GE 197D7799P001 Before YOU Begin, Refrigerator Location, Clearances, Rollers and Leveling Legs

Page 9

Installation Instructions Models 16, 17, 18

If you have questions, call 1.800.GE.CARES or visit our Website at: ge.com

In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•IMPORTANT – Save these

instructions for local inspector’s use.

•IMPORTANT – Observe all

governing codes and ordinances.

•Note to Installer – Be sure to leave these instructions with the Consumer.

•Note to Consumer – Keep these instructions for future reference.

•Skill level – Installation of this appliance requires basic mechanical skills.

•Completion time – Refrigerator Installation

15 minutes

Reversing the Door Swing

1hour

•Proper installation is the responsibility of the installer.

•Product failure due to improper installation is not covered under the Warranty.

WATER SUPPLY TO THE ICEMAKER (on some models)

If the refrigerator has an icemaker, it will have to be connected to a cold water line. A water supply kit (containing copper tubing, shutoff valve, fittings and instructions) is available at extra cost from your dealer, by visiting our Website at ge.com (in Canada at www.geappliances.ca) or from Parts and Accessories, 1.800.661.1616.

REFRIGERATOR LOCATION

•Do not install the refrigerator where the temperature will go below 60°F (16°C) because it will not run often enough to maintain proper temperatures.

•Install it on a floor strong enough to support it fully loaded.

CLEARANCES

Allow the following clearances for ease of installation, proper air circulation and plumbing and electrical connections.

•Sides 3/4″ (19 mm)

•Top 1″ (25 mm)

•Back 1″ (25 mm)

ROLLERS AND LEVELING LEGS

Leveling legs near each front corner of the refrigerator are adjustable. They firmly position the refrigerator and prevent it from moving when the doors are opened. Leveling legs should be set so the front of the refrigerator is raised just enough that the doors close easily when opened about halfway.

Turn the leveling legs clockwise to raise the refrigerator, counterclockwise to lower it.

Rollers next to the leveling legs allow you to move the refrigerator away from the wall for cleaning.

Turn the legs counterclockwise until the weight of the refrigerator is transferred from them to the rollers. After rolling the refrigerator back into place, turn the legs clockwise until the legs again bear the weight of the refrigerator.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Write the model and serial numbers here Model # Serial # RefrigeratorsTroubleshootingTips RefrigerantsRéfrigérants Operating Instructions Installation Instructions TroubleshootingTips Consumer Support Support TroubleshootingTips InstallationInstructionsOperatingInstructions ConsumerAbout the fresh food compartment shelves About the temperature control dialAbout the storage drawers About the freezer compartment shelvesStep Shelf Fruit and Vegetable DrawersTroubleshooting Tips Consumer Support Safety Instructions OperatingAbout storage drawer and cover removal About the automatic icemakerCare and cleaning of the refrigerator SupportConsumer Refrigerator Location Before YOU BeginClearances Rollers and Leveling LegsInstalling the Water Line on Some Models Before YOU BeginWhat YOU will Need Drill the Hole for the Valve Shut OFF the Main Water Supply and Unplug RefrigeratorFasten the Shutoff Valve Route the TubingTurn the Water On AT Shutoff Valve Installing the Water LinePlug in the Refrigerator Start the IcemakerImportant Notes Reversing the Door SwingTools Required Remove the Freezer DoorRemove the Fresh Food Door Reversing the HardwareTransfer fresh food door handle Reversing the Door HandlesReversing the Door Handles RE-HANGING the DoorsNormal operating sounds Before you call for service…Instructions Safety InstructionsCustomer Warranty Consumer Product Ownership Registration For refrigerators installed in the U.S GE Consumer & Industrial Instructions Troubleshooting GE Will ReplaceWhat GE Will Not Cover GE Appliances Website

197D7799P001 specifications

The GE 197D7799P001 is a cutting-edge component designed for use in various industrial and commercial applications, primarily focusing on enhancing operational efficiency and reliability. This model exemplifies GE's commitment to innovation and performance, which is evident in its advanced features, technologies, and characteristics.

At its core, the 197D7799P001 is engineered to deliver exceptional performance in demanding environments. One of its standout features is its robust design, which allows it to withstand high levels of stress and abrasion. This durability ensures that the component can operate effectively even in harsh conditions, making it a reliable choice for industries such as power generation, oil and gas, and manufacturing.

One of the key technologies integrated into the 197D7799P001 is advanced sensor technology. This feature enables real-time monitoring of performance metrics, which aids in predictive maintenance and reduces the likelihood of unexpected failures. With the ability to provide accurate data, operators can make informed decisions that enhance overall system efficiency and minimize downtime.

Another significant characteristic of the GE 197D7799P001 is its compatibility with various automation systems. The component is designed to seamlessly integrate with existing infrastructure, providing an adaptable solution for various applications. This interoperability is crucial for facilities looking to upgrade their systems without incurring extensive costs associated with complete overhauls.

The component also boasts enhanced connectivity features that support remote monitoring and troubleshooting. By utilizing industry-standard communication protocols, the 197D7799P001 allows operators to access crucial data from anywhere, thus facilitating quicker response times and improving overall operational efficiency.

Furthermore, the GE 197D7799P001 is known for its energy efficiency, contributing to reduced operational costs. Its design minimizes energy consumption while maintaining peak performance levels, aligning with global efforts towards sustainability and resource conservation.

In conclusion, the GE 197D7799P001 is a highly versatile component that combines durability, advanced sensor technology, and energy efficiency. Its ability to integrate with existing systems, coupled with robust monitoring capabilities, makes it an invaluable asset for industries aiming to enhance productivity and operational reliability. As industries continue to evolve, components like the GE 197D7799P001 will play a crucial role in shaping their future.
Top Page Image Contents