GE TAX2, TAX3 owner manual OperatingInstructions, TroubleshootingTips, CustomerService

Page 4

Safety Instructions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.

OperatingInstructions

The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.

If you have only a standard 2-prong wall outlet, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.

The refrigerator should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate.

This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.

Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.

When moving the refrigerator away from the wall, be careful not to roll over or damage the power cord.

InstallationInstructions

USE OF ADAPTER PLUGS

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an adapter plug.

TroubleshootingTips

However, if you must use an adapter, where local codes permit, a temporary connection may be made to a properly grounded 2-prong wall outlet by use of a UL-listed adapter available at most local hardware stores.

The larger slot in the adapter must be aligned with the larger slot in the wall outlet to provide proper polarity in the connection of the power cord.

When disconnecting the power cord from the adapter, always hold the adapter in place with one hand while pulling the power cord plug with the other hand. If this is not done, the adapter ground terminal is very likely to break with repeated use.

If the adapter ground terminal breaks, DO NOT USE the refrigerator until a proper ground has been established.

Attaching the adapter ground terminal to a wall outlet cover screw does not ground the appliance unless the cover screw is metal, and not insulated, and the wall outlet is grounded through the house wiring. You should have the circuit checked by a qualified electrician to make sure the outlet is properly grounded.

CustomerService

Read and follow this Safety Information carefully.

SAVE THESE INSTRUCTIONS

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Refrigerators Customer Service Service PartnershipCongratulations Tips Customer Service InstallationOperating Instructions Before You Throw Away Your Old Refrigerator or FreezerCustomerService TroubleshootingTipsOperatingInstructions About the control on the refrigerator Control SettingsAbout the inside of the refrigerator Care and cleaning of the refrigerator TroubleshootingTips CustomerServiceCleaning the Outside Cleaning the InsideSafety Instructions Behind the RefrigeratorPreparing for Vacation Preparing to MovePreparing to install the refrigerator SafetyInstructionsRefrigerator Location ClearancesBefore you call for service… Wiring diagram TAX2 TAX3Safety Instructions Operating Instructions Troubleshooting TipsGE Will Replace What GE Will Not CoverService Telephone Numbers

TAX3, TAX2 specifications

GE TAX2 and TAX3 are advanced gas turbine systems developed by General Electric, renowned for their efficiency, reliability, and innovative technologies. These turbines cater to the evolving energy demands across various sectors, including power generation and industrial applications.

The GE TAX2 model is notable for its enhanced turbine performance, achieving higher efficiency and lower emissions compared to its predecessors. One of its main features is the advanced aerodynamics of the blades, designed with computational fluid dynamics (CFD) to optimize airflow and reduce drag. This results in improved thermal efficiency, which translates to lower fuel consumption and operational costs.

Incorporating state-of-the-art materials, the TAX2 employs advanced alloys that can withstand extreme temperatures, thereby increasing the durability and lifespan of the turbine components. This resilience is crucial in maintaining consistent performance and reducing the frequency of maintenance interventions. Additionally, the turbo machinery utilizes a modular design, allowing for easier upgrades and servicing.

The GE TAX3 model builds upon the innovations of the TAX2, introducing features that focus on even greater operational flexibility and environmental responsibility. It is equipped with a dual-fuel capability, enabling it to operate efficiently on both natural gas and liquid fuels, making it an ideal choice for regions with fluctuating fuel availability. The TAX3 also features an integrated emission control system designed to minimize nitrogen oxides (NOx) and carbon dioxide emissions, thus aligning with global environmental standards.

Both models utilize GE's well-established Digital Wind Farm technology, leveraging data analytics and machine learning to enhance performance monitoring and predictive maintenance. This not only optimizes efficiency but also minimizes downtime, ensuring that facilities operate seamlessly.

Overall, the GE TAX2 and TAX3 turbine systems exemplify modern engineering excellence, offering significant advancements in efficiency, adaptability, and reduced environmental impact. As industries transition to cleaner energy solutions, these turbines represent a substantial leap forward, facilitating a sustainable energy future while meeting the demands of a dynamic global market.
Top Page Image Contents