25. The engine features a state-of-the-art digital control system that enhances its performance, providing real-time monitoring and adjustments to optimize fuel consumption and emissions. This technology helps in achieving better environmental compliance, a crucial aspect in today’s aviation and industrial landscapes.

Another key characteristic of the RM25 is its adaptability. The engine can be configured for various operating conditions, making it suitable for a wide range of missions and usages. This versatility is complemented by the engine’s ability to operate efficiently across different altitudes and temperatures, making it a reliable choice for clients in diverse environments.

Finally, the GE RM25 is recognized for its robust safety features, designed to ensure the utmost reliability in high-stakes operations. The engine undergoes rigorous testing and quality assurance processes to maintain the highest standards of performance and safety.

In conclusion, the GE RM25 gas turbine engine represents a remarkable fusion of power, efficiency, and innovation. Its combination of advanced technologies, modular components, and adaptability make it an attractive option for various applications, solidifying its reputation in the industry as a leading choice for reliable performance.