GE 197D7799P001 Shut OFF the Main Water Supply and Unplug Refrigerator, Fasten the Shutoff Valve

Page 11

Installation Instructions

Install the shutoff valve on the nearest frequently used drinking water line.

1SHUT OFF THE MAIN WATER SUPPLY AND UNPLUG REFRIGERATOR

Turn on the nearest faucet (counterclockwise) long enough to clear the line of water.

2DRILL THE HOLE FOR THE VALVE

Choose a location for the valve that is easily accessible. It is best to connect into the side of a vertical water pipe. When it is necessary to connect into a horizontal water pipe, make the connection to the top or side, rather than at the bottom, to avoid drawing off any sediment from the water pipe.

Drill a 1/4″ hole in the water pipe (even if using a self-piercing valve), using a sharp bit. Remove any burrs resulting from drilling the hole in the pipe.

Take care not to allow water to drain into the drill. Failure to drill a 1/4″ hole may result in reduced ice production or smaller cubes.

3FASTEN THE SHUTOFF VALVE

Fasten the shutoff valve to the cold water pipe with the pipe clamp.

Tighten the clamp screws until the sealing washer begins to swell.

NOTE: Do not overtighten or you may crush the tubing.

4ROUTE THE TUBING

Route the tubing between the cold water line and the refrigerator.

Route the tubing through a hole drilled in the wall or floor (behind the refrigerator or adjacent base cabinet) as close to the wall as possible.

NOTE: Be sure there is sufficient extra tubing (about 8 feet [244 cm] coiled into 3 turns of about 10 ″ [25 cm] diameter) to allow the refrigerator to move out from the wall after installation.

5CONNECT THE TUBING TO THE VALVE

Place the compression nut and ferrule (sleeve) for copper tubing onto the end of the tubing and connect it to the shutoff valve.

Make sure the tubing is fully inserted into the valve. Tighten the compression nut securely.

For plastic tubing from a GE SmartConnectRefrigerator Tubing kit, insert the molded end of the tubing into the shutoff valve and tighten compression nut until it is hand tight, then tighten one additional turn with a wrench. Overtightening may cause leaks.

 

Compression

Saddle-Type

Nut

SmartConnect

Shutoff Valve

 

Tubing

Packing Nut

 

Outlet Valve

Ferrule (sleeve)

NOTE: Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.

Pipe Clamp

Clamp Screw

Saddle-Type Shutoff Valve

Washer

Inlet End

Vertical Cold

Water Pipe

6FLUSH OUT THE TUBING

Turn the main water supply on (counterclockwise) and flush out the tubing until the water is clear.

Shut the water off at the water valve after about one quart (1 liter) of water has been flushed through the tubing.

NOTE: Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.

11

Image 11
Contents Write the model and serial numbers here Model # Serial # RefrigeratorsRéfrigérants TroubleshootingTipsRefrigerants Tips Consumer Support Operating Instructions InstallationInstructions Troubleshooting Consumer InstallationInstructionsSupport TroubleshootingTips OperatingInstructionsAbout the fresh food compartment shelves About the temperature control dialFruit and Vegetable Drawers About the freezer compartment shelvesAbout the storage drawers Step ShelfAbout the automatic icemaker Safety Instructions OperatingTroubleshooting Tips Consumer Support About storage drawer and cover removalConsumer Care and cleaning of the refrigeratorSupport Rollers and Leveling Legs Before YOU BeginRefrigerator Location ClearancesWhat YOU will Need Installing the Water Line on Some ModelsBefore YOU Begin Route the Tubing Shut OFF the Main Water Supply and Unplug RefrigeratorDrill the Hole for the Valve Fasten the Shutoff ValveStart the Icemaker Installing the Water LineTurn the Water On AT Shutoff Valve Plug in the RefrigeratorRemove the Freezer Door Reversing the Door SwingImportant Notes Tools RequiredRemove the Fresh Food Door Reversing the HardwareTransfer fresh food door handle Reversing the Door HandlesReversing the Door Handles RE-HANGING the DoorsNormal operating sounds Before you call for service…Instructions Safety InstructionsCustomer Warranty Consumer Product Ownership Registration For refrigerators installed in the U.S GE Consumer & Industrial What GE Will Not Cover Instructions TroubleshootingGE Will Replace GE Appliances Website

197D7799P001 specifications

The GE 197D7799P001 is a cutting-edge component designed for use in various industrial and commercial applications, primarily focusing on enhancing operational efficiency and reliability. This model exemplifies GE's commitment to innovation and performance, which is evident in its advanced features, technologies, and characteristics.

At its core, the 197D7799P001 is engineered to deliver exceptional performance in demanding environments. One of its standout features is its robust design, which allows it to withstand high levels of stress and abrasion. This durability ensures that the component can operate effectively even in harsh conditions, making it a reliable choice for industries such as power generation, oil and gas, and manufacturing.

One of the key technologies integrated into the 197D7799P001 is advanced sensor technology. This feature enables real-time monitoring of performance metrics, which aids in predictive maintenance and reduces the likelihood of unexpected failures. With the ability to provide accurate data, operators can make informed decisions that enhance overall system efficiency and minimize downtime.

Another significant characteristic of the GE 197D7799P001 is its compatibility with various automation systems. The component is designed to seamlessly integrate with existing infrastructure, providing an adaptable solution for various applications. This interoperability is crucial for facilities looking to upgrade their systems without incurring extensive costs associated with complete overhauls.

The component also boasts enhanced connectivity features that support remote monitoring and troubleshooting. By utilizing industry-standard communication protocols, the 197D7799P001 allows operators to access crucial data from anywhere, thus facilitating quicker response times and improving overall operational efficiency.

Furthermore, the GE 197D7799P001 is known for its energy efficiency, contributing to reduced operational costs. Its design minimizes energy consumption while maintaining peak performance levels, aligning with global efforts towards sustainability and resource conservation.

In conclusion, the GE 197D7799P001 is a highly versatile component that combines durability, advanced sensor technology, and energy efficiency. Its ability to integrate with existing systems, coupled with robust monitoring capabilities, makes it an invaluable asset for industries aiming to enhance productivity and operational reliability. As industries continue to evolve, components like the GE 197D7799P001 will play a crucial role in shaping their future.