GE 197D7799P001 Installing the Water Line, Turn the Water On AT Shutoff Valve, Start the Icemaker

Page 12

Installation Instructions

1INSTALLING THE WATER LINE (CONT.)

7CONNECT THE TUBING TO THE REFRIGERATOR

NOTES:

•Before making the connection to the refrigerator, be sure the refrigerator power cord is not plugged into the wall outlet.

•We recommend installing a water filter if your water supply has sand or particles that could clog the screen of the refrigerator’s water valve. Install it in the water line near the refrigerator. If using GE SmartConnect™ Refrigerator Tubing kit, you will need an additional tube (WX08X10002) to connect the filter. Do not cut plastic tube to install filter.

Remove the access cover.

Remove the plastic flexible cap from the water valve (refrigerator connection).

Place the compression nut and ferrule (sleeve) onto the end of the tubing as shown. On GE SmartConnect™ Refrigerator Tubing kit,

the nuts are already assembled to the tubing.

Insert the end of the tubing into the water valve connection as far as possible. While holding the tubing, tighten the fitting.

For plastic tubing from a GE SmartConnect™ Refrigerator Tubing kit, insert the molded end of the tubing into the shutoff valve and tighten compression nut until it is hand tight, then tighten one additional turn with a wrench. Overtightening may cause leaks.

Fasten the tubing into the clamp provided

to hold it in a vertical position. You may need to pry open the clamp.

1/4″ Copper

Tubing Clamp

Tubing

 

 

1/4″ Compression

 

Nut

 

Ferrule (sleeve)

 

SmartConnect™

Refrigerator Connection

Tubing

 

Reattach the access cover.

8TURN THE WATER

ON AT THE

SHUTOFF VALVE

Tighten any connections that leak.

9PLUG IN THE REFRIGERATOR

Arrange the coil of tubing so that it does not vibrate against the back of the refrigerator or against the wall. Push the refrigerator back to the wall.

10 START THE ICEMAKER

On power switch models, set the icemaker power switch to the l (on) position. On feeler arm models, move the feeler arm to the ON (down) position. The icemaker will not begin to operate until it reaches its operating temperature of 15°F (–9°C) or below. It will then begin operation automatically.

Power switch

Power switch model

Feeler Arm in the

STOP (up) position

Feeler Arm in

the ON (down) position

Feeler arm model

NOTE: In lower water pressure conditions, the water valve may turn on up to 3 times to deliver enough water to the icemaker.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Refrigerators Write the model and serial numbers here Model # Serial #TroubleshootingTips RefrigerantsRéfrigérants Operating Instructions Installation Instructions TroubleshootingTips Consumer Support InstallationInstructions Support TroubleshootingTipsOperatingInstructions ConsumerAbout the temperature control dial About the fresh food compartment shelvesAbout the freezer compartment shelves About the storage drawersStep Shelf Fruit and Vegetable DrawersSafety Instructions Operating Troubleshooting Tips Consumer SupportAbout storage drawer and cover removal About the automatic icemakerCare and cleaning of the refrigerator SupportConsumer Before YOU Begin Refrigerator LocationClearances Rollers and Leveling LegsInstalling the Water Line on Some Models Before YOU BeginWhat YOU will Need Shut OFF the Main Water Supply and Unplug Refrigerator Drill the Hole for the ValveFasten the Shutoff Valve Route the TubingInstalling the Water Line Turn the Water On AT Shutoff ValvePlug in the Refrigerator Start the IcemakerReversing the Door Swing Important NotesTools Required Remove the Freezer DoorReversing the Hardware Remove the Fresh Food DoorReversing the Door Handles Transfer fresh food door handleRE-HANGING the Doors Reversing the Door HandlesBefore you call for service… Normal operating soundsSafety Instructions InstructionsCustomer Warranty Consumer Product Ownership Registration For refrigerators installed in the U.S GE Consumer & Industrial Instructions Troubleshooting GE Will ReplaceWhat GE Will Not Cover GE Appliances Website

197D7799P001 specifications

The GE 197D7799P001 is a cutting-edge component designed for use in various industrial and commercial applications, primarily focusing on enhancing operational efficiency and reliability. This model exemplifies GE's commitment to innovation and performance, which is evident in its advanced features, technologies, and characteristics.

At its core, the 197D7799P001 is engineered to deliver exceptional performance in demanding environments. One of its standout features is its robust design, which allows it to withstand high levels of stress and abrasion. This durability ensures that the component can operate effectively even in harsh conditions, making it a reliable choice for industries such as power generation, oil and gas, and manufacturing.

One of the key technologies integrated into the 197D7799P001 is advanced sensor technology. This feature enables real-time monitoring of performance metrics, which aids in predictive maintenance and reduces the likelihood of unexpected failures. With the ability to provide accurate data, operators can make informed decisions that enhance overall system efficiency and minimize downtime.

Another significant characteristic of the GE 197D7799P001 is its compatibility with various automation systems. The component is designed to seamlessly integrate with existing infrastructure, providing an adaptable solution for various applications. This interoperability is crucial for facilities looking to upgrade their systems without incurring extensive costs associated with complete overhauls.

The component also boasts enhanced connectivity features that support remote monitoring and troubleshooting. By utilizing industry-standard communication protocols, the 197D7799P001 allows operators to access crucial data from anywhere, thus facilitating quicker response times and improving overall operational efficiency.

Furthermore, the GE 197D7799P001 is known for its energy efficiency, contributing to reduced operational costs. Its design minimizes energy consumption while maintaining peak performance levels, aligning with global efforts towards sustainability and resource conservation.

In conclusion, the GE 197D7799P001 is a highly versatile component that combines durability, advanced sensor technology, and energy efficiency. Its ability to integrate with existing systems, coupled with robust monitoring capabilities, makes it an invaluable asset for industries aiming to enhance productivity and operational reliability. As industries continue to evolve, components like the GE 197D7799P001 will play a crucial role in shaping their future.
Top Page Image Contents