GE 197D7799P001 OperatingInstructions, InstallationInstructions, Support TroubleshootingTips

Page 4

Safety Instructions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.

OperatingInstructions

The power cord of this appliance is equipped with a 3- prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.

Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.

The refrigerator should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate.

This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.

Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.

When moving the refrigerator away from the wall, be careful not to roll over or damage the power cord.

InstallationInstructions

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

MESURES DE SÉCURITÉ IMPORTANTES.

LISEZ D’ABORD TOUTES LES DIRECTIVES.

AVERTISSEMENT!

RACCORDEMENT ÉLECTRIQUE

Ne coupez ni retirez en aucun cas la troisième broche (mise à la terre) de la fiche du cordon d’alimentation. Pour votre sécurité, cet appareil doit être correctement mis à la terre.

Support TroubleshootingTips

Le cordon d’alimentation de cet appareil est muni d’une fiche à 3 broches (mise à la terre) qui se branche dans une prise murale ordinaire à 3 alvéoles (mise à la terre) pour réduire au minimum les risques de chocs électriques.

Faites examiner la prise de courant et le circuit par un électricien qualifié pour vous assurer que la prise est correctement mise à la terre.

Si la prise murale est du type standard à 2 alvéoles, il vous incombe de la faire remplacer par une prise à 3 alvéoles correctement mise à la terre.

Le réfrigérateur doit toujours être branché dans sa propre prise de courant, dont la tension nominale est identique à celle indiquée sur la plaque signalétique.

Cette précaution est recommandée pour garantir un rendement optimum et éviter une surcharge des circuits électriques de la résidence, ce qui pourrait créer un risque d’incendie par surchauffe des fils.

Ne débranchez jamais le réfrigérateur en tirant sur le cordon d’alimentation. Saisissez fermement la fiche du cordon et tirez droit pour la retirer de la prise.

Réparez ou remplacez immédiatement tout cordon effiloché ou endommagé. N’utilisez pas un cordon fendillé ou présentant des signes d’usure.

Lorsque vous déplacez votre réfrigérateur du mur, faites attention de ne pas le faire rouler sur le cordon d’alimentation afin de ne pas l’endommager.

Consumer

VEUILLEZ LIRE ET SUIVRE ATTENTIVEMENT CES MESURES DE SÉCURITÉ.

CONSERVEZ CES DIRECTIVES

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Refrigerators Write the model and serial numbers here Model # Serial #Refrigerants TroubleshootingTipsRéfrigérants Instructions Troubleshooting Operating Instructions InstallationTips Consumer Support InstallationInstructions Support TroubleshootingTipsOperatingInstructions ConsumerAbout the temperature control dial About the fresh food compartment shelvesAbout the freezer compartment shelves About the storage drawersStep Shelf Fruit and Vegetable DrawersSafety Instructions Operating Troubleshooting Tips Consumer SupportAbout storage drawer and cover removal About the automatic icemakerSupport Care and cleaning of the refrigeratorConsumer Before YOU Begin Refrigerator LocationClearances Rollers and Leveling LegsBefore YOU Begin Installing the Water Line on Some ModelsWhat YOU will Need Shut OFF the Main Water Supply and Unplug Refrigerator Drill the Hole for the ValveFasten the Shutoff Valve Route the TubingInstalling the Water Line Turn the Water On AT Shutoff ValvePlug in the Refrigerator Start the IcemakerReversing the Door Swing Important NotesTools Required Remove the Freezer DoorReversing the Hardware Remove the Fresh Food DoorReversing the Door Handles Transfer fresh food door handleRE-HANGING the Doors Reversing the Door HandlesBefore you call for service… Normal operating soundsSafety Instructions InstructionsCustomer Warranty Consumer Product Ownership Registration For refrigerators installed in the U.S GE Consumer & Industrial GE Will Replace Instructions TroubleshootingWhat GE Will Not Cover GE Appliances Website

197D7799P001 specifications

The GE 197D7799P001 is a cutting-edge component designed for use in various industrial and commercial applications, primarily focusing on enhancing operational efficiency and reliability. This model exemplifies GE's commitment to innovation and performance, which is evident in its advanced features, technologies, and characteristics.

At its core, the 197D7799P001 is engineered to deliver exceptional performance in demanding environments. One of its standout features is its robust design, which allows it to withstand high levels of stress and abrasion. This durability ensures that the component can operate effectively even in harsh conditions, making it a reliable choice for industries such as power generation, oil and gas, and manufacturing.

One of the key technologies integrated into the 197D7799P001 is advanced sensor technology. This feature enables real-time monitoring of performance metrics, which aids in predictive maintenance and reduces the likelihood of unexpected failures. With the ability to provide accurate data, operators can make informed decisions that enhance overall system efficiency and minimize downtime.

Another significant characteristic of the GE 197D7799P001 is its compatibility with various automation systems. The component is designed to seamlessly integrate with existing infrastructure, providing an adaptable solution for various applications. This interoperability is crucial for facilities looking to upgrade their systems without incurring extensive costs associated with complete overhauls.

The component also boasts enhanced connectivity features that support remote monitoring and troubleshooting. By utilizing industry-standard communication protocols, the 197D7799P001 allows operators to access crucial data from anywhere, thus facilitating quicker response times and improving overall operational efficiency.

Furthermore, the GE 197D7799P001 is known for its energy efficiency, contributing to reduced operational costs. Its design minimizes energy consumption while maintaining peak performance levels, aligning with global efforts towards sustainability and resource conservation.

In conclusion, the GE 197D7799P001 is a highly versatile component that combines durability, advanced sensor technology, and energy efficiency. Its ability to integrate with existing systems, coupled with robust monitoring capabilities, makes it an invaluable asset for industries aiming to enhance productivity and operational reliability. As industries continue to evolve, components like the GE 197D7799P001 will play a crucial role in shaping their future.
Top Page Image Contents